2005-2008 Yaris · Service Manual STEERING

INSTALLATION

Removal / installation · Vehicles built from Aug 2005


1. INSTALL STEERING COLUMN ASSEMBLY

C117203
  1. Install the steering column assembly onto the instrument panel reinforcement assembly with the bolt and 2 nuts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Connect all the connectors and clamp the wire harnesses onto the steering post assembly bracket.


2. INSTALL BRAKE PEDAL (for Automatic Transaxle)
  1. Apply MP grease No. 2 to the brake master cylinder push rod clevis pin and installation surfaces.

  1. Install the 2 brake pedal bushes, and install the brake pedal with the nut and brake pedal shaft.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

  1. C119065
    Apply MP grease No. 2 to the brake master cylinder push rod clevis pin and installation surfaces.

  1. Connect the brake master cylinder push rod clevis to the brake pedal with the brake master cylinder push rod clevis pin, install the clip onto the brake master cylinder push rod clevis pin, and then install the brake pedal return spring.


3. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for Manual Transaxle)

C116881
  1. Install the pedal support with the bolt and 4 nuts.

    Torque:
    Bolt:
    24 N*m{ 241 kgf*cm , 17 ft.*lbf }
    Nut:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


4. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS (for Manual Transaxle)
  1. Apply lithium soap base glycol grease to the push rod pin.

  1. C116880
    Install the push rod clevis with the push rod pin and clip.

  1. Install the brake pedal return spring.


5. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY NO. 2

G028410E01
  1. Connect all the connectors and clamp the wire harnesses onto the steering post assembly bracket.

  1. Align the matchmarks on steering intermediate shaft assembly No. 2 and the steering sliding yoke and provisionally install them with bolt C.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }

  1. Align the matchmarks on the steering sliding yoke and steering gear assembly and install them with bolt B.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    28 N*m{ 290 kgf*cm , 21 ft.*lbf }


6. INSTALL COLUMN HOLE COVER SILENCER SHEET

A116501
  1. Install the column hole cover plate with the 2 clips.

  1. Install the floor carpet.


7. INSTALL INSTRUMENT PANEL UNDER TRAY (w/o Knee Airbag)

B108187
  1. Engage the 4 claws and install the instrument panel under tray.

  1. Install the 2 <A> screws.

  1. B108186
    Engage the 4 claws and install the instrument panel under tray.


8. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Knee Airbag)

C125678E01
  1. Engage the 6 claws.

  1. Install the driver side knee airbag assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


9. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY NO. 1

  1. B114571
    Engage the 4 claws and install the instrument panel under cover.


10. CONNECT POWER STEERING ECU

C117192
  1. Connect the 2 steering post assembly connectors to the power steering ECU.

  1. Install the power steering motor harness and torque sensor wire harness clamps onto the side of the power steering ECU.

  1. Tilt the steering post assembly up and down to make sure that the power steering motor harness and torque sensor wire harness do not interfere with any components.


11. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY UPPER

B108233E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the upper side of the instrument panel.

  1. Engage the claw and the 3 clips at the lower side of the instrument panel.

    B105355E01

  1. Install the instrument panel upper with the 2 <C> bolts and the 4 <B> screws.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt

  1. Connect the connectors.

    B105354E01

  1. B108182
    Connect the passenger airbag connector and clamp.


12. INSTALL SWITCH BASE HOLE COVER

B108201
  1. Disengage the 2 clips and 2 claws and install the switch hole base.


13. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

B105352
  1. Engage the claw of the hinge portion in the horizontal direction to install the glove compartment door assembly.

    NOTICE:
    Engage the claw in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.

  1. B108202
    Slightly deform the upper portion of the glove compartment door assembly to engage the stopper.


14. INSTALL FRONT PILLAR GARNISH RH

  1. B114342E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B127672
    w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.

    3. B127674
      Connect the speaker connector.

  1. B114312
    Install the 3 antenna cord clamps.

  1. Connect the connector.

  1. w/ Curtain Shield Airbag:

    1. B117697E01
      Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. w/o Curtain Shield Airbag:

    1. B117694
      Engage the 2 clips and the 2 claws and install the front pillar garnish.


15. INSTALL FRONT PILLAR GARNISH LH

  1. B114344E01
    w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.

  1. B127671
    w/ Front No. 2 Speaker:

    1. Insert the hook into the body hole.

    2. Engage the clip and install the front speaker.

    3. B127673
      Connect the speaker connector.

  1. B114316
    Install the 4 wire harness clamps.

  1. w/ Curtain Shield Airbag:

    1. B117698E01
      Install a new special clip and the clip onto a new front pillar garnish.

    2. Engage the 2 clips and the 2 claws and install the front pillar garnish.

  1. w/o Curtain Shield Airbag:

    1. B114318
      Engage the 2 clips and the 2 claws and install the front pillar garnish.


16. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Install the front door opening trim weatherstrip.


17. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure for the RH side as for the LH side.


18. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY CENTER

B132366E01
  1. Fit the 3 A claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.

  1. B132367
    Engage the 4 claws and 5 clips and install the instrument cluster finish panel.


19. INSTALL COMBINATION METER ASSEMBLY

E107730
  1. Install the combination meter assembly with the 2 screws.

  1. Connect the 2 connectors.


20. INSTALL INSTRUMENT CLUSTER FINISH PANEL

B132366E01
  1. Fit the 3 A claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.

  1. B132367
    Engage the 4 claws and 5 clips and install the instrument cluster finish panel.


21. INSTALL INSTRUMENT PANEL FINISH PANEL END RH

E107743
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end RH.

  1. E107744
    Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end RH.


22. INSTALL INSTRUMENT PANEL FINISH PANEL END LH

E107741
  1. with CD player

    1. Connect the connector.

    2. Engage the 4 claws and 3 clips and install the instrument panel finish panel end LH.

  1. E107742
    Except CD player

    1. Connect the connector.

    2. Engage the 5 claws and 3 clips and install the instrument panel finish panel end LH.


23. INSTALL COMBINATION SWITCH ASSEMBLY

C117206
  1. Install the turn signal switch assembly with spiral cable onto the steering post assembly with the clamp.

  1. Connect all the connectors to the turn signal switch with spiral cable.


24. INSTALL STEERING COLUMN COVER

  1. C117205E01
    Engage the claw to install the steering column upper cover.

  1. C117204E01
    Engage the 2 claws to install the steering column lower cover.

  1. Install the 3 screws.


25. INSTALL STEERING COLUMN COVER SUPPORT (w/ Entry and Start System)

B108275E01
  1. Engage the 4 claws to install the steering column cover support.


26. INSTALL STEERING WHEEL ASSEMBLY

  1. C117210E01
    Align the matchmarks and install the steering wheel assembly onto the steering column assembly.

  1. Install the nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect all connectors to the spiral cable.


27. INSTALL STEERING PAD (w/o Steering Pad Switch)

C117196E01

NOTICE:
Do not use a steering pad that has been dropped.

  1. Confirm that the ignition switch is turned to off.

  1. Confirm that the negative battery terminal is detached.

    CAUTION:
    Do not begin the operation for at least 90 seconds after the negative battery terminal is detached.

  1. Connect the horn terminal.

  1. Connect the airbag connector.

    NOTICE:
    Securely lock the locking button.

  1. C121183
    Install the steering pad.

  1. Using "Torx" socket wrench T30, tighten the 2 bolts.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }

    NOTICE:
    Tighten the 2 bolts while holding the steering pad to prevent it moving upward.


28. INSTALL STEERING PAD (w/ Steering Pad Switch)

C117200E01
  1. Connect the horn terminal.

  1. Connect the airbag connector.

    NOTICE:
    Securely lock the locking button.

  1. C121184
    Install the steering pad.

  1. Using "Torx" socket wrench T30, tighten the 2 bolts.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }

    NOTICE:
    Tighten the 2 bolts while holding the steering pad to prevent it moving upward.


29. POSITION FRONT WHEEL FACING STRAIGHT AHEAD

30. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


31. CHECK SRS WARNING LIGHT TURNS OFF
(Click here)

32. PERFORM CALIBRATION OF TORQUE SENSOR ZERO POINT
(Click here)
← REASSEMBLY (from Aug 2005)COMPONENTS (from Nov 2005) →