2005-2008 Yaris · Service Manual TRANSMISSION

INITIALIZATION

Troubleshooting · Vehicles built from Nov 2005


INITIALIZATION AND LEARNING USING INTELLIGENT TESTER

HINT:
  1. By using an intelligent tester, initialization and learning of the multi-mode manual transmission system can be performed sequentially. Under manual operation (not using intelligent tester), initialization and learning must be performed individually.
  2. The learning values and the DTC history of the multi-mode manual transmission system are stored in the EEPROM in the transmission control ECU. The stored information is not cleared even when the negative terminal of the battery is disconnected. To clear all the stored information, initialize the transmission control ECU.
  3. Perform the procedure below to ensure that the initialized transmission control ECU stores the adjusted clutch position (stopper position, clamp position, and standby position) or gear position (shift position and select position).
  4. If initialization cannot be performed normally, there may be a malfunction in the shift lever position sensor, NE signals, or CAN communication.
  5. When replacing the following parts, proceed with the operation in the order listed in the table below.

Parts installed
Operation order
See procedure
  1. Transmission assembly
  2. Transmission parts (inside gear box)
  3. Transmission control ECU
1. INITIALIZATION OF MULTI-MODE MANUAL TRANSMISSION SYSTEM
[Initialization of ECU]
See below
2. LEARNING OF MULTI-MODE MANUAL TRANSMISSION SYSTEM
See below
3. SYNCHRONIZATION POSITION CALIBRATION
Click here
  1. Shift and select actuator
  2. Shift stroke sensor
  3. Select stroke sensor
1. INITIALIZATION OF MULTI-MODE MANUAL TRANSMISSION SYSTEM
[Initialization of transmission]
See below
2. LEARNING OF MULTI-MODE MANUAL TRANSMISSION SYSTEM
See below
3. SYNCHRONIZATION POSITION CALIBRATION
Click here
  1. Clutch actuator
  2. Clutch stroke sensor
  3. Clutch disc and clutch cover
  4. Clutch release bearing
  5. Clutch release fork
  6. Flywheel
  7. Crankshaft
1. INITIALIZATION OF MULTI-MODE MANUAL TRANSMISSION SYSTEM
[Initialization of clutch]
See below
2. LEARNING OF MULTI-MODE MANUAL TRANSMISSION SYSTEM
See below
  1. Prepare the vehicle:

    1. Stop the vehicle
    2. Shift the shift lever to the N position.
    3. Turn the ignition switch off.

  2. A107926E01
    Connect the intelligent tester to the DLC3.

  3. Turn the ignition switch on (IG).

  4. Turn the intelligent tester ON.

  5. Select the following menu items: Powertrain / Multi-Mode M/T / Utility / Parts Exchange.

  6. C114373E01
    Read the information.

  7. Press the Next key.

  8. C114374E01
    Read the information.

  9. After checking the vehicle condition, press the Next key.

  10. C114375E01
    Read the information.

  11. Press the Next key.

  12. C114376E01
    Read the information.

  13. Press the Next key.

  14. C114379E01
    On the Multi-Mode M/T / Utility screen, select Step 3 Initialization and Learning.

  15. Press the Next key.

  16. C114380E01
    Select the appropriate operation.

    HINT:
    1. Initialization of clutch: when removing and installing the following parts related to the clutch system.
      Clutch actuator, clutch stroke sensor, clutch disc and clutch cover, clutch release bearing, clutch release fork or fork lever, flywheel.
    2. Initialization of transmission: when removing and installing the parts related to the shift and select operation of the transmission assembly.
    3. Initialization of ECU: This initializes learned values of both the clutch and transmission.

  17. Press the Next key.

  18. C114381E01
    Read the information.

  19. Press the Next key after turning the ignition switch off.

  20. C114382
    Wait 10 seconds.

    HINT:
    Count down the seconds from 10 to 0.

  21. C114383E01
    Read the information.

  22. Press the Next key after turning the ignition switch on (IG).

  23. C114384
    Wait 40 seconds.

    HINT:
    Count down the seconds from 40 to 0.

  24. C114385E01
    Press the Exit key.

  25. Complete Initialization and Learning.

  26. Turn the intelligent tester OFF and turn the ignition switch off.

  27. Wait at least 20 seconds.

  28. Turn the ignition switch on (IG).

  29. Depress the brake pedal with the shift lever position in the N position.

  30. Start the engine and wait at least 10 seconds.

  31. Shift the gear from neutral to any other position.

    HINT:
    1. When [Initialization of transmission] was selected at step (p), add the following step between steps (w) and (x).
      Additional step: (w') Wait at least 30 seconds.
    2. If the Initialization and Learning operations fail, perform the operations again from step (a) more than 15 seconds after turning the ignition switch off.
    3. Perform Synchronization Position Calibration after performing Initialization of transmission or Initialization of ECU.
    4. Shifting the gear from neutral to any other position at last, the transmission control ECU learns the standby point. At this time, the value of Learn-Clutch Standby Point in the Data List changes from [Notexec] to [Exec].


INITIALIZATION OF MULTI-MODE MANUAL TRANSMISSION SYSTEM WITHOUT USING INTELLIGENT TESTER

HINT:
  1. The learning values and the DTC history of the multi-mode manual transmission system are stored in the EEPROM in the transmission control ECU. The stored information is not cleared even when the negative terminal of the battery is disconnected. To clear all the stored information, initialize the transmission control ECU.
  2. If the initialization of the multi-mode manual transmission system fails, perform the operation again from step (a) more than 15 seconds after turning the ignition switch off.
  3. If the initialization cannot be performed normally, there may be a malfunction in the shift lever position sensor, NE signals, or CAN communication.
  4. When replacing the following parts, proceed with the operations in the order listed in the table below.

Parts installed
Operation order
See procedure
  1. Transmission assembly
  2. Transmission parts (inside gear box)
  3. Transmission control ECU
1. INITIALIZATION OF MULTI-MODE MANUAL TRANSMISSION SYSTEM
[Initialization of ECU]
See below
2. LEARNING OF MULTI-MODE MANUAL TRANSMISSION SYSTEM
See below
3. SYNCHRONIZATION POSITION CALIBRATION
Click here
  1. Shift and select actuator
  2. Shift stroke sensor
  3. Select stroke sensor
1. INITIALIZATION OF MULTI-MODE MANUAL TRANSMISSION SYSTEM
[Initialization of transmission]
See below
2. LEARNING OF MULTI-MODE MANUAL TRANSMISSION SYSTEM
See below
3. SYNCHRONIZATION POSITION CALIBRATION
Click here
  1. Clutch actuator
  2. Clutch stroke sensor
  3. Clutch disc and clutch cover
  4. Clutch release bearing
  5. Clutch release fork
  6. Flywheel
  7. End plate
  8. Crankshaft
1. INITIALIZATION OF MULTI-MODE MANUAL TRANSMISSION SYSTEM
[Initialization of clutch]
See below
2. LEARNING OF MULTI-MODE MANUAL TRANSMISSION SYSTEM
See below
  1. Prepare the vehicle:

    1. Stop the vehicle.
    2. Shift the shift lever to the N position.
    3. Turn the ignition switch off.

  2. F100115E02
    Using SST, connect terminals TC and CG of the DLC3.
    SST
    09843-18040  

  3. Wait at least 10 seconds.

  4. Turn the ignition switch on (IG).

  5. BR03890
    Depress the brake pedal at least 7 times within 3 seconds.

    1. The buzzer sounds twice with an interval of 0.25 seconds.

  6. Depress the brake pedal.

  7. Shift the shift lever in the following sequence with the brake pedal depressed.

    1. When initializing the ECU: N → E → M → - → M → - → M → - → M → - → E → N.
    2. When initializing the clutch: N → E → M → + → M → - → M → + → M → - → E → N.
    3. When initializing the transmission: N → E → M → - → M → - → M → + → M → + → E → N.
    C127398E01

  8. Release the brake pedal

  9. BR03890
    Depress the brake pedal once.

    1. The buzzer sounds at intervals of 0.5 seconds as follows (an interval of 2.5 seconds exists between each cycle).

      1. Twice when initializing the ECU (one cycle)
      2. Three times when initializing the clutch (one cycle)
      3. Four times when initializing the transmission (one cycle)

      HINT:
      1. If the buzzer does not sound as specified, wait at least 15 seconds after turning the ignition switch off. Then, perform the procedure from step (a) again.
      2. If the buzzer sounds at intervals of 1 second (not at intervals of 0.5 seconds), wait at least 15 seconds after turning the ignition switch off. Then, perform the procedure from step (a) again.

  10. Depress the brake pedal 3 times or more within 2 seconds.

    1. The buzzer sounds twice with an interval of 0.25 seconds.

  11. Turn the ignition switch off and wait at least 10 seconds.

  12. The initialization is complete.

  13. Disconnect the SST from terminals TC and CG of the DLC3.


LEARNING OF MULTI-MODE MANUAL TRANSMISSION SYSTEM WITHOUT USING INTELLIGENT TESTER

HINT:
  1. Perform the procedure below to ensure that the initialized transmission control ECU stores the adjusted clutch position or gear position.
  2. If the learning of the multi-mode manual transmission system fails, perform the operation again from step (a) more than 15 seconds after turning the ignition switch off.

  1. Prepare the vehicle:

    1. Stop the vehicle.
    2. Shift the shift lever to the N position.
    3. Turn the ignition switch off.

  2. Turn the ignition switch on (IG).

  3. Wait at least 40 seconds.

  4. Start the engine under the following conditions:

    1. Shift lever is in the N position.
    2. Brake pedal is depressed.

    HINT:
    The shift N position indicator blinks when the engine starts.

  5. Wait at least 10 seconds.

  6. The learning is complete.

← HOW TO PROCEED WITH TROUBLESHOOTING (from Nov 2005)CALIBRATION (from Nov 2005) →