2005-2008 Yaris · Service Manual ENGINE

DIAGNOSIS SYSTEM

Troubleshooting · Vehicles built from Nov 2005


DESCRIPTION
A093827E01
  1. When troubleshooting a Euro-OBD (On-Board Diagnostic) vehicle, an intelligent tester or OBD scan tool must be connected to the DLC3 (Data Link Connector 3) of the vehicle. Various data in the vehicle's ECM (Engine Control Module) can be then read.

  2. Euro-OBD regulations require that the vehicle's on- board computer illuminates the MIL (Malfunction Indicator Lamp) in the instrument panel when the computer detects malfunctions in:

    1. The emission control system and components.

    2. The power train control components (which affect vehicle emissions).

    3. The computer itself. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.

  3. To check the DTCs, connect an intelligent tester to the DTC3. The tester displays DTCs, freeze frame data, and variety of engine data. The DTCs and freeze frame data can be cleared with the tester (refer to DTC CHECK/CLEAR (Click here)).


NORMAL MODE AND CHECK MODE
The diagnosis system operates in "normal mode" during normal vehicle use. In normal mode, "2 trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1 trip detection logic" is used for simulating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent malfunctions (intelligent tester only) (Click here).
A107925E01

2 TRIP DETECTION LOGIC
When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the next subsequent drive cycle, the MIL is illuminated (2nd trip).

FREEZE FRAME DATA
Freeze frame data records the engine conditions (fuel system, calculated engine load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

DLC3 (Data Link Connector 3)

  1. H100769E16
    The vehicle's ECM uses the ISO 15765-4 for communication protocol. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.
    Symbols
    Terminal No.
    Name
    Reference terminal
    Result
    Condition
    SIL
    7
    Bus "+" line
    5 - signal ground
    Pulse generation
    During transmission
    CG
    4
    Chassis ground
    Body ground
    1 Ω or less
    Always
    SG
    5
    Signal ground
    Body ground
    1 Ω or less
    BAT
    16
    Battery positive
    Body ground
    9 to 14 V
    CANH
    6
    CAN "High" Line
    14 - CANL
    54 to 69 Ω
    Ignition switch off *
    Battery positive
    6 kΩ or higher
    4 - CG
    200 Ω or higher
    CANL
    14
    CAN "Low" Line
    Battery positive
    6 kΩ or higher
    4 - CG
    200 Ω or higher

    NOTICE:
    *: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.

    HINT:
    Connect the cable of the intelligent tester to the DLC3, turn the ignition switch on (IG) and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.

    1. If communication is normal when the tester is connected to another vehicle, inspect the DLC3 on the original vehicle.
    2. If communication is still not possible when the tester is connected to another vehicle, the problem is probably in the tester itself. Consult the Service Department listed in the tester's instruction manual.


INSPECT BATTERY VOLTAGE
If the voltage is below 11 V, recharge or replace the battery before proceeding.

Battery voltage:
11 to 14 V


CHECK MIL

  1. A093827E01
    The MIL illuminates when the ignition switch is turned on (IG) and the engine is not running.

    HINT:
    If the MIL is not illuminated, check the MIL circuit (Click here).

  2. When the engine is started, the MIL should turn OFF. If the lamp remains ON, the diagnosis system has detected a malfunction or abnormality in the system.

← TERMINALS OF ECM (from Nov 2005)DTC CHECK / CLEAR (from Nov 2005) →