2005-2008 Yaris · Service Manual TRANSMISSION

INSPECTION

Inspection · Vehicles built from Aug 2005


INSPECT INPUT SHAFT

G021244
  1. Check the input shaft for wear and damage.

  1. Using a dial indicator, check the input shaft runout.

    Maximum runout:
    0.03 mm (0.0012 in.)

    If the runout exceeds the maximum, replace the input shaft.

  1. G021245E01
    Using a micrometer, measure the outer diameter of the input shaft journal surface, at the locations indicated.

    Standard:
    Measured Part
    Outer Diameter mm (in.)
    A
    25.502 to 25.515 (1.0040 to 1.00453)
    B
    30.985 to 31.000 (1.2199 to 1.2205)
    C, D
    33.985 to 34.000 (1.3380 to 1.3386)
    E
    23.002 to 23.015 (0.9056 to 0.9091)
    F
    22.967 to 23.000 (0.9042 to 0.9055)

    If the outer diameters are below the minimums, replace the input shaft.


INSPECT 3RD GEAR

G021246
  1. Using a cylinder gauge, measure the inside diameter of the 3rd gear.

    Standard inside diameter:
    39.015 to 39.031 mm (1.5360 to 1.5367 in.)

    Maximum inside diameter:
    39.031 mm (1.5367 in.)

    If the inside diameter exceeds the maximum, replace the 3rd gear.


INSPECT 4TH GEAR

G021246
  1. Using a cylinder gauge, measure the inside diameter of the 4th gear.

    Standard inside diameter:
    39.015 to 39.031 mm (1.5360 to 1.5367 in.)

    Maximum inside diameter:
    39.031 mm (1.5367 in.)

    If the inside diameter exceeds the maximum, replace the 4th gear.


INSPECT 5TH GEAR

G021246
  1. Using a cylinder gauge, measure the inside diameter of the 5th gear.

    Standard inside diameter:
    36.015 to 36.031 mm (1.4179 to 1.4185 in.)

    Maximum inside diameter:
    36.031 mm (1.4185 in.)

    If the inside diameter exceeds the maximum, replace the 5th gear.


INSPECT 3RD GEAR SYNCHRONIZER RING

G021238
  1. Check for wear and damage.

  1. Coat the 3rd gear cone with gear oil.

  1. Turn the 3rd gear synchronizer ring in one direction while pushing it against the 3rd gear cone.

  1. Check that the ring locks.
    If the synchronizer ring does not lock, replace the synchronizer ring.

  1. G021239
    Using a feeler gauge, measure the clearance between the synchronizer ring back and the gear spline end.

    Standard clearance:
    0.75 to 1.65 mm (0.0295 to 0.0650 in.)

    Minimum clearance:
    0.75 mm (0.0295 in.)

    If the clearance is less than the minimum, replace the synchronizer ring.


INSPECT 4TH GEAR SYNCHRONIZER RING

G021238
  1. Check for wear and damage.

  1. Coat the 4th gear cone with gear oil.

  1. Turn the synchronizer ring in one direction while pushing it against the 4th gear cone.

  1. Check that the ring locks.
    If the synchronizer ring does not lock, replace the synchronizer ring.

  1. G021239
    Using a feeler gauge, measure the clearance between the synchronizer ring back and the gear spline end.

    Standard clearance:
    0.75 to 1.65 mm (0.0295 to 0.0650 in.)

    Minimum clearance:
    0.75 mm (0.0295 in.)

    If the clearance is less than the minimum, replace the synchronizer ring.


INSPECT 5TH GEAR SYNCHRONIZER RING

G021238
  1. Check for wear and damage.

  1. Coat the 5th gear cone with gear oil.

  1. Turn the synchronizer ring in one direction while pushing it against the 5th gear cone.

  1. Check that the ring locks.
    If the synchronizer ring does not lock, replace the synchronizer ring.

  1. G021239
    Using a feeler gauge, measure the clearance between the synchronizer ring back and the gear spline end.

    Standard clearance:
    0.75 to 1.65 mm (0.0295 to 0.0650 in.)

    Minimum clearance:
    0.75 mm (0.0295 in.)

    If the clearance is less than the minimum, replace the synchronizer ring.


INSPECT TRANSMISSION HUB SLEEVE NO.2

G021241E01
  1. Using vernier calipers, measure the clearance between transmission hub sleeve No. 2 and shift fork No. 2.

    Standard clearance (A-B):
    0.15 to 0.35 mm (0.0059 to 0.0138 in.)

    If the clearance is outside the specifications, replace transmission hub sleeve No. 2 and gear shift fork No. 2.


INSPECT TRANSMISSION HUB SLEEVE NO.3

G021243E01
  1. Using vernier calipers, measure the clearance between transmission hub sleeve No. 3 and shift fork No. 3.

    Standard clearance (A-B):
    0.15 to 0.35 mm (0.0059 to 0.0138 in.)

    If the clearance is outside the specifications, replace transmission hub sleeve No. 3 and gear shift fork No. 3.

← DISASSEMBLY (from Aug 2005)REASSEMBLY (from Aug 2005) →