INSTALLATION
Removal / installation · Vehicles built from Nov 2005
| 1. INSTALL POWER STEERING ECU |
Install the power steering ECU with the 2 nuts.

- Torque:
- 5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
Connect the 4 connectors.

Install the wire harness clamp.

- NOTICE:
- Make sure that the wire harness of the steering column assembly is installed onto the power steering ECU bracket and that it is not pulled too tightly.
| 2. INSTALL MULTI-MODE MANUAL TRANSAXLE ECU (for Multi-Mode Manual Transaxle LHD) |
![]() ![]() |
Engage the clip and install the transmission control ECU.
Install the 2 bolts.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Connect the 3 connectors.

| 3. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY UPPER |
![]() ![]() |
Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).
Engage the 5 claws at the upper side of the instrument panel.
Engage the claw and the 3 clips at the lower side of the instrument panel.


Install the instrument panel upper with the 2 <C> bolts and the 4 <B> screws.
- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt
Connect the connectors.


Connect the passenger airbag connector and clamp.

| 4. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() ![]() |
Engage the claw of the hinge portion in the horizontal direction to install the glove compartment door assembly.
- NOTICE:
- Engage the claw in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.
Slightly deform the upper portion of the glove compartment door assembly to engage the stopper.

| 5. INSTALL FRONT PILLAR GARNISH RH |
w/ Curtain Shield Airbag:

Remove the piece of cloth or nylon.
Insert the hook into the body hole.

Engage the clip and install the front No. 2 speaker.
Connect the speaker connector.

Install the 3 clamps.

Connect the connector.
w/ Curtain Shield Airbag:

Install a new special clip and the clip onto a new front pillar garnish.
Engage the 2 clips and the 2 claws and install the front pillar garnish.
w/o Curtain Shield Airbag:

Engage the 2 clips and the 2 claws and install the front pillar garnish.
| 6. INSTALL FRONT PILLAR GARNISH LH |
w/ Curtain Shield Airbag:

Remove the piece of cloth or nylon.
Insert the hook into the body hole.

Engage the clip and install the front No. 2 speaker.
Connect the speaker connector.

Install the 4 clamps.

w/ Curtain Shield Airbag:

Install a new special clip and the clip onto a new front pillar garnish.
Engage the 2 clips and the 2 claws and install the front pillar garnish.
w/o Curtain Shield Airbag:

Engage the 2 clips and the 2 claws and install the front pillar garnish.
| 7. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
Install the front door opening trim weatherstrip.
| 8. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
- HINT:
- Use the same procedure for the RH side as for the LH side.
| 9. INSTALL COMBINATION METER ASSEMBLY |
![]() ![]() |
Install the combination meter assembly with the 2 screws.
Connect the 2 connectors.
| 10. INSTALL INSTRUMENT CLUSTER FINISH PANEL |
![]() ![]() |
Fit the 3 A claws of the instrument cluster finish panel into the upper instrument cluster finish panel center.
Engage the 4 claws and 5 clips and install the instrument cluster finish panel.

| 11. INSTALL INSTRUMENT PANEL FINISH PANEL END RH |
![]() ![]() |
with CD player
Connect the connector.
Engage the 4 claws and 3 clips and install the instrument panel finish panel end RH.
Except CD player

Connect the connector.
Engage the 5 claws and 3 clips and install the instrument panel finish panel end RH.
| 12. INSTALL INSTRUMENT PANEL FINISH PANEL END LH |
![]() ![]() |
with CD player
Connect the connector.
Engage the 4 claws and 3 clips and install the instrument panel finish panel end LH.
Except CD player

Connect the connector.
Engage the 5 claws and 3 clips and install the instrument panel finish panel end LH.
| 13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
| 14. PERFORM CALIBRATION OF TORQUE SENSOR ZERO POINT |
| 15. LEARNING OF MULTI-MODE MANUAL TRANSAXLE SYSTEM (for Multi-Mode Manual Transaxle LHD) |
| 16. REMOVE PERFORM SYNCHRONIZATION POSITION CALIBRATION (for Multi-Mode Manual Transaxle LHD) |







