All Doors cannot be Locked / Unlocked Simultaneously
Circuit diagnosis · Vehicles built from Aug 2005
DESCRIPTION
The main body ECU receives switch signals from the door control switch (for front driver door side), door control switch (for center console side*), driver side door key cylinder, front passenger side door key cylinder (w/o entry and start system) and front passenger side door lock switch, and activates the door lock motor on each door accordingly.*: Hatchback
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. INSPECT FRONT DOOR LOCK ASSEMBLY (DRIVER SIDE) |
Apply the battery voltage to the door lock motor and measure the resistance.

- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
8 (LSSR) - 7 (E)
Battery positive (+) → Terminal 1 - Battery negative (-) → Terminal 4
Below 1 Ω
8 (LSSR) - 7 (E)
Battery positive (+) → Terminal 4 - Battery negative (-) → Terminal 1
10 kΩ or higher
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT DOOR LOCK ASSEMBLY (DRIVER SIDE)) |
Disconnect the D33 main body ECU connector.

Disconnect the G5 door lock connector.
Measure the resistance
- Standard resistance:
Tester Connection
Specified Condition
D33-21 (LSWD) - G5-8 (LSSR)
Below 1 Ω
D33-21 (LSWD) or G5-8 (LSSR) - Body ground
10 kΩ or higher
Reconnect the main body ECU connector.
Reconnect the door lock connector.
|
|
||||
| OK | |
| 3. CHECK DOOR LOCK OPERATION |
Proceed to the next step according to the symptom listed in the table below.
- Result:
Symptom
Proceed to
Doors cannot be locked using door control switch (for front driver door side)
A
Doors cannot be locked using driver side door key cylinder
B
Doors cannot be locked using door control switch (for center console side)*
C
Doors cannot be locked using front passenger side door key cylinder
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 4. INSPECT DOOR CONTROL SWITCH (for Front Driver Door Side) |
![]() ![]() |
LHD:
Disconnect the G1 door control switch (for front driver door side) connector.
Measure the resistance of the switch.
- Standard resistance (3 Door w/ Jam protection function):
Tester Connection
Switch Condition
Specified Condition
3 (L) - 7 (E)
Lock
Below 1 Ω
9 (UL) - 7 (E)
Unlock
Below 1 Ω
3 (L) - 7 (E)
OFF
10 kΩ or higher
9 (UL) - 7 (E)
OFF
10 kΩ or higher
- Standard resistance (3 Door w/o Jam protection function):
Tester Connection
Switch Condition
Specified Condition
1 (L) - 7 (E)
Lock
Below 1 Ω
9 (UL) - 7 (E)
Unlock
Below 1 Ω
1 (L) - 7 (E)
OFF
10 kΩ or higher
9 (UL) - 7 (E)
OFF
10 kΩ or higher
- Standard resistance (5 Door and Sedan):
Tester Connection
Switch Condition
Specified Condition
2 (L) - 1 (E)
Lock
Below 1 Ω
9 (UL) - 1 (E)
Unlock
Below 1 Ω
2 (L) - 1 (E)
OFF
10 kΩ or higher
9 (UL) - 1 (E)
OFF
10 kΩ or higher
Reconnect the door control switch (for front driver door side) connector.
RHD:

Disconnect the F7 door control switch (for front driver door side) connector.
Measure the resistance of the switch.
- Standard resistance (3 Door w/ Jam protection function):
Tester Connection
Switch Condition
Specified Condition
1 (L) - 7 (E)
Lock
Below 1 Ω
3 (UL) - 7 (E)
Unlock
Below 1 Ω
1 (L) - 7 (E)
OFF
10 kΩ or higher
3 (UL) - 7 (E)
OFF
10 kΩ or higher
- Standard resistance (3 Door w/o Jam protection function):
Tester Connection
Switch Condition
Specified Condition
1 (L) - 7 (E)
Lock
Below 1 Ω
9 (UL) - 7 (E)
Unlock
Below 1 Ω
1 (L) - 7 (E)
OFF
10 kΩ or higher
9 (UL) - 7 (E)
OFF
10 kΩ or higher
- Standard resistance (5 Door and Sedan):
Tester Connection
Switch Condition
Specified Condition
1 (L) - 9 (E)
Lock
Below 1 Ω
8 (UL) - 9 (E)
Unlock
Below 1 Ω
1 (L) - 9 (E)
OFF
10 kΩ or higher
8 (UL) - 9 (E)
OFF
10 kΩ or higher
Reconnect the door control switch (for front driver door side) connector.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL SWITCH (Front Driver Door Side)) |
![]() ![]() |
LHD:
Disconnect the 4H main body ECU connector.
Disconnect the G1 door control switch (for front driver door side) connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance (3 Door w/ Jam protection function):
Tester Connection
Specified Condition
4H-5 (UL1) - G1-9 (UL)
Below 1 Ω
4H-4 (L1) - G1-3 (L)
Below 1 Ω
4H-5 (UL1) or G1-9 (UL) - Body ground
10 kΩ or higher
4H-4 (L1) or G1-3 (L) - Body ground
10 kΩ or higher
- Standard resistance (3 Door w/o Jam protection function):
Tester Connection
Specified Condition
4H-5 (UL1) - G1-9 (UL)
Below 1 Ω
4H-4 (L1) - G1-1 (L)
Below 1 Ω
4H-5 (UL1) or G1-9 (UL) - Body ground
10 kΩ or higher
4H-4 (L1) or G1-1 (L) - Body ground
10 kΩ or higher
- Standard resistance (5 Door and Sedan):
Tester Connection
Specified Condition
4H-5 (UL1) - G1-9 (UL)
Below 1 Ω
4H-4 (L1) - G1-2 (L)
Below 1 Ω
4H-5 (UL1) or G1-9 (UL) - Body ground
10 kΩ or higher
4H-4 (L1) or G1-2 (L) - Body ground
10 kΩ or higher
Reconnect the main body ECU connector.
Reconnect the door control switch (for front driver door side) connector.
RHD:

Disconnect the 4H main body ECU connector.
Disconnect the F7 door control switch (for front driver door side) connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance (3 Door w/ Jam protection function):
Tester Connection
Specified Condition
4H-5(UL1) - F7-3 (UL)
Below 1 Ω
4H-4 (L1) - F7-1(L)
Below 1 Ω
4H-5 (UL1) or F7-3 (UL) - Body ground
10 kΩ or higher
4H-4 (L1) or F7-1 (L) - Body ground
10 kΩ or higher
- Standard resistance (3 Door w/o Jam protection function):
Tester Connection
Specified Condition
4H-5 (UL1) - F7-9 (UL)
Below 1 Ω
4H-4 (L1) - F7-1 (L)
Below 1 Ω
4H-5 (UL1) or F7-9 (UL) - Body ground
10 kΩ or higher
4H-4 (L1) or F7-1 (L) - Body ground
10 kΩ or higher
- Standard resistance (5 Door and Sedan):
Tester Connection
Specified Condition
4H-5 (UL1) - F7-8 (UL)
Below 1 Ω
4H-4 (L1) - F7-1 (L)
Below 1 Ω
4H-5 (UL1) or F7-8 (UL) - Body ground
10 kΩ or higher
4H-4 (L1) or F7-1 (L) - Body ground
10 kΩ or higher
Reconnect the main body ECU connector.
Reconnect the door control switch (for front driver door side) connector.
|
|
||||
| OK | ||
| ||
| 6. READ VALUE OF INTELLIGENT TESTER (DOR KEY SW-LOCK, DOR KEY SW-ULOCK) |
Check the DATA LIST to ensure the proper operation of the door lock and unlock switch.
- Main Body ECU:
Item
Measurement Item/Display (Range)
Normal Condition
Diagnostic Note
Dor Key SW-Lock
Door key-linked lock switch signal/ ON or OFF
ON: Door key cylinder is turned to lock position
OFF: Driver side door key cylinder is turned to unlock position
-
- Main Body ECU:
Item
Measurement Item/Display (Range)
Normal Condition
Diagnostic Note
Dor Key SW-ULock
Door key-linked lock switch signal/ ON or OFF
ON: Door key cylinder is turned to unlock position
OFF: Door key cylinder is turned to lock position
-
- OK:
- ON (driver side door key cylinder is turned to lock/unlock position) appears on tester screen.
|
|
||||
| NG | |
| 7. CHECK HARNESS AND CONNECTOR (DRIVER SIDE DOOR LOCK ASSEMBLY - MAIN BODY ECU) |
![]() ![]() |
LHD:
Disconnect the 4H main body ECU connector.
Disconnect the G5 front door lock assembly connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
4H-6 (UL2) - G5-10 (UL)
Below 1 Ω
4H-7 (L2) - G5-9 (L)
Below 1 Ω
4H-6 (UL2) or G5-10(UL) - Body ground
10 kΩ or higher
4H-7 (L2) or G5-9 (L) - Body ground
10 kΩ or higher
Reconnect the main body ECU connector.
Reconnect the front door lock assembly connector.
RHD:

Disconnect the 4H main body ECU connector.
Disconnect the F5 front door lock assembly connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
4H-6 (UL2) - F5-5 (UL)
Below 1 Ω
4H-7 (L2) - F5-6 (L)
Below 1 Ω
4H-6 (UL2) or F5-5 (UL) - Body ground
10 kΩ or higher
4H-7 (L2) or F5-6 (L) - Body ground
10 kΩ or higher
Reconnect the main body ECU connector.
Reconnect the front door lock assembly connector.
|
|
||||
| OK | ||
| ||
| 8. INSPECT DOOR CONTROL SWITCH (for Center Console Side) |
![]() ![]() |
Disconnect the D30 door control switch (for center console side) connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Condition
Specified Condition
5 - 6
Lock
Below 1 Ω
4 - 6
Unlock
Below 1 Ω
5 - 6
OFF
Below 1 Ω
4 - 6
OFF
Below 1 Ω
Reconnect the door control switch (for center console side) connector.
|
|
||||
| OK | |
| 9. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL SWITCH (Center Console Side)) |
![]() ![]() |
Disconnect the 4C and 4E main body ECU connectors.
Disconnect the D30 door control switch (for center console side) connector.
Measure the resistance of the fuses.
- Standard resistance:
Tester Connection
Specified Condition
4C-10(UL1) - D30-4
Below 1 Ω
4E-11 (L1) - D30-5
Below 1 Ω
4C-10 (UL1) or D30-4 - Body ground
10 kΩ or higher
4E-11 (L1) or D30-5 - Body ground
10 kΩ or higher
Reconnect the main body ECU connector.
Reconnect the door control switch (for center console side) connector.
|
|
||||
| OK | ||
| ||
| 10. READ VALUE OF INTELLIGENT TESTER (DOR KEY SW-LOCK, DOR KEY SW-ULCK) |
Check the DATA LIST to ensure the proper operation of the door lock and unlock switch.
- Main Body ECU:
Item
Measurement Item/Display (Range)
Normal Condition
Diagnostic Note
Dor Key SW-Lock
Door key-linked lock switch signal/ ON or OFF
ON: Door key cylinder is turned to lock position
OFF: Driver side door key cylinder is turned to unlock position
-
- Main Body ECU:
Item
Measurement Item/Display (Range)
Normal Condition
Diagnostic Note
Dor Key SW-ULck
Door key-linked unlock switch signal/ ON or OFF
ON: Door key cylinder is turned to unlock position
OFF: Door key cylinder is turned to lock position
-
- OK:
- ON (driver side door key cylinder is turned to lock/unlock position) appears on screen.
|
|
||||
| NG | |
| 11. CHECK HARNESS AND CONNECTOR (PASSENGER SIDE DOOR LOCK ASSEMBLY - MAIN BODY ECU) |
![]() ![]() |
LHD:
Disconnect the 4H main body ECU connector.
Disconnect the F5 front door lock assembly connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
4H-15 (UL2) - F5-5 (UL)
Below 1 Ω
4H-16 (L2) - F5-6 (L)
Below 1 Ω
4H-15 (UL2) or F5-5 (UL) - Body ground
10 kΩ or higher
4H-16 (L2) or F5-6 (L) - Body ground
10 kΩ or higher
Reconnect the main body ECU connector.
Reconnect the front door lock assembly connector.
RHD:

Disconnect the 4H main body ECU connector.
Disconnect the G5 front door lock assembly connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
4H-15 (UL2) - G5-10 (UL)
Below 1 Ω
4H-16 (L2) - G5-9 (L)
Below 1 Ω
4H-15 (UL2) or G5-10(UL) - Body ground
10 kΩ or higher
4H-16 (L2) or G5-9 (L) - Body ground
10 kΩ or higher
Reconnect the main body ECU connector.
Reconnect the front door lock assembly connector.
|
|
||||
| OK | ||
| ||






