2005-2008 Yaris · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. INSTALL OUTPUT SHAFT FRONT BEARING

G021374E01
  1. Using SST and a press, install the output shaft front bearing onto the output shaft.

    SST
    09710-22021   (09710-01051)


2. INSTALL 1ST GEAR NEEDLE ROLLER BEARING

G021375
  1. Coat the 1st gear needle roller bearing with gear oil, and install it onto the output shaft.


3. INSTALL 1ST GEAR

G021376
  1. Coat the 1st gear with gear oil, and install it onto the output shaft.


4. INSTALL 1ST GEAR SYNCHRONIZER RING

C118337
  1. Coat the 1st gear synchronizer ring with gear oil, and install it onto the 1st gear.


5. INSTALL TRANSMISSION CLUTCH HUB NO.1

G021378
  1. Install 2 shifting key springs No. 1, 3 shifting keys No. 1 and the reverse gear onto the transmission clutch hub No. 1.

  1. G021379E01
    Using SST and a press, install the transmission clutch hub No. 1 onto the output shaft.
    SST
    09316-60011   (09316-00011, 09316-00071)

    NOTICE:
    Install the reverse gear assembly in the correct orientation, as shown in the illustration.


6. INSTALL CLUTCH HUB NO.1 SHAFT SNAP RING

G021380
  1. Select a snap ring that allows the minimum axial play.

    Standard clearance:
    0 to 0.1 mm (0 to 0.0039 in.)

    Mark
    Thickness mm (in.)
    Mark
    Thickness mm (in.)
    A
    2.28 (0.0898)
    D
    2.46 (0.0969)
    B
    2.34 (0.0921)
    E
    2.52 (0.0992)
    C
    2.40 (0.0945)
    F
    2.58 (0.1016)

  1. C118340
    Using a snap ring expander, install the new snap ring onto the output shaft.


7. INSPECT 1ST GEAR THRUST CLEARANCE

G021381
  1. Using a feeler gauge, measure the 1st gear thrust clearance.

    Standard clearance:
    0.10 to 0.45 mm (0.0039 to 0.0177 in.)
    Maximum clearance:
    0.45 mm (0.0177 in.)

    If the clearance exceeds the maximum, replace the 1st gear synchronizer ring.


8. INSPECT 1ST GEAR RADIAL CLEARANCE

G021382
  1. Using a dial indicator, measure the 1st gear radial clearance.

    Standard clearance:
    0.015 to 0.056 mm (0.0006 to 0.0022 in.)

    Maximum clearance:
    0.056 mm (0.0022 in.)

    If the clearance exceeds the maximum, replace the 1st gear needle roller bearing or the shaft.


9. INSTALL 2ND GEAR BEARING SPACER

G021383
  1. Coat the 2nd gear bearing spacer with gear oil and install it onto the output shaft.


10. INSTALL 2ND GEAR NEEDLE ROLLER BEARING

G021384
  1. Coat the 2nd gear needle roller bearing with gear oil, and install it onto the output shaft.


11. INSTALL 2ND GEAR SYNCHRONIZER RING

C118339
  1. Coat the 2nd synchronizer ring with gear oil, and install it onto the reverse gear.


12. INSTALL 2ND GEAR

G021386
  1. Coat the 2nd gear with gear oil, and install it onto the output shaft.


13. INSTALL 3RD DRIVEN GEAR

G021387E01
  1. Using SST and a press, install the 3rd driven gear onto the output shaft.

    SST
    09316-60011   (09316-00041)


14. INSPECT 2ND GEAR THRUST CLEARANCE

G021388
  1. Using a feeler gauge, measure the 2nd gear thrust clearance.

    Standard clearance:
    0.10 to 0.55 mm (0.0039 to 0.0217 in.)
    Maximum clearance :
    0.55 mm (0.0217 in.)

    If the clearance exceeds the maximum, replace the 2nd gear synchronizer ring.


15. INSPECT 2ND GEAR RADIAL CLEARANCE

G021389
  1. Using a dial indicator, measure the 2nd gear radial clearance between the gear and shaft.

    Standard clearance:
    0.015 to 0.056 mm (0.0006 to 0.0023 in.)

    Maximum clearance:
    0.056 mm (0.0023 in.)

    If the clearance exceeds the maximum, replace the 2nd gear needle roller bearing or the shaft.


16. INSTALL OUTPUT SHAFT SPACER

G021357
  1. Install the output shaft spacer onto the output shaft.


17. INSTALL 4TH DRIVEN GEAR

G021390E01
  1. Using SST and a press, install the 4th driven gear onto the output shaft.

    SST
    09223-00010  
    09316-60011   (09316-00021)


18. INSTALL 5TH DRIVEN GEAR

G021396E01
  1. Using SST and a press, install the 5th driven gear onto the output shaft.

    SST
    09223-00010  
    09316-60011   (09316-00021)


19. INSTALL COUNTER 5TH GEAR SHAFT SNAP RING

G021397E01
  1. Select a snap ring, using the table below, that makes the thrust clearance of the 5th driven gear less than 0.1 mm (0.0039 in.).

    Mark
    Thickness mm (in.)
    Mark
    Thickness mm (in.)
    A
    2.22 (0.0874)
    F
    2.52 (0.0992)
    B
    2.28 (0.0898)
    G
    2.58 (0.1016)
    C
    2.34 (0.0921)
    H
    2.64 (0.1039)
    D
    2.40 (0.0945)
    J
    2.70 (0.1063)
    E
    2.46 (0.0969)
    -
    -

  1. G021401
    Using a brass bar and hammer, tap the new snap ring onto the output shaft.


20. INSTALL OUTPUT SHAFT REAR BEARING

C121092E01
  1. Using SST and a press, install the output shaft rear bearing onto the output shaft.

    SST
    09612-22011  

← INSPECTION (from Nov 2005)COMPONENTS (from Nov 2005) →