DATA LIST / ACTIVE TEST
System information · Vehicles built from Aug 2005
| DATA LIST |
- HINT:
- Using the Data List displayed by the intelligent tester, you can read the values of the switches, sensors, actuators and so on without parts removal. Reading the Data List as the first step of troubleshooting is one method of shortening labor time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn on the tester.
Select the following items: Powertrain / Engine and ECT / Data Test.
In accordance with the display on the tester, read the Data List.
Item
Measurement Item/
Range (display)
Normal Condition
Diagnostic Note
Vehicle Speed
Vehicle Speed display/
min.: 0 km/h (0 mph)
max.: 255 km/h (158 mph)
- Vehicle stopped:
0 km/h (0 mph)
- Same as speedometer reading
-
SPD (NT)
Input Turbine Speed/
display: 50 rpm
min.: 0 rpm
max.: 12750 rpm
- HINT:
- Lock-Up ON (After warming up engine):
Input turbine speed (NT) equal to engine speed
- Lock-Up OFF (Idling at P or N position):
Input turbine speed (NT) nearly equal to engine speed
- Vehicle stopped in D position: 0 rpm
- Lock-Up ON (After warming up engine):
-
Neutral Position SW Signal
PNP SW Status/
ON or OFF
Shift lever position;
P or N: ON
Except P and N: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts,
- Click here.
Stop Light Switch
Stop Light SW Status/
ON or OFF
- Brake pedal is depressed: ON
- Brake pedal is released: OFF
-
Shift Status
ECM Gearshift Command/
1st, 2nd, 3rd or 4th
Shift lever position; - L: 1st
- 2: 1st or 2nd
- 3: 1st, 2nd or 3rd
- D: 1st, 2nd, 3rd or 4th
-
Shift SW Status (R Range)
PNP SW Status/
ON or OFF
Shift lever position;
R: ON
Except R: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts,
- Click here.
Shift SW Status (P Range)
PNP SW Status/
ON or OFF
Shift lever position;
P: ON
Except P: OFF
Shift SW Status (N Range)
PNP SW Status/
ON or OFF
Shift lever position;
N: ON
Except N: OFF
Shift SW Status (D Range)
PNP SW Status/
ON or OFF
Shift lever position;
D or 3: ON
Except D and 3: OFF
Shift SW Status (3 Range)
PNP SW Status/
ON or OFF
Shift lever position;
3: ON
Except 3: OFF
-
Shift SW Status (2 Range)
PNP SW Status/
ON or OFF
Shift lever position;
2: ON
Except 2: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts,
- Click here.
Shift SW Status (L Range)
PNP SW Status/
ON or OFF
Shift lever position;
L: ON
Except L: OFF
A/T Oil Temperature 1
ATF (Automatic Transmission Fluid) Temperature Sensor Value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
- After Stall Test; Approximately 80°C (176°F)
- Equal to ambient temperature when cold soak
If value is -40°C (-40°F) or 150°C (302°F) or more, ATF temperature sensor circuit is open or short.
Lock Up
Lock Up Status/
ON or OFF
- Lock Up: ON
- Except Lock Up: OFF
-
Lock Up Solenoid Status
Lock Up Solenoid Status/
ON or OFF
- Lock up solenoid ON: ON
- Lock up solenoid OFF: OFF
-
ST Solenoid Status
Shift Solenoid ST Status/
ON or OFF
Up-shifting and down-shifting between 3rd and 4th gears while driving:
OFF → ON → OFF
-
SLT Solenoid Status
Shift Solenoid SLT Status/
ON or OFF
- Accelerator pedal is depressed: OFF
- Accelerator pedal is released: ON
-
- Vehicle stopped:
| ACTIVE TEST |
- HINT:
- Performing the Active Test using the intelligent tester allows the relay, VSV, actuator and so on to operate without parts removal. Performing the Active Test as the first step of troubleshooting is one method to shorten labor time.
- It is possible to display the Data List during the Active Test.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn on the tester.
Select the following items: Powertrain / Engine and ECT / Active Test.
In accordance with the display on the tester, perform the Active Test.
*: "Control the Line Pressure Up" in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transaxle, which is used in the HYDRAULIC TEST (Click here) as well.Item
Test Details
Diagnostic Note
Control the Line Pressure Up*
[Test Details]
Operate shift solenoid SLT and raise line pressure.
[Vehicle Condition]- Vehicle stopped
- IDL: ON
- HINT:
- OFF: Line pressure up (when active test of "Control the Line Pressure Up" is performed, ECM turns off SLT solenoid)
- ON: No action (normal operation)
-
Control the Lock Up
[Test Details]
Control shift solenoid SL to set automatic transaxle to lock-up condition.
[Vehicle Condition]
Vehicle Speed: 60 km/h (36 mph) or more, and 4th gear
Possible to check SL operation.
Control the Shift Position
[Test Details]
Operate shift solenoid valve and set each shift position.
[Vehicle Condition]- IDL: ON
- Less than 50 km/h (30 mph)
- Press "→" button: Shift up
- Press "←" button: Shift down
Possible to check operation of shift solenoid valves.
Activate the Solenoid (ST)
[Test Details]
Operate shift solenoid ST
[Vehicle Condition]- Vehicle Stopped
- IDL: ON
Possible to check ST operation.
- HINT:
- The pressure values in Active Test and HYDRAULIC TEST are different from each other.
- Vehicle stopped