2005-2008 Yaris · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. REMOVE OUTPUT SHAFT REAR BEARING

G021356E01
  1. Using SST and a press, remove the output shaft rear bearing.

    SST
    09950-60010   (09951-00220)
    09950-70010   (09951-07100)


2. INSPECT 1ST GEAR THRUST CLEARANCE

G021392
  1. Using a feeler gauge, measure the 1st gear thrust clearance.

    Standard clearance:
    0.10 to 0.45 mm (0.0039 to 0.0177 in.)

    Maximum clearance:
    0.45 mm (0.0177 in.)

    If the clearance exceeds the maximum, replace the 1st gear synchronizer ring.


3. INSPECT 2ND GEAR THRUST CLEARANCE

G021393
  1. Using a feeler gauge, measure the 2nd gear thrust clearance.

    Standard clearance:
    0.10 to 0.55 mm (0.0039 to 0.0217 in.)

    Maximum clearance:
    0.55 mm (0.0217 in.)

    If the clearance exceeds the maximum, replace the 2nd gear synchronizer ring.


4. INSPECT 1ST GEAR RADIAL CLEARANCE

G021394
  1. Using a dial indicator, measure the 1st gear radial clearance.

    Standard clearance:
    0.015 to 0.056 mm (0.0006 to 0.0022 in.)

    Maximum clearance:
    0.056 mm (0.0022 in.)

    If the clearance exceeds the maximum, replace the 1st gear needle roller bearing or the shaft.


5. INSPECT 2ND GEAR RADIAL CLEARANCE

G021395
  1. Using a dial indicator, measure the 2nd gear radial clearance.

    Standard clearance:
    0.015 to 0.056 mm (0.0006 to 0.0022 in.)

    Maximum clearance:
    0.056 mm (0.0022 in.)

    If the clearance exceeds the maximum, replace the 2nd gear needle roller bearing or the shaft.


6. REMOVE COUNTER 5TH GEAR SHAFT SNAP RING

G021399
  1. Using 2 screwdrivers and a hammer, remove the counter 5th gear shaft snap ring from the output shaft.


7. REMOVE 4TH DRIVEN GEAR

G021391
  1. Using a press, remove the 5th driven gear and 4th driven gear from the output shaft.


8. REMOVE OUTPUT SHAFT SPACER

G021357
  1. Remove the output shaft spacer from the output shaft.


9. REMOVE 2ND GEAR

G021358E01
  1. Using SST and a press, remove the 3rd driven gear and 2nd gear from the output shaft.

    SST
    09950-00020  


10. REMOVE 2ND GEAR NEEDLE ROLLER BEARING

G021384
  1. Remove the 2nd gear needle roller bearing from the output shaft.


11. REMOVE 2ND GEAR BEARING SPACER

G021383
  1. Remove the 2nd gear bearing spacer from the output shaft.


12. REMOVE 2ND GEAR SYNCHRONIZER RING

C118339
  1. Remove the 2nd gear synchronizer ring from the reverse gear.


13. REMOVE CLUTCH HUB NO.1 SHAFT SNAP RING

C118338
  1. Using 2 screwdrivers, remove the clutch hub No. 1 shaft snap ring from the output shaft.

    HINT:
    Do not damage the journal surface of the output shaft.


14. REMOVE 1ST GEAR

G021360
  1. Using a press, remove the transmission clutch hub No. 1 and 1st gear from the output shaft.


15. REMOVE 1ST GEAR NEEDLE ROLLER BEARING

G021361
  1. Remove the 1st gear needle roller bearing from the output shaft.


16. REMOVE OUTPUT SHAFT FRONT BEARING

G021362E01
  1. Using SST and a press, remove the output shaft front bearing from the output shaft.

    SST
    09950-00020  


17. REMOVE TRANSMISSION CLUTCH HUB NO.1

G021363
  1. Remove the 2 shifting key springs No. 1, 3 shifting keys No. 1 and reverse gear from the transmission clutch hub No. 1.

← COMPONENTS (from Nov 2005)INSPECTION (from Nov 2005) →