P0710 Transmission Fluid Temperature Sensor "A" Circuit
Diagnostic trouble codes · Vehicles built from Aug 2005
Also covers:
- P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input
- P0713 Transmission Fluid Temperature Sensor "A" Circuit High Input
DESCRIPTION


The ATF (Automatic Transmission Fluid) temperature sensor converts the fluid temperature into a resistance value which is input to the ECM.
The sensor resistance changes with the transmission fluid temperature. As the temperature rises, the sensor resistance decreases. The ECM applies a voltage to the temperature sensor through ECM terminal THO1, and the ECM calculates the fluid temperature based on the voltage signal.
- HINT:
- The ATF temperature is likely to increase under conditions such as towing, climbing hills and in heavy traffic.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0710 |
Both (a) and (b) are detected momentarily within 0.5 seconds when neither P0712 nor P0713 is detected. (1-trip detection logic) (a) ATF temperature sensor resistance is less than 79 Ω. (b) ATF temperature sensor resistance is more than 156 kΩ.
|
|
| P0712 |
ATF temperature sensor resistance is less than 79 Ω for 0.5 seconds or more. (1-trip detection logic) |
|
| P0713 |
Following condition continues for 0.5 seconds or more. (1-trip detection logic) ATF temperature sensor resistance is more than 156 kΩ after 15 minutes or more after starting engine. |
|
MONITOR DESCRIPTION
The ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects opens or shorts in the ATF temperature circuit. If the resistance value of the ATF temperature is less than 79 Ω*1 or more than 156 kΩ*2, the ECM interprets this as a fault in the ATF sensor or wiring. The ECM turns on the MIL and stores the DTC.*1: 150°C (302°F) or more is indicated regardless of the actual ATF temperature.
*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.
- HINT:
- The ATF temperature can be checked on the intelligent tester display.
WIRING DIAGRAM


INSPECTION PROCEDURE
| DATA LIST |
- HINT:
- Using the Data List displayed by the intelligent tester, you can read the values of the switches, sensors, actuators and so on without parts removal. Reading the Data List as the first step of troubleshooting is one method of shortening labor time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn on the tester.
Select the following items: Powertrain / Engine and ECT / Data List.
In accordance with the display on the tester, read the Data List.
Item
Measurement Item/
Range (display)
Normal Condition
Diagnostic Note
A/T Oil Temperature 1
ATF Temperature Sensor Value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
- After Stall Test; Approximately 80°C (176°F)
- Equal to ambient temperature when cold soak
If value is -40°C (-40°F) or 150°C (302°F) or more, ATF temperature sensor circuit is open or short.
- HINT:
- When DTC P0712 is output and the intelligent tester reading is 150°C (302°F) or more, there is a short circuit.
- When DTC P0713 is output and the intelligent tester reading is -40°C (-40°F), there is an open circuit.
- Measure the resistance between terminal THO1 and the body ground.
Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
150°C (302°F) or more
Short circuit
- HINT:
- If a circuit related to the ATF (Automatic Transmission Fluid) temperature sensor becomes open, P0713 is immediately set (within 0.5 seconds).
- When P0713 is set, P0711 cannot be detected.
- After Stall Test; Approximately 80°C (176°F)
| 1. INSPECT TRANSMISSION WIRE (ATF TEMPERATURE SENSOR) |
![]() ![]() |
Disconnect the transmission wire connector from the transaxle.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
1 (THO) - 6 (E2)
79 Ω to 156 kΩ
1 (THO) - Body ground
10 kΩ or higher
6 (E2) - Body ground
10 kΩ or higher
- HINT:
- If the resistance is outside the specified range at either of the ATF temperature shown in the table below, the driveability of the vehicle may be affected.
- Standard resistance:
ATF Temperature
Specified Condition
20°C (68°F)
3 to 4 kΩ
110°C (230°F)
0.22 to 0.28 kΩ
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM) |
![]() ![]() |
Connect the transmission wire connector to the transaxle.
Disconnect the ECM connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
72 (THO1) - 95 (ETHO)
79 Ω to 156 kΩ
72 (THO1) - Body ground
10 kΩ or higher
95 (ETHO) - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||


