2005-2008 Yaris · Service Manual COMMUNICATION SYSTEM

Yaw Rate Sensor Communication Stop Mode

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

Detection Item
Symptom
Trouble Area
Yaw Rate Sensor Communication Stop Mode
  1. "Yaw Rate / Deceleration Sensor" not displayed on "Communication Bus Check" screen of intelligent tester
  2. Applies to "Yaw Rate Sensor Communication Stop Mode" in "DTC combination table"
  1. Power source circuit of yaw rate sensor
  2. Yaw rate sensor branch wire or connector
  3. Yaw rate sensor

HINT:
  1. For vehicle with VSC only.
  2. When "Communication Bus Check" is performed using the intelligent tester, yaw rate sensors manufactured by TMMF are not displayed on the tester screen.


WIRING DIAGRAM

C120497E17
C131074E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

    HINT:
    Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. CHECK VEHICLE TYPE

Result:
Vehicle Type
Proceed to
TMC Made
A
TMMF Made
B



B
Go to step 4
A


2. CHECK CAN BUS LINE FOR DISCONNECTION (YAW RATE SENSOR BRANCH WIRE)

  1. C125957E01
    Turn the ignition switch off.

  1. Disconnect the D63 yaw rate sensor connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D63-3 (CANH) - D63-2 (CANL)
    Ignition Switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CAN-H, CAN-L)
OK


3. CHECK HARNESS AND CONNECTOR (IG, GND)

  1. C125957E02
    Disconnect the D63 yaw rate sensor connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D63-1 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D63-5 (IG) - Body ground
    Ignition Switch on (IG)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE YAW RATE SENSOR

4. CHECK CAN BUS WIRE

  1. C131807E01
    Turn the ignition switch off.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Proceed to
    D83-2 (YAW1) - D83-1 (YAW2)
    Ignition switch off
    54 to 69 Ω
    A
    D83-2 (YAW1) - D83-1 (YAW2)
    Ignition switch off
    70 Ω more
    B
    D83-2 (YAW1) - D83-1 (YAW2)
    Ignition switch off
    54 Ω less
    C



B
Go to step 13

C
Go to step 15
A


5. CHECK CAN BUS LINE FOR SHORT TO +B

  1. C131807E02
    Turn the ignition switch off.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D83-2 (YAW1) - D83-3 (VYS)
    Ignition switch off
    50 kΩ or higher
    D83-1 (YAW2) - D83-3 (VYS)
    Ignition switch off
    50 kΩ or higher



NG
Go to step 9
OK


6. CHECK CAN BUS LINE FOR SHORT TO GND

  1. C131807E03
    Turn the ignition switch off.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D83-2 (YAW1) - D83-5 (GYAW)
    Ignition switch off
    500 Ω or higher
    D83-1 (YAW2) - D83-5 (GYAW)
    Ignition switch off
    500 Ω or higher



NG
Go to step 11
OK


7. CHECK HARNESS AND CONNECTOR (VYS, GYAW)

  1. C130892E03
    Disconnect the D83 yaw rate sensor connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D83-5 (GYAW) - Body ground
    Ignition switch off
    Below 1 Ω

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D83-3 (VYS) - Body ground
    Ignition switch on (IG)
    6 to 16 V



NG
REPLACE YAW RATE SENSOR
OK


8. CHECK HARNESS AND CONNECTOR (ABS AND TRACTION ACTUATOR - YAW RATE SENSOR)

  1. C133425E01
    Disconnect the A39 ABS and traction actuator (skid control ECU) connector.

  1. Measure the resistance.

    HINT:
    The resistance must be measured after the D83 yaw rate sensor connector is disconnected.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D83-3 (VYS) - A39-17 (VYS)
    Ignition switch off
    Below 1 Ω
    D83-5 (GYAW) - A39-23 (GYAW)
    Ignition switch off
    Below 1 Ω



OK
REPLACE ABS AND TRACTION ACTUATOR (SKID CONTROL ECU)
NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)

9. CHECK CAN BUS LINE FOR SHORT TO +B (YAW RATE SENSOR)

  1. C130892E04
    Turn the ignition switch off.

  1. Disconnect the D83 yaw rate sensor connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D83-2 (YAW1) - D83-3 (VYS)
    Ignition switch off
    1 MΩ or higher
    D83-1 (YAW2) - D83-3 (VYS)
    Ignition switch off
    1 MΩ or higher



OK
REPLACE YAW RATE SENSOR
NG


10. CHECK CAN BUS LINE FOR SHORT TO +B (ABS AND TRACTION ACTUATOR - YAW RATE SENSOR)

  1. C130880E08
    Turn the ignition switch off.

  1. Disconnect the A39 ABS and traction actuator (skid control ECU) connector.

  1. C130892E04
    Measure the resistance.

    HINT:
    The resistance must be measured after the D83 yaw rate sensor connector is disconnected.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D83-2 (YAW1) - D83-3 (VYS)
    Ignition switch off
    100 kΩ or higher
    D83-1 (YAW2) - D83-3 (VYS)
    Ignition switch off
    100 kΩ or higher



OK
REPLACE ABS AND TRACTION ACTUATOR (SKID CONTROL ECU)
NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (ABS AND TRACTION ACTUATOR - YAW RATE SENSOR (CAN-H, CAN-L))

11. CHECK CAN BUS LINE FOR SHORT TO GND (YAW RATE SENSOR)

  1. C130892E05
    Turn the ignition switch off.

  1. Disconnect the D83 yaw rate sensor connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D83-2 (YAW1) - D83-5 (GYAW)
    Ignition switch off
    1 kΩ or higher
    D83-1 (YAW2) - D83-5 (GYAW)
    Ignition switch off
    1 kΩ or higher



OK
REPLACE YAW RATE SENSOR
NG


12. CHECK CAN BUS LINE FOR SHORT TO GND (ABS AND TRACTION ACTUATOR - YAW RATE SENSOR)

  1. C130880E08
    Turn the ignition switch off.

  1. Disconnect the A39 ABS and traction actuator (skid control ECU) connector.

  1. C130892E05
    Measure the resistance.

    HINT:
    The resistance must be measured after the D83 yaw rate sensor connector is disconnected.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D83-2 (YAW1) - D83-5 (GYAW)
    Ignition switch off
    1 kΩ or higher
    D83-1 (YAW2) - D83-5 (GYAW)
    Ignition switch off
    1 kΩ or higher



OK
REPLACE ABS AND TRACTION ACTUATOR (SKID CONTROL ECU)
NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (ABS AND TRACTION ACTUATOR - YAW RATE SENSOR (CAN-H, CAN-L))

13. CHECK CAN MAIN WIRE OR CONNECTOR (ABS AND TRACTION ACTUATOR (SKID CONTROL ECU))

  1. C130880E09
    Turn the ignition switch off.

  1. Disconnect the ABS and traction actuator (skid control ECU) connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A39-6 (SS1) - A39-12 (SS2)
    Ignition switch off
    108 to 132 Ω



OK
REPLACE ABS AND TRACTION ACTUATOR (SKID CONTROL ECU)
NG


14. CHECK CAN MAIN WIRE OR CONNECTOR (ABS AND TRACTION ACTUATOR - YAW RATE SENSOR)
  1. Turn the ignition switch off.

  1. C133425E02
    Disconnect the D83 yaw rate sensor connector.

  1. Measure the resistance.

    HINT:
    The resistance must be measured after the A39 ABS and traction actuator (skid control ECU) connector is disconnected.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A39-6 (SS1) - D83-2 (YAW1)
    Ignition switch off
    Below 1 Ω
    A39-12 (SS2) - D83-1 (YAW2)
    Ignition switch off
    Below 1 Ω



OK
REPLACE YAW RATE SENSOR
NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (ABS AND TRACTION ACTUATOR - YAW RATE SENSOR (CAN-H, CAN-L))

15. CHECK CAN BUS LINES FOR SHORT CIRCUIT (ABS AND TRACTION ACTUATOR (SKID CONTROL ECU))

  1. C130880E09
    Turn the ignition switch off.

  1. Disconnect the ABS and traction actuator (skid control ECU) connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A39-6 (SS1) - A39-12 (SS2)
    Ignition switch off
    108 to 132 Ω



OK
REPLACE ABS AND TRACTION ACTUATOR (SKID CONTROL ECU)
NG


16. CHECK CAN BUS LINES FOR SHORT CIRCUIT (ABS AND TRACTION ACTUATOR - YAW RATE SENSOR)

  1. C130892E06
    Turn the ignition switch off.

  1. Disconnect the D83 yaw rate sensor connector.

  1. C130880E09
    Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A39-6 (SS1) - A39-12 (SS2)
    Ignition switch off
    1 MΩ or higher



OK
REPLACE YAW RATE SENSOR
NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (ABS AND TRACTION ACTUATOR - YAW RATE SENSOR (CAN-H, CAN-L))


← Steering Angle Sensor Communication Stop Mode (from Aug 2005)ECM Communication Stop Mode (Aug 2005 – Oct 2005) →