2005-2008 Yaris · Service Manual COMMUNICATION SYSTEM

Check CAN Bus Lines for Short Circuit (LHD Models)

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

There may a short circuit in the CAN main wire and/or CAN branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54Ω.
Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 below 54Ω
  1. Short between CAN bus lines
  2. Brake actuator (skid control ECU)*1
  3. ABS and traction actuator (skid control ECU)*2
  4. Power steering ECU
  5. Steering sensor*2
  6. Yaw rate sensor*3
  7. ECM
  8. Center airbag sensor assembly
  9. Air conditioning amplifier*4
  10. Combination meter ECU
  11. Main body ECU
  12. Certification ECU*5
  13. D-CAN J/C (Junction connector)
  14. P-CAN J/C (Junction connector)

HINT:
  1. *1: w/ ABS
  2. *2: w/ VSC
  3. *3: w/ VSC (TMC Made)
  4. *4: w/ Air conditioning or PTC heater
  5. *5: w/ Entry and start system


WIRING DIAGRAM

C132277E01
C132278E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

    HINT:
    Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. CHECK CAN BUS LINES FOR SHORT CIRCUIT (DLC3 BRANCH WIRE)

  1. G100291E26
    Turn the ignition switch off.

  1. Disconnect the D41 D-CAN J/C connector.

  1. G026206E69
    Measure the resistance.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D15-6 (CANH) - D15-14 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    D15-6 (CANH) - D15-14 (CANL)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
OK


2. CONNECT CONNECTOR
  1. Reconnect the D-CAN J/C connector.


NEXT


3. CHECK CAN BUS LINES FOR SHORT CIRCUIT (P-CAN J/C SIDE)

  1. G100291E27
    Turn the ignition switch off.

  1. Disconnect the D42 P-CAN J/C connector.

  1. G026206E69
    Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D15-6 (CANH) - D15-14 (CANL)
    Ignition switch off
    108 to 132 Ω



OK
Go to step 18
NG


4. CHECK CAN BUS LINES FOR SHORT CIRCUIT (D-CAN J/C - P-CAN J/C)

  1. C125896E22
    Turn the ignition switch off.

  1. Disconnect the D41 D-CAN J/C connector.

  1. Measure the resistance.

    HINT:
    The resistance must be measured after the D42 P-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D41-11 (TORH) - D41-22 (TORH)
    Ignition switch off
    1 Ω or higher
    OK
    D41-11 (TORH) - D41-22 (TORH)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (D-CAN J/C - P-CAN J/C (CAN-H, CAN-L))
OK


5. CONNECT CONNECTOR
  1. Reconnect the P-CAN J/C connector.


NEXT


6. CHECK CAN BUS LINES FOR SHORT CIRCUIT (D-CAN J/C - ECM)

  1. C125896E23
    Measure the resistance.

    HINT:
    The resistance must be measured after the D41 D-CAN J/C connector is disconnected.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D41-4 (EFI) - D41-15 (EFI)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 12
OK


7. CHECK CAN BUS LINES FOR SHORT CIRCUIT (D-CAN J/C - BRAKE ACTUATOR (SKID CONTROL ECU))

NOTICE:
For vehicles without ABS, go to step 8.

  1. C125896E24
    Measure the resistance.

    HINT:
    The resistance must be measured after the D41 D-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D41-1 (ABS) - D41-12 (ABS)
    Ignition switch off
    Below 1 Ω
    A
    D41-1 (ABS) - D41-12 (ABS)
    Ignition switch off
    1 Ω or higher
    B



A
Go to step 13
B


8. CHECK CAN BUS LINES FOR SHORT CIRCUIT (D-CAN J/C - ABS AND TRACTION ACTUATOR (SKID CONTROL ECU))

NOTICE:
For vehicles without VSC, go to step 9.

  1. C125896E24
    Measure the resistance.

    HINT:
    The resistance must be measured after the D41 D-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D41-1 (ABS) - D41-12 (ABS)
    Ignition switch off
    Below 1 Ω
    A
    D41-1 (ABS) - D41-12 (ABS)
    Ignition switch off
    1 Ω or higher
    B



A
Go to step 14
B


9. CHECK CAN BUS LINES FOR SHORT CIRCUIT (D-CAN J/C - STEERING SENSOR)

NOTICE:
For vehicles without VSC, go to step 10.

  1. C125896E25
    Measure the resistance.

    HINT:
    The resistance must be measured after the D41 D-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D41-2 (STR) - D41-13 (STR)
    Ignition switch off
    Below 1 Ω
    A
    D41-2 (STR) - D41-13 (STR)
    Ignition switch off
    1 Ω or higher
    B



A
Go to step 15
B


10. CHECK CAN BUS LINES FOR SHORT CIRCUIT (D-CAN J/C - AIR CONDITIONING AMPLIFIER)

NOTICE:
For vehicles without air conditioning or PTC heater, go to step 11.

  1. C125896E26
    Measure the resistance.

    HINT:
    The resistance must be measured after the D41 D-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D41-6 (A/C) - D41-17 (A/C)
    Ignition switch off
    Below 1 Ω
    A
    D41-6 (A/C) - D41-17 (A/C)
    Ignition switch off
    1 Ω or higher
    B



A
Go to step 16
B


11. CHECK CAN BUS LINES FOR SHORT CIRCUIT (D-CAN J/C - CENTER AIRBAG SENSOR ASSEMBLY)

  1. C125896E27
    Measure the resistance.

    HINT:
    The resistance must be measured after the D41 D-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D41-8 (A/B) - D41-19 (A/B)
    Ignition switch off
    Below 1 Ω
    A
    D41-8 (A/B) - D41-19 (A/B)
    Ignition switch off
    1 Ω or higher
    B



A
Go to step 17
B

REPLACE D-CAN J/C (JUNCTION CONNECTOR)

12. CHECK CAN BUS LINES FOR SHORT CIRCUIT (ECM MAIN WIRE)

  1. C125895E08
    1NZ / 2NZ / 2SZ-FE engine:
    1. Disconnect the A21 ECM connector.

    2. C125896E23
      Measure the resistance.

      HINT:
      The resistance must be measured after the D41 D-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D41-4 (EFI) - D41-15 (EFI)
      Ignition switch off
      1 Ω or higher
      OK
      D41-4 (EFI) - D41-15 (EFI)
      Ignition switch off
      Below 1 Ω
      NG

  1. C118186E05
    1KR-FE engine:
    1. Disconnect the A31 ECM connector.

    2. C125896E23
      Measure the resistance.

      HINT:
      The resistance must be measured after the D41 D-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D41-4 (EFI) - D41-15 (EFI)
      Ignition switch off
      1 Ω or higher
      OK
      D41-4 (EFI) - D41-15 (EFI)
      Ignition switch off
      Below 1 Ω
      NG

  1. C130899E05
    1ND-TV engine:
    1. Disconnect the A49 ECM connector.

    2. C125896E23
      Measure the resistance.

      HINT:
      The resistance must be measured after the D41 D-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D41-4 (EFI) - D41-15 (EFI)
      Ignition switch off
      1 Ω or higher
      OK
      D41-4 (EFI) - D41-15 (EFI)
      Ignition switch off
      Below 1 Ω
      NG



OK
REPLACE ECM
NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CAN-H, CAN-L)

13. CHECK CAN BUS LINES FOR SHORT CIRCUIT (BRAKE ACTUATOR (SKID CONTROL ECU) BRANCH WIRE)

  1. C118165E05
    TMC Made:
    1. Disconnect the A15 brake actuator (skid control ECU) connector.

    2. C125896E24
      Measure the resistance.

      HINT:
      The resistance must be measured after the D41 D-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D41-1 (ABS) - D41-12 (ABS)
      Ignition switch off
      1 Ω or higher
      OK
      D41-1 (ABS) - D41-12 (ABS)
      Ignition switch off
      Below 1 Ω
      NG

  1. C130880E10
    TMMF Made:
    1. Disconnect the A39 brake actuator (skid control ECU) connector.

    2. C125896E24
      Measure the resistance.

      HINT:
      The resistance must be measured after the D41 D-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D41-1 (ABS) - D41-12 (ABS)
      Ignition switch off
      1 Ω or higher
      OK
      D41-1 (ABS) - D41-12 (ABS)
      Ignition switch off
      Below 1 Ω
      NG



OK
REPLACE BRAKE ACTUATOR (SKID CONTROL ECU)
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BRAKE ACTUATOR (SKID CONTROL ECU) (CAN-H, CAN-L)

14. CHECK CAN BUS LINES FOR SHORT CIRCUIT (ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) BRANCH WIRE)

  1. C118187E04
    TMC Made:
    1. Disconnect the A31 ABS and traction actuator (skid control ECU) connector.

    2. C125896E24
      Measure the resistance.

      HINT:
      The resistance must be measured after the D41 D-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D41-1 (ABS) - D41-12 (ABS)
      Ignition switch off
      1 Ω or higher
      OK
      D41-1 (ABS) - D41-12 (ABS)
      Ignition switch off
      Below 1 Ω
      NG

  1. C130880E08
    TMMF Made:
    1. Disconnect the A39 ABS and traction actuator (skid control ECU) connector.

    2. C125896E24
      Measure the resistance.

      HINT:
      The resistance must be measured after the D41 D-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D41-1 (ABS) - D41-12 (ABS)
      Ignition switch off
      1 Ω or higher
      OK
      D41-1 (ABS) - D41-12 (ABS)
      Ignition switch off
      Below 1 Ω
      NG



OK
REPLACE ABS AND TRACTION ACTUATOR (SKID CONTROL ECU)
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) (CAN-H, CAN-L)

15. CHECK CAN BUS LINES FOR SHORT CIRCUIT (STEERING SENSOR BRANCH WIRE)

  1. G030155E27
    Disconnect the D62 steering sensor connector.

  1. C125896E25
    Measure the resistance.

    HINT:
    The resistance must be measured after the D41 D-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D41-2 (STR) - D41-13 (STR)
    Ignition switch off
    1 Ω or higher
    OK
    D41-2 (STR) - D41-13 (STR)
    Ignition switch off
    Below 1 Ω
    NG



OK
REPLACE STEERING SENSOR
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING SENSOR (CAN-H, CAN-L)

16. CHECK CAN BUS LINES FOR SHORT CIRCUIT (AIR CONDITIONING AMPLIFIER BRANCH WIRE)

  1. G100279E05
    w/ Auto air conditioning:
    1. Disconnect the E11 air conditioning amplifier connector.

    2. C125896E26
      Measure the resistance.

      HINT:
      The resistance must be measured after the D41 D-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D41-6 (A/C) - D41-17 (A/C)
      Ignition switch off
      1 Ω or higher
      OK
      D41-6 (A/C) - D41-17 (A/C)
      Ignition switch off
      Below 1 Ω
      NG

  1. C131847E04
    w/ Manual air conditioning:
    1. Disconnect the E8 air conditioning amplifier connector.

    2. C125896E26
      Measure the resistance.

      HINT:
      The resistance must be measured after the D41 D-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D41-6 (A/C) - D41-17 (A/C)
      Ignition switch off
      1 Ω or higher
      OK
      D41-6 (A/C) - D41-17 (A/C)
      Ignition switch off
      Below 1 Ω
      NG



OK
REPLACE AIR CONDITIONING AMPLIFIER
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CAN-H, CAN-L)

17. CHECK CAN BUS LINES FOR SHORT CIRCUIT (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE)

  1. C131069E01
    Disconnect the D16 center airbag sensor assembly connector.

  1. C125896E27
    Measure the resistance.

    HINT:
    The resistance must be measured after the D41 D-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D41-8 (A/B) - D41-19 (A/B)
    Ignition switch off
    1 Ω or higher
    OK
    D41-8 (A/B) - D41-19 (A/B)
    Ignition switch off
    Below 1 Ω
    NG



OK
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CAN-H, CAN-L)

18. CHECK CAN BUS LINES FOR SHORT CIRCUIT (P-CAN J/C - POWER STEERING ECU)

  1. C125896E28
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 P-CAN J/C connector is disconnected.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D42-4 (EPS) - D42-15 (EPS)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 23
OK


19. CHECK CAN BUS LINES FOR SHORT CIRCUIT (P-CAN J/C - MAIN BODY ECU)

  1. C125896E29
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 P-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-5 (J/B) - D42-16 (EPS)
    Ignition switch off
    Below 1 Ω
    A
    D42-5 (J/B) - D42-16 (EPS)
    Ignition switch off
    1 Ω or higher
    B



A
Go to step 24
B


20. CHECK CAN BUS LINES FOR SHORT CIRCUIT (P-CAN J/C - YAW RATE SENSOR)

NOTICE:
For vehicles without VSC (TMC made), go to step 21.

  1. C125896E30
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 P-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-2 (YAW) - D42-13 (YAW)
    Ignition switch off
    Below 1 Ω
    A
    D42-2 (YAW)- D42-13 (YAW)
    Ignition switch off
    1 Ω or higher
    B



A
Go to step 25
B


21. CHECK CAN BUS LINES FOR SHORT CIRCUIT (P-CAN J/C - CERTIFICATION ECU)

NOTICE:
For vehicles without entry and start system, go to step 22.

  1. C125896E31
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 P-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-6 (SMRT) - D42-17 (SMRT)
    Ignition switch off
    Below 1 Ω
    A
    D42-6 (SMRT) - D42-17 (SMRT)
    Ignition switch off
    1 Ω or higher
    B



A
Go to step 26
B


22. CHECK CAN BUS LINES FOR SHORT CIRCUIT (P-CAN J/C - COMBINATION METER ECU)

  1. C125896E32
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 P-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-7 (MET) - D42-18 (MET)
    Ignition switch off
    Below 1 Ω
    A
    D42-7 (MET) - D42-18 (MET)
    Ignition switch off
    1 Ω or higher
    B



A
Go to step 27
B

REPLACE P-CAN J/C (JUNCTION CONNECTOR)

23. CHECK CAN BUS LINES FOR SHORT CIRCUIT (POWER STEERING ECU MAIN WIRE)

  1. G100242E11
    Disconnect the D31 power steering ECU connector.

  1. C125896E28
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 P-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-4 (EPS) - D42-15 (EPS)
    Ignition switch off
    1 Ω or higher
    OK
    D42-4 (EPS) - D42-15 (EPS)
    Ignition switch off
    Below 1 Ω
    NG



OK
REPLACE POWER STEERING ECU
NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO POWER STEERING ECU (CAN-H, CAN-L)

24. CHECK CAN BUS LINES FOR SHORT CIRCUIT (MAIN BODY ECU BRANCH WIRE)

  1. C131839E02
    w/ Entry and start system:
    1. Disconnect the D66 main body ECU connector.

    2. C125896E29
      Measure the resistance.

      HINT:
      The resistance must be measured after the D42 P-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D42-6 (J/B) - D42-17 (J/B)
      Ignition switch off
      1 Ω or higher
      OK
      D42-6 (J/B) - D42-17 (J/B)
      Ignition switch off
      Below 1 Ω
      NG

  1. C131840E02
    w/o Entry and start system:
    1. Disconnect the D33 main body ECU connector.

    2. C125896E29
      Measure the resistance.

      HINT:
      The resistance must be measured after the D42 P-CAN J/C connector is disconnected.

      Result:
      Tester Connection
      Condition
      Specified Condition
      Proceed to
      D42-6 (J/B) - D42-17 (J/B)
      Ignition switch off
      1 Ω or higher
      OK
      D42-6 (J/B) - D42-17 (J/B)
      Ignition switch off
      Below 1 Ω
      NG



OK
REPLACE MAIN BODY ECU
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CAN-H, CAN-L)

25. CHECK CAN BUS LINES FOR SHORT CIRCUIT (YAW RATE SENSOR BRANCH WIRE)

  1. C125957E04
    Disconnect the D63 yaw rate sensor connector.

  1. C125896E30
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 P-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-2 (YAW) - D42-13 (YAW)
    Ignition switch off
    1 Ω or higher
    OK
    D42-2 (YAW) - D42-13 (YAW)
    Ignition switch off
    Below 1 Ω
    NG



OK
REPLACE YAW RATE SENSOR
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CAN-H, CAN-L)

26. CHECK CAN BUS LINES FOR SHORT CIRCUIT (CERTIFICATION ECU BRANCH WIRE)

  1. G100280E05
    Disconnect the D63 certification ECU connector.

  1. C125896E31
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 P-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-6 (SMRT) - D42-17 (SMRT)
    Ignition switch off
    1 Ω or higher
    OK
    D42-6 (SMRT) - D42-17 (SMRT)
    Ignition switch off
    Below 1 Ω
    NG



OK
REPLACE CERTIFICATION ECU
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CAN-H, CAN-L)

27. CHECK CAN BUS LINES FOR SHORT CIRCUIT (COMBINATION METER ECU BRANCH WIRE)

  1. C139156E04
    Disconnect the D63 combination meter ECU connector.

  1. C125896E32
    Measure the resistance.

    HINT:
    The resistance must be measured after the D42 P-CAN J/C connector is disconnected.

    Result:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D42-7 (MET) - D42-18 (MET)
    Ignition switch off
    1 Ω or higher
    OK
    D42-7 (MET) - D42-18 (MET)
    Ignition switch off
    Below 1 Ω
    NG



OK
REPLACE COMBINATION METER ECU
NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO COMBINATION METER ECU (CAN-H, CAN-L)


← Check CAN Bus Line (RHD Models) (from Aug 2005)Check CAN Bus Lines for Short Circuit (RHD Models) (from Aug 2005) →