2005-2008 Yaris · Service Manual TRANSMISSION

P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.
DTC No.
DTC Detection Condition
Trouble Area
P0705
(a) Any 2 or more of following signals are ON simultaneously. (2-trip detection logic)
  1. P input signal
  2. R input signal
  3. N input signal
  4. D input signal
  5. 2 input signal
  6. L input signal
(b) All switches are OFF simultaneously for P, R, N, D, 2 and L positions. (2-trip detection logic)
(c) L or 3 input signal is ON for P, R or N position. (2-trip detection logic)
  1. Open or short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. Shift lock control unit assembly (Shift lock control ECU)
  4. ECM

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in the P or N position.
The park/neutral position switch sends a signal to the ECM according to the shift position (P, R, N, D, 2 or L). The ECM determines that there is a problem with the switch or related parts if it receives 2 or more position signals simultaneously or it receives no position signal. The ECM turns on the MIL and stores the DTC.

WIRING DIAGRAM

C117646E02

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the Data List displayed by the intelligent tester, you can read the values of the switches, sensors, actuators and so on without parts removal. Reading the Data List as the first step of troubleshooting is one method of shortening labor time.

  1. Turn the ignition switch off.

  2. Connect the intelligent tester to the DLC3.

  3. Turn the ignition switch on (IG).

  4. Turn on the tester.

  5. Select the following items: Powertrain / Engine and ECT / Data List.

  6. In accordance with the display on the tester, read the Data List.

Item
Measurement Item/
Range (display)
Normal Condition
Diagnostic Note
Shift SW Status (R Range)
PNP (Park/Neutral Position) SW Status/
ON or OFF
Shift lever position;
R: ON
Except R: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
Shift SW Status (P Range)
PNP SW Status/
ON or OFF
Shift lever position;
P: ON
Except P: OFF
Shift SW Status (N Range)
PNP SW Status/
ON or OFF
Shift lever position;
N: ON
Except N: OFF
Shift SW Status (D Range)
PNP SW Status/
ON or OFF
Shift lever position;
D or 3: ON
Except D and 3: OFF
Shift SW Status (3 Range)
PNP SW Status/
ON or OFF
Shift lever position;
3: ON
Except 3: OFF
-
Shift SW Status (2 Range)
PNP SW Status/
ON or OFF
Shift lever position;
2: ON
Except 2: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
Shift SW Status (L Range)
PNP SW Status/
ON or OFF
Shift lever position;
L: ON
Except L: OFF

1. READ VALUE OF DATA LIST (PARK/NEUTRAL POSITION SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn on the intelligent tester.

  1. Select the following items: Powertrain / Engine and ECT / Data List.

  1. In accordance with the display on the tester, read the Data List.

    Item
    Measurement Item/
    Range (display)
    Normal Condition
    Diagnostic Note
    Shift SW Status (R Range)
    PNP (Park/Neutral Position) SW Status/
    ON or OFF
    Shift lever position;
    R: ON
    Except R: OFF
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
    Shift SW Status (P Range)
    PNP SW Status/
    ON or OFF
    Shift lever position;
    P: ON
    Except P: OFF
    Shift SW Status (N Range)
    PNP SW Status/
    ON or OFF
    Shift lever position;
    N: ON
    Except N: OFF
    Shift SW Status (D Range)
    PNP SW Status/
    ON or OFF
    Shift lever position;
    D or 3: ON
    Except D and 3: OFF
    Shift SW Status (2 Range)
    PNP SW Status/
    ON or OFF
    Shift lever position;
    2: ON
    Except 2: OFF
    Shift SW Status (L Range)
    PNP SW Status/
    ON or OFF
    Shift lever position;
    L: ON
    Except L: OFF



OK
Go to step 5
NG


2. CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
C117645E01
  1. Disconnect the park/neutral position switch connector.

  1. Turn the ignition switch on (IG), and measure the voltage.

    Standard voltage:
    Tester Connection
    Specified Condition
    2 (RB) - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
C130119E04
  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance when the shift lever is moved to each position.

    Standard resistance:
    Shift Position
    Tester Connection
    Specified Condition
    P or N
    4 (B) - 5 (L)
    Below 1 Ω
    Except P and N
    4 (B) - 5 (L)
    10 kΩ or higher
    P
    2 (RB) - 6 (PL)
    Below 1 Ω
    Except P
    2 (RB) - 6 (PL)
    10 kΩ or higher
    R
    1 (RL) - 2 (RB)
    Below 1 Ω
    Except R
    1 (RL) - 2 (RB)
    10 kΩ or higher
    N
    2 (RB) - 9 (NL)
    Below 1 Ω
    Except N
    2 (RB) - 9 (NL)
    10 kΩ or higher
    D or 3
    2 (RB) - 7 (DL)
    Below 1 Ω
    Except D and 3
    2 (RB) - 7 (DL)
    10 kΩ or higher
    2
    2 (RB) - 3 (2L)
    Below 1 Ω
    Except 2
    2 (RB) - 3 (2L)
    10 kΩ or higher
    L
    2 (RB) - 8 (LL)
    Below 1 Ω
    Except L
    2 (RB) - 8 (LL)
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
OK


4. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
C130155E01
  1. Connect the park/neutral position switch connector.

  1. Disconnect the ECM connector.

  1. Turn the ignition switch on (IG), and measure the voltage when the shift lever is moved to each position.

    Standard voltage:
    Shift Position
    Tester Connection
    Specified Condition
    P
    73 (P) - Body ground
    10 to 14 V
    Except P
    73 (P) - Body ground
    Below 1 V
    R
    53 (R) - Body ground
    10 to 14 V*
    Except R
    53 (R) - Body ground
    Below 1 V
    N
    54 (N) - Body ground
    10 to 14 V
    Except N
    54 (N) - Body ground
    Below 1 V
    D or 3
    56 (D) - Body ground
    10 to 14 V
    Except D and 3
    56 (D) - Body ground
    Below 1 V
    2
    55 (2) - Body ground
    10 to 14 V
    Except 2
    55 (2) - Body ground
    Below 1 V
    L
    74 (L) - Body ground
    10 to 14 V
    Except L
    74 (L) - Body ground
    Below 1 V

    HINT:
    *: The voltage will drop slightly due to the back up light being turned on.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

5. READ VALUE OF DATA LIST (PARK/NEUTRAL POSITION SWITCH)
  1. Connect the ECM connector.

  1. Turn the ignition switch on (IG).

  1. Turn on the intelligent tester.

  1. Select the following items: Powertrain / Engine and ECT / Data List.

  1. In accordance with the display on the tester, read the Data List.

    Item
    Measurement Item/
    Range (display)
    Normal Condition
    Shift SW Status (3 Range)
    PNP SW Status/
    ON or OFF
    Shift lever position;
    3: ON
    Except 3: OFF



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


6. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - SHIFT LOCK CONTROL ECU)
C117647E01
  1. Disconnect the shift lock control ECU connector.

  1. Turn the ignition switch on (IG), and measure the voltage when the shift lever is moved to each position.

    Standard voltage:
    Shift Position
    Tester Connection
    Specified Condition
    D or 3
    9 (NSSD) - 8 (E)
    10 to 14 V
    Except D and 3
    9 (NSSD) - 8 (E)
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT SHIFT LOCK CONTROL ECU SUB-ASSEMBLY
C117648E02
  1. Disconnect the shift lock control ECU connector.

  1. Measure the resistance when the shift lever is moved to each position.

    Standard resistance:
    Shift Position
    Tester Connection
    Specified Condition
    3
    3 (AT3) - 9 (NSSD)
    Below 1 Ω
    D
    3 (AT3) - 9 (NSSD)
    10 kΩ or higher



NG
REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY
OK


8. CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL ECU - ECM)
A115671E41
  1. Connect the shift lock control ECU connector.

  1. Disconnect the ECM connectors.

  1. Turn the ignition switch on (IG), and measure the voltage.

    Standard voltage:
    Shift Position
    Tester Connection
    Specified Condition
    3
    26 (ODMS) - Body ground
    10 to 14 V
    Except 3
    26 (ODMS) - Body ground
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← DIAGNOSTIC TROUBLE CODE CHART (from Aug 2005)P0710 Transmission Fluid Temperature Sensor "A" Circuit (+ P0712, P0713) (from Aug 2005) →