TERMINALS OF ECM
System information · Vehicles built from Nov 2005


- HINT:
- Each ECM terminal's standard voltage is shown in the table below.
- In the table, first follow the information under "Condition". Look under "Symbols (Terminal No.)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
- Use the illustration above as a reference for the ECM terminals.
| Symbols (Terminal No.) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
| +B (A49-42) - E1 (A49-2) |
B - W-B |
Power source of ECM |
Ignition switch on (IG) |
9 to 14 V |
| +B1 (A49-1) - E1 (A49-2) |
B - W-B |
Power source of ECM |
Ignition switch on (IG) |
9 to 14 V |
| IGSW (A49-70) - E1 (A49-2) |
R - W-B |
Ignition switch |
Ignition switch on (IG) |
9 to 14 V |
| MREL (A49-44) - E1 (A49-2) |
GR - W-B |
ECD relay |
Ignition switch on (IG) |
0 to 1.5 V |
| 20 seconds elapsed after ignition switch off |
9 to 14 V |
|||
| GREL (A49-81) - E1 (A49-2) |
W - W-B |
Glow plug relay |
Ignition switch on (IG) at cold engine (Engine coolant temperature is less than 20°C (68°F)) |
0 to 1.5 V |
| Idling with warm engine |
9 to 14 V |
|||
| VPA (A49-15) - EPA (A49-56) |
R - G |
Accelerator pedal position sensor (for engine control) |
Ignition switch on (IG), accelerator pedal fully released |
0.6 to 1.0 V |
| Ignition switch on (IG), accelerator pedal fully depressed |
3.0 to 4.6 V |
|||
| VPA2 (A49-14) - EPA2 (A49-55) |
L - BR |
Accelerator pedal position sensor (for sensor malfunction detection) |
Ignition switch on (IG), accelerator pedal fully released |
1.4 to 1.8 V |
| Ignition switch on (IG), accelerator pedal fully depressed |
3.7 to 5.0 V |
|||
| VCPA (A49-34) - EPA (A49-56) |
B - G |
Power source of accelerator pedal position sensor (for VPA1) |
Ignition switch on (IG) |
4.5 to 5.5 V |
| VCP2 (A49-33) - EPA2 (A49-55) |
W - BR |
Power source of accelerator pedal position sensor (for VPA2) |
Ignition switch on (IG) |
4.5 to 5.5 V |
| VG (C50-36) - EVG (C50-15) |
GR - V |
Mass air flow meter |
Idling |
0.5 to 3.4V |
| THA (C50-7) - ETHA (C50-6) |
P - R |
Intake air temperature sensor |
Idling, intake air temperature at 20°C (68°F) |
0.5 to 3.4 V |
| VCS (C50-29) - E2S (C50-16) |
BR - G |
Power source of sensor (a specific voltage) |
Ignition switch on (IG) |
4.5 to 5.5 V |
| PC (C50-37) - E2S (C50-16) |
B - G |
Common rail pressure sensor |
Idling |
1.1 to 1.4 V |
| VN (C50-33) - E1 (A49-2) |
W - W-B |
VRV (for VN turbocharger) |
Idling |
Pulse generation (See waveform 1) |
| PCV (C50-12) - E1 (A49-2) |
P - W-B |
Supply pump (fuel metering unit) |
Idling |
Pulse generation (See waveform 2) |
| CLSW (A49-69) - E1 (A49-2) |
W - W-B |
Clutch switch |
Clutch pedal depressed |
9 to 15 V |
| Clutch pedal released |
0 to 1.5 V |
|||
| EGR1 (A49-12) - E1 (A49-2) |
R - W-B |
EGR valve |
Racing engine |
Pulse generation (See waveform 3) |
| EGR2 (A49-11) - E1 (A49-2) |
LG - W-B |
|||
| EGR3 (A49-31) - E1 (A49-2) |
W - W-B |
|||
| EGR4 (A49-30) - E1 (A49-2) |
Y - W-B |
|||
| #10 (C50-21) - PINJ1 (C50-1) #20 (C50-22) - PINJ2 (C50-2) #30 (C50-23) - PINJ3 (C50-3) #40 (C50-24) - PINJ4 (C50-20) |
L - B W - R L - Y R - W |
Injector |
Idling |
Pulse generation (See waveform 4) |
| THF (A50-39) - ETHF (A50-18) |
O - P |
Fuel temperature sensor |
Idling |
0.5 to 3.4 V |
| THW (C50-40) - ETHW (C50-32) |
L - BR |
ECT sensor |
Idling, engine coolant temperature at 80°C (176°F) |
0.2 to 1.0 V |
| ALT (C50-5) - E1 (A49-2) |
P - W-B |
Generator (Alternator) duty ratio |
Idling |
Pulse generation |
| LUSL (C50-13) - E1 (A49-2) |
L - W-B |
Intake shutter duty signal |
Racing engine |
Pulse generation (See waveform 5) |
| PRV (C50-4) - E1 (A49-2) |
Y - W-B |
Pressure control valve signal |
Drive vehicle at 50 km/h (31 mph) with third gear, and then decelerate by releasing accelerator pedal |
Pulse generation (See waveform 6) |
| G1 (C50-26) - EG (C50-34) |
R - G |
Camshaft position sensor |
Idling |
Pulse generation (See waveform 7) |
| NE+ (C50-10) - NE- (C50-11) |
L - P |
Crankshaft position sensor |
Idling |
Pulse generation (See waveform 7) |
| VVLU (C50-31) - EVLU (C50-14) |
W - LG |
Power source of sensor (a specific voltage) |
Ignition switch on (IG) |
4.5 to 5.5 V |
| VLU (C50-35) - EVLU (C50-14) |
B - LG |
Intake shutter position sensor |
Ignition switch on (IG), intake shutter fully opened |
3.5 to 4.5 V |
| Ignition switch on (IG), intake shutter fully closed |
0.4 to 1.0 V |
|||
| PIM (C50-38) - EPIM (C50-17) |
GR - Y |
Manifold absolute pressure sensor |
Ignition switch on (IG) (Same as atmospheric pressure) |
2.0 to 2.6 V |
| VPIM (C50-30) - EPIM (C50-17) |
W - Y |
Power source of sensor (a specific voltage) |
Ignition switch on (IG) |
4.5 to 5.5 V |
| TACH (A49-20) - E1 (A49-2) |
LG - W-B |
Engine speed |
Idling |
Pulse generation |
| STP (A49-8) - E1 (A49-2) |
G - W-B |
Stop light switch |
Brake pedal depressed |
7.5 to 14 V |
| Brake pedal released |
0 to 1.5 V |
|||
| ST1 (A49-27) - E1 (A49-2) |
Y (M/T) - W-B L (MMT) - W-B |
Stop light switch (opposite to STP) |
Ignition switch on (IG), brake pedal depressed |
0 to 1.5 V |
| Ignition switch on (IG), brake pedal released |
7.5 to 14 V |
|||
| TC (A49-28) - E1 (A49-2) |
P - W-B |
Terminal TC of DLC3 |
Ignition switch on (IG) |
9 to 14 V |
| SIL (A49-5) - E1 (A49-2) |
W - B |
Terminal SIL of DLC3 |
Connect intelligent tester to DLC3 |
Pulse generation |
| SPD (A49-66) - E1 (A49-2) |
V - W-B |
Speed signal from combination meter |
Ignition switch on (IG), driving wheel rotating slowly |
Pulse generation (See waveform 8) |
| STA (A49-9) - E1 (A49-2) |
BR - W-B |
Starter signal |
Cranking |
6.0 V or more |
| W (A49-23) - E1 (A49-2) |
B - W-B |
MIL |
MIL illuminated |
0 to 3 V |
| MIL not illuminated |
9 to 14 V |
|||
| STSW (A49-26) - E1 (A49-2) |
B - W-B |
Ignition switch signal |
Shift lever position N, ignition switch START |
6.0 V or more |
| STAR (A49-78) - E1 (A49-2) |
O - W-B |
Starter relay control |
Ignition switch on (IG) |
Below 1.5 V |
| Cranking |
6.0 V or more |
|||
| ACCR (A49-62) - E1 (A49-2) |
G - W-B |
ACC relay control signal |
Cranking |
Below 1.5 V |
| ELS (A49-10) - E1 (A49-2) |
G - W-B |
Electric load |
Tail light switch on |
7.5 to 14 V |
| Tail light switch off |
Below 1.5 V |
|||
| ELS2 (A49-68) - E1 (A49-2) |
V - W-B |
Electric load |
Defogger switch on |
7.5 to 14 V |
| Defogger switch off |
Below 1.5 V |
|||
| FAN (A49-71) - E1 (A49-2) |
O - W-B |
Fan No. 1 relay |
Ignition switch on (IG) |
9 to 14 V |
| Idling with warm engine |
Below 1.5 V |
|||
| FAN2 (A49-52) - E1 (A49-2) |
LG - W-B |
Fan No. 2 relay |
Idling with high engine coolant temperature |
Below 1.5 V |
| CAN+ (A49-45) - E1 (A49-2) |
W - W-B |
CAN communication line |
Ignition switch on (IG) |
Pulse generation (See waveform 9) |
| CAN- (A49-64) - E1 (A49-2) |
B - W-B |
CAN communication line |
Ignition switch on (IG) |
Pulse generation (See waveform 10) |
| CANH (A49-24) - E1 (A49-2) |
L - W-B |
CAN communication line |
Ignition switch on (IG) |
Pulse generation (See waveform 9) |
| CANL (A49-46) - E1 (A49-2) |
W - W-B |
CAN communication line |
Ignition switch on (IG) |
Pulse generation (See waveform 10) |
| Waveform 1 |
VRV for turbocharger signal

Symbols (Terminal No.)
VN (C50-33) - E1 (A49-2)
Tool setting
5 V/DIV., 1 msec./DIV.
Condition
Idling with warm engine
- HINT:
- The waveform charges depending on the VRV for turbocharger operation.
| Waveform 2 |
Suction control valve signal

Symbols (Terminal No.)
PCV (C50-12) - E1 (A49-2)
Tool Setting
5 V/DIV., 5 msec./DIV.
Condition
Idling or cranking with warm engine
- HINT:
- The waveform varies depending on the suction control valve operation.
| Waveform 3 |
EGR valve signal

Symbols (Terminal No.)
(a) EGR1 (A49-12) - E1 (A49-2)
(b) EGR2 (A49-11) - E1 (A49-2)
(c) EGR3 (A49-31) - E1 (A49-2)
(d) EGR4 (A49-30) - E1 (A49-2)
Tool Setting
10 V/ DIV., 0.5 msec./ DIV.
Condition
Repeating quick engine RPM accelerations
- HINT:
- The waveform varies depending on the EGR valve operation.
- When driving conditions become stable (e.g. while the engine is idling), the EGR valve closes and the waveform may disappear.
- The waveform varies depending on the EGR valve operation.
| Waveform 4 |
Injector No. 1 injection signal

Injector No. 2 injection signal
Injector No. 3 injection signal
Injector No. 4 injection signal
Symbols (Terminal No.)
(a) #10 (C50-21) - PINJ1 (C50-1)
(b) #20 (C50-22) - PINJ2 (C50-2)
(c) #30 (C50-23) - PINJ3 (C50-3)
(d) #40 (C50-24) - PINJ4 (C50-20)
Tool Setting
5 V/DIV., 20 msec./DIV.
Condition
Idling with warm engine
- HINT:
- The waveform varies depending on the injector injection.
| Waveform 5 |
Intake shutter signal

Symbols (Terminal No.)
LUSL (C50-13) - E1 (A49-2)
Tool setting
5 V/ DIV., 2 msec./ DIV.
Condition
Idling with warm engine
- HINT:
- The waveform varies depending on the intake shutter operation.
| Waveform 6 |
Pressure control valve signal

Symbols (Terminal No.)
PRV (C50-4) - E1 (A49-2)
Tool setting
10 V/ DIV., 0.5 msec./ DIV.
Condition
Idling with warm engine
- HINT:
- The waveform varies depending on the pressure discharge valve operation.
| Waveform 7 |
Crankshaft position sensor signal

Camshaft position sensor signal
Symbol (Terminal No.)
(a) NE+ (C50-10) - NE- (C50-11)
(b) G1 (C50-26) - EG (C50-34)
Tool Setting
10 msec./DIV.
Condition
Idling with warm engine
- HINT:
- The waveform varies depending on the engine revolution.
| Waveform 8 |
Vehicle speed signal

Symbols (Terminal No.)
SPD (A49-66) - E1 (A49-2)
Tool Setting
1 V/DIV., 10 msec./DIV.
Condition
While driving the vehicle
- HINT:
- The wavelength becomes shorter as the vehicle speed increases.
| Waveform 9 |
CAN communication signal

Symbols (Terminal No.)
CANH (A49-24), CAN+ (A49-45) - E1 (A49-2)
Tool Setting
1 V/DIV., 10 msec./DIV.
Condition
Engine stopped, ignition switch on (IG)
- HINT:
- The wavelength becomes shorter as the CAN communication signal
| Waveform 10 |
CAN communication signal

Symbols (Terminal No.)
CANL (A49-46), CAN- (A49-64) - E1 (A49-2)
Tool Setting
1 V/DIV., 10 msec./DIV.
Condition
Engine stopped, ignition switch on (IG)
- HINT:
- The waveform varies depending on the CAN communication signal.