2005-2008 Yaris · Service Manual BODY ELECTRICAL

Only Rear Door RH LOCK / UNLOCK Functions do not Operate

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

The main body ECU receives lock/unlock switch signals and activates the door lock motor accordingly.

WIRING DIAGRAM

B109873E07

INSPECTION PROCEDURE


1. INSPECT REAR DOOR LOCK ASSEMBLY RH

  1. B107858E01
    LHD:
    1. Apply the battery voltage to the door lock motor and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      Lock
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      Unlock

  1. B079080E04
    B107858E02
    RHD:
    1. Apply the battery voltage to the door lock motor and check the operation of the door lock motor.

      OK:
      w/ Double locking system 
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 3
      Lock
      Battery positive (+) → Terminal 3
      Battery negative (-) → Terminal 4
      Unlock
      w/o Double locking system 
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      Lock
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      Unlock



NG
REPLACE REAR DOOR LOCK ASSEMBLY RH
OK


2. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REAR DOOR LOCK ASSEMBLY RH)
B123824E02
  1. LHD:

    1. Disconnect the 4A main body ECU connector.

    2. Disconnect the H3 door lock connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      4A-3 (ACT+) - H3-4
      Below 1 Ω
      4A-4 (ACT-) - H3-1
      Below 1 Ω
      4A-3 (ACT+) or H3-4 - Body ground
      10 kΩ or higher
      4A-4 (ACT-) or H3-1 - Body ground
      10 kΩ or higher

    4. Reconnect the main body ECU connector.

    5. Reconnect the door lock connector.

  1. RHD:

    1. Disconnect the 4A main body ECU connector.

    2. Disconnect the H3 door lock connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      w/ Double locking system 
      Tester Connection
      Specified Condition
      4A-3 (ACT+) - H3-4
      Below 1 Ω
      4A-4 (ACT-) - H3-3
      Below 1 Ω
      4A-3 (ACT+) or H3-4 - Body ground
      10 kΩ or higher
      4A-4 (ACT-) or H3-3 - Body ground
      10 kΩ or higher
      w/o Double locking system 
      Tester Connection
      Specified Condition
      4A-3 (ACT+) - H3-4
      Below 1 Ω
      4A-4 (ACT-) - H3-1
      Below 1 Ω
      4A-3 (ACT+) or H3-4 - Body ground
      10 kΩ or higher
      4A-4 (ACT-) or H3-1 - Body ground
      10 kΩ or higher

    4. Reconnect the main body ECU connector.

    5. Reconnect the door lock connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← Only Rear Door LH LOCK / UNLOCK Functions do not Operate (from Aug 2005)Only Back Door LOCK / UNLOCK Functions do not Operate (from Aug 2005) →