2005-2008 Yaris · Service Manual BODY ELECTRICAL

Only Driver Door LOCK / UNLOCK Functions do not Operate

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

The main body ECU receives lock/unlock switch signals and activates the door lock motor accordingly.

WIRING DIAGRAM

B109873E15

INSPECTION PROCEDURE


1. INSPECT FRONT DOOR LOCK ASSEMBLY (DRIVER SIDE)

  1. B079551E05
    LHD:
    1. Apply the battery voltage to the door lock motor and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      Lock
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      Unlock

  1. B118056E04
    RHD:

    1. B118058E03
      Apply the battery voltage to the door lock motor and check the operation of the door lock motor.

      OK:
      w/ Double locking system 
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1
      Lock
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 2
      Unlock
      w/o Double locking system 
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      Lock
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      Unlock



NG
REPLACE FRONT DOOR LOCK ASSEMBLY (DRIVER SIDE)
OK


2. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DRIVER SIDE FRONT DOOR LOCK ASSEMBLY)

  1. B146194E01
    LHD:
    1. Disconnect the 4H main body ECU connector.

    2. Disconnect the G5 door lock connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      4H-17 (ACT+) - G5-4 (L)
      Below 1 Ω
      4H-9 (ACT-) - G5-1 (UL)
      Below 1 Ω
      4H-17 (ACT+) or G5-4 (L) - Body ground
      10 kΩ or higher
      4H-9 (ACT-) or G5-1 (UL) - Body ground
      10 kΩ or higher

    4. Reconnect the main body ECU connector.

    5. Reconnect the door lock connector.

  1. RHD:

    1. Disconnect the and 4H main body ECU connector.

    2. Disconnect the F5 door lock connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      w/ Double locking system 
      Tester Connection
      Specified Condition
      4H-8 (ACT+) - F5-2 (L)
      Below 1 Ω
      4H-18 (ACT-) - F5-1 (UL)
      Below 1 Ω
      4H-8 (ACT+) or F5-2 (L) - Body ground
      10 kΩ or higher
      4H-18 (ACT-) or F5-1 (UL) - Body ground
      10 kΩ or higher
      w/o Double locking system 
      Tester Connection
      Specified Condition
      4H-8 (ACT+) - F5-4 (L)
      Below 1 Ω
      4H-18 (ACT-) - F5-1 (UL)
      Below 1 Ω
      4H-8 (ACT+) or F5-4 (L) - Body ground
      10 kΩ or higher
      4H-18 (ACT-) or F5-1 (UL) - Body ground
      10 kΩ or higher

    4. Reconnect the main body ECU connector.

    5. Reconnect the door lock connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← All Doors cannot be Locked / Unlocked Simultaneously (from Aug 2005)Only Passenger Door LOCK / UNLOCK Functions do not Operate (from Aug 2005) →