2005-2008 Yaris · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2005


1. INSPECT 3RD GEAR THRUST CLEARANCE

G021219
  1. Using a feeler gauge, measure the 3rd gear thrust clearance.

    Standard clearance:
    0.10 to 0.35 mm (0.0039 to 0.0138 in.)

    Maximum clearance:
    0.35 mm (0.0138 in.)

    If the clearance exceeds the maximum, replace the 3rd gear synchronizer ring.


2. INSPECT 5TH GEAR THRUST CLEARANCE

G021220
  1. Using a dial indicator, measure the 5th gear thrust clearance.

    Standard clearance:
    0.10 to 0.50 mm (0.0039 to 0.0197 in.)

    Maximum clearance:
    0.50 mm (0.0197 in.)

    If the clearance exceeds the maximum, replace the 5th gear synchronizer ring.


3. INSPECT 3RD GEAR RADIAL CLEARANCE

G021221
  1. Using a dial indicator, measure the 3rd gear radial clearance.

    Standard clearance:
    0.015 to 0.058 mm (0.0006 to 0.0023 in.)

    Maximum clearance:
    0.058 mm (0.0023 in.)

    If the clearance exceeds the maximum, replace the 3rd gear needle roller bearing or the shaft.


4. INSPECT 4TH GEAR RADIAL CLEARANCE

G021222
  1. Using a dial indicator, measure the 4th gear radial clearance.

    Standard clearance:
    0.015 to 0.058 mm (0.0006 to 0.0023 in.)

    Maximum clearance:
    0.058 mm (0.0023 in.)

    If the clearance exceeds the maximum, replace the 4th gear needle roller bearing or the shaft.


5. INSPECT 5TH GEAR RADIAL CLEARANCE

G021223
  1. Using a dial indicator, measure the 5th gear radial clearance.

    Standard clearance:
    0.015 to 0.058 mm (0.0006 to 0.0023 in.)

    Maximum clearance:
    0.058 mm (0.0023 in.)

    If the clearance exceeds the maximum, replace the 5th gear needle roller bearing or the shaft.


6. REMOVE 5TH GEAR

G021224E02
  1. Using SST and a press, remove the input shaft rear radial ball bearing, hub sleeve No. 3, 5th gear synchronizer ring and 5th gear from the input shaft.

    SST
    09950-00020  
    09612-24014   (09612-10061)

    HINT:
    1. Support the input shaft by hand to prevent it from dropping off.
    2. Set the claw of SST between the 4th gear and 5th gear, as shown in the illustration.

    NOTICE:
    Do not excessively tighten SST.


7. REMOVE TRANSMISSION CLUTCH HUB NO.3

G021225
  1. Remove the 2 shifting key springs No. 1 from transmission clutch hub No. 3.

  1. Remove transmission hub sleeve No. 3 from transmission clutch hub No. 3.

  1. Remove the 3 shifting keys No. 3 from transmission clutch hub No. 3.


8. REMOVE 5TH GEAR NEEDLE ROLLER BEARING

G021226
  1. Remove the 5th gear needle roller bearing from the input shaft.


9. REMOVE 5TH GEAR BEARING SPACER

G021227
  1. Remove the 5th gear bearing spacer from the input shaft.


10. INSPECT 4TH GEAR THRUST CLEARANCE

G021228
  1. Using a dial indicator, measure the 4th gear thrust clearance.

    Standard clearance:
    0.10 to 0.55 mm (0.0039 to 0.0217 in.)

    Maximum clearance:
    0.55 mm (0.0217 in.)

    If the clearance exceeds the maximum, replace the 4th gear synchronizer ring.


11. REMOVE 5TH GEAR SHAFT SNAP RING

G021229
  1. Using a snap ring expander, remove the 5th gear shaft snap ring from the input shaft.

    HINT:
    Do not damage the journal surface of the input shaft.


12. REMOVE 5TH GEAR THRUST WASHER

G021230
  1. Remove the 5th gear thrust washer from the input shaft.


13. REMOVE 5TH GEAR THRUST WASHER BALL

G021231
  1. Using a magnetic finger, remove the ball from the input shaft.


14. REMOVE 4TH GEAR

G021257
  1. Remove the 4th gear from the input shaft.


15. REMOVE 4TH GEAR NEEDLE ROLLER BEARING

G021256
  1. Remove the 4th gear needle roller bearing from the input shaft.


16. REMOVE 4TH GEAR BEARING SPACER

G021255
  1. Remove the 4th gear bearing spacer from the input shaft.


17. REMOVE 4TH GEAR SYNCHRONIZER RING

G021254
  1. Remove the 4th gear synchronizer ring from clutch hub No. 2.


18. REMOVE CLUTCH HUB NO.2 SETTING SHAFT SNAP RING

G021233
  1. Using a snap ring expander, remove the clutch hub No. 2 setting shaft snap ring from the input shaft.

    HINT:
    Do not damage the journal surface of the input shaft.


19. REMOVE 3RD GEAR

G021234E01
  1. Using SST and a press, remove hub sleeve No. 2, the 3rd gear synchronizer ring and 3rd gear from the input shaft.

    SST
    09950-00020  

    NOTICE:
    1. Do not excessively tighten SST.
    2. Support the input shaft by hand to prevent it from dropping off


20. REMOVE TRANSMISSION CLUTCH HUB NO.2

G021235
  1. Remove the 2 shifting key springs No. 1 from transmission clutch hub No. 2.

  1. Remove transmission hub sleeve No. 2 from transmission clutch hub No. 2.

  1. Remove the 3 shifting keys No. 2 from transmission clutch hub No. 2.


21. REMOVE 3RD GEAR NEEDLE ROLLER BEARING

G021236
  1. Remove the 3rd gear needle roller bearing from the input shaft.


22. REMOVE INPUT SHAFT FRONT BEARING

G021237E03
  1. Using a press, remove the input shaft front bearing from the input shaft.

    SST
    09950-00020  

    HINT:
    Support the input shaft by hand to prevent it from dropping off.

← COMPONENTS (from Aug 2005)INSPECTION (from Aug 2005) →