2005-2008 Yaris · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Aug 2005


1. INSTALL INPUT SHAFT FRONT BEARING

G021247E01
  1. Using SST and a press, install a new input shaft front bearing onto the input shaft.

    SST
    09515-10010  


2. INSTALL 3RD GEAR NEEDLE ROLLER BEARING

G021236
  1. Coat the 3rd gear needle roller bearing with gear oil, and install it onto the input shaft.


3. INSTALL 3RD GEAR

G021248
  1. Coat the 3rd gear with gear oil, and install it onto the input shaft.


4. INSTALL 3RD GEAR SYNCHRONIZER RING

G021249
  1. Coat the 3rd gear synchronizer ring with gear oil, and install it onto the 3rd gear.


5. INSTALL TRANSMISSION CLUTCH HUB NO.2

G021235
  1. Install the 3 shifting keys No. 2, 2 shifting key springs and transmission hub sleeve No. 2 onto clutch hub No. 2.

    NOTICE:
    Assemble transmission hub sleeve No. 2 and transmission clutch hub No. 2 in the correct orientations, as shown in the illustration.

  1. G021250E01
    Using SST and a press, install transmission clutch hub sleeve No. 2 onto the input shaft.
    SST
    09506-35010  


6. INSTALL CLUTCH HUB NO.2 SETTING SHAFT SNAP RING

G021251E01
  1. Select a snap ring that allows the minimum axial play.

    Standard clearance:
    0.1 mm (0.0039 in.) or less.

    Mark
    Thickness
    mm (in.)
    Mark
    Thickness
    mm (in.)
    A
    2.28 (0.0898)
    D
    2.46 (0.0969)
    B
    2.34 (0.0921)
    E
    2.52 (0.0992)
    C
    2.40 (0.0945)
    F
    2.58 (0.1016)

  1. G021233
    Using a snap ring expander, install the new snap ring onto the input shaft.

    HINT:
    Do not damage the journal surface of the input shaft.


7. INSPECT 3RD GEAR THRUST CLEARANCE

G021252
  1. Using a feeler gauge, measure the 3rd gear thrust clearance.

    Standard clearance:
    0.10 to 0.35 mm (0.0039 to 0.0138 in.)

    Maximum clearance:
    0.35 mm (0.0138 in.)

    If the clearance exceeds the maximum, replace the 3rd gear synchronizer ring.


8. INSPECT 3RD GEAR RADIAL CLEARANCE

G021253
  1. Using a dial indicator, measure the 3rd gear radial clearance.

    Standard clearance:
    0.015 to 0.058 mm (0.0006 to 0.0023 in.)

    Maximum clearance:
    0.058 mm (0.0023 in.)

    If the clearance exceeds the maximum, replace the 3rd gear needle roller bearing or the shaft.


9. INSTALL 4TH GEAR SYNCHRONIZER RING

G021254
  1. Coat the 4th gear synchronizer ring with gear oil, and install it onto transmission clutch hub No. 2.


10. INSTALL 4TH GEAR BEARING SPACER

G021255
  1. Coat the 4th gear bearing spacer with gear oil, and install it onto the input shaft.


11. INSTALL 4TH GEAR NEEDLE ROLLER BEARING

G021256
  1. Coat the 4th gear needle roller bearing with gear oil, and install it onto the input shaft.


12. INSTALL 4TH GEAR

G021257
  1. Coat the 4th gear with gear oil, and install it onto the input shaft.


13. INSTALL 5TH GEAR THRUST WASHER BALL

G021346
  1. Install the 5th gear thrust washer ball onto the input shaft.


14. INSTALL 5TH GEAR THRUST WASHER

G021230
  1. Coat the 5th gear thrust washer with gear oil, and install it onto the input shaft.


15. INSTALL 5TH GEAR SHAFT SNAP RING

G021347E01
  1. Select a snap ring, using the table below, that makes the thrust clearance of the 5th gear thrust washer less than 0.1 mm (0.0039 in.).

    Mark
    Thickness
    mm (in.)
    Mark
    Thickness
    mm (in.)
    1
    2.28 (0.0898)
    4
    2.46 (0.0969)
    2
    2.34 (0.0921)
    5
    2.52 (0.0992)
    3
    2.40 (0.0945)
    6
    2.58 (0.1016)

  1. G021229
    Using a snap ring expander, install the new snap ring onto the input shaft.

    HINT:
    Do not damage the journal surface of the input shaft.


16. INSPECT 4TH GEAR THRUST CLEARANCE

G021349
  1. Using a dial indicator, measure the 4th gear thrust clearance.

    Standard clearance:
    0.1 to 0.55 mm (0.0039 to 0.0217 in.)

    Maximum clearance:
    0.55 mm (0.0217 in.)

    If the clearance exceeds the maximum, replace the 4th gear synchronizer ring.


17. INSPECT 4TH GEAR RADIAL CLEARANCE

G021350
  1. Using a dial indicator, measure the 4th gear radial clearance.

    Standard clearance:
    0.015 to 0.058 mm (0.0006 to 0.0023 in.)

    Maximum clearance:
    0.058 mm (0.0023 in.)

    If the clearance exceeds the maximum, replace the 4th gear needle roller bearing or the shaft.


18. INSTALL 5TH GEAR BEARING SPACER

G021227
  1. Coat the 5th gear bearing spacer with gear oil, and install it onto the input shaft.


19. INSTALL 5TH GEAR NEEDLE ROLLER BEARING

G021226
  1. Coat the 5th gear needle roller bearing with gear oil, and install it onto the input shaft.


20. INSTALL 5TH GEAR

G021351
  1. Coat the 5th gear with gear oil, and install it onto the input shaft.


21. INSTALL 5TH GEAR SYNCHRONIZER RING

G021352
  1. Coat the 5th gear synchronizer ring with gear oil, and install it onto the 5th gear.


22. INSTALL TRANSMISSION CLUTCH HUB NO.3

G021353
  1. Install the 3 shifting keys No. 3, 2 shifting key springs No. 1 and transmission hub sleeve No. 3 onto transmission clutch hub No. 3.

    NOTICE:
    Assemble transmission hub sleeve No. 3 and transmission clutch hub No. 3 in the correct orientations, as shown in the illustration.

  1. Place the 5th gear synchronizer ring on the 5th gear, and align the synchronizer ring slots with shifting keys No. 3.

  1. G021354E01
    Using SST and a press, press the No. 3 hub sleeve into the input shaft.
    SST
    09515-10010  

    NOTICE:
    Install transmission hub sleeve No. 3 in the correct orientation, as shown in the illustration.


23. INSTALL INPUT SHAFT REAR RADIAL BALL BEARING

G021355E01
  1. Using SST and a press, install a new input shaft rear radial ball bearing onto the input shaft.

    SST
    09515-10010  


24. INSPECT 5TH GEAR THRUST CLEARANCE

G021220
  1. Using a dial indicator, measure the 5th gear thrust clearance.

    Standard clearance:
    0.10 to 0.50 mm (0.0039 to 0.0197 in.)

    Maximum clearance:
    0.50 mm (0.0197 in.)

    If the clearance exceeds the maximum, replace the 5th gear synchronizer ring.


25. INSPECT 5TH GEAR RADIAL CLEARANCE

G021223
  1. Using a dial indicator, measure the 5th gear radial clearance.

    Standard clearance:
    0.015 to 0.058 mm (0.0006 to 0.0023 in.)

    Maximum clearance:
    0.058 mm (0.0023 in.)

    If the clearance exceeds the maximum, replace the 5th gear needle roller bearing or the shaft.

← INSPECTION (from Aug 2005)COMPONENTS (from Aug 2005) →