2005-2008 Yaris · Service Manual COMMUNICATION SYSTEM

Check CAN Bus Line (RHD Models)

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

When any DTC for the CAN communication system is output, first measure the resistance between the terminals of the DLC3 to specify the trouble area, and check that there is no short in the CAN main wire, between the main wire, to +B, or to GND.

WIRING DIAGRAM

C132284E01
C132285E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

    HINT:
    Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. CHECK CAN BUS WIRE (MAIN WIRE FOR DISCONNECTION, CAN BUS LINES FOR SHORT CIRCUIT)

  1. C118856E31
    Turn the ignition switch off.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D15-6 (CANH) - D15-14 (CANL)
    Ignition switch off
    54 to 69 Ω
    OK
    D15-6 (CANH) - D15-14 (CANL)
    Ignition switch off
    69 Ω or higher
    NG-A
    D16-6 (CANH) - D15-14 (CANL)
    Ignition switch off
    54 Ω or less
    NG-B



NG-A
CHECK CAN MAIN WIRE FOR DISCONNECTION

NG-B
CHECK CAN BUS LINES FOR SHORT CIRCUIT
OK


2. CHECK CAN BUS LINE FOR SHORT TO +B

  1. C118856E32
    Measure the resistance.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D15-6 (CANH) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D15-14 (CANL) - D15-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    D15-6 (CANH) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    D15-6 (CANH) - D15-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
CHECK CAN BUS LINE FOR SHORT TO +B
OK


3. CHECK CAN BUS LINE FOR SHORT TO GND

  1. C118856E33
    Measure the resistance.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D15-6 (CANH) - D15-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    D15-14 (CANL) - D15-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    D15-6 (CANH) - D15-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    D15-14 (CANL) - D15-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG



NG
CHECK CAN BUS LINE FOR SHORT TO GND
OK

HOW TO PROCEED WITH TROUBLESHOOTING


← Check CAN Bus Line (LHD Models) (from Aug 2005)Check CAN Bus Lines for Short Circuit (LHD Models) (from Aug 2005) →