B1805/52 Short in Front Passenger Side Squib Circuit
Diagnostic trouble codes · Vehicles built from Aug 2005
Also covers:
- B1806/52 Open in Front Passenger Side Squib Circuit
- B1807/52 Short to GND in Front Passenger Side Squib Circuit
- B1808/52 Short to B+ in Front Passenger Side Squib Circuit
DESCRIPTION
The front passenger side squib circuit consists of the center airbag sensor assembly and the front passenger airbag assembly.The circuit signals the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side squib circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1805/52 |
|
|
| B1806/52 |
|
|
| B1807/52 |
|
|
| B1808/52 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Perform the simulation method by selecting CHECK MODE (signal check) with the intelligent tester (Click here).
- After selecting CHECK MODE (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).
- Perform the simulation method by selecting CHECK MODE (signal check) with the intelligent tester (Click here).
| 1. CHECK FRONT PASSENGER AIRBAG (FRONT PASSENGER SIDE SQUIB) |
- SST
- 09843-18060
Turn the ignition switch off.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connectors from the front passenger airbag assembly.
Connect the white wire side of SST (resistance 2.1 Ω) to connector E (orange connector).
- CAUTION:
- Never connect a tester to the front passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.
- NOTICE:
- Do not forcibly insert the SST into the terminals of the connector when connecting.
- Insert the SST straight into the terminals of the connector.
- Do not forcibly insert the SST into the terminals of the connector when connecting.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1805, B1806, B1807, B1808 and 52 are not output.
- HINT:
- DTCs other than DTC B1805, B1806, B1807, B1808 and 52 may be output at this time, but they are not related to this check.
|
|
||||
| NG | |
| 2. CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST from connector E.
Check that the instrument panel wire assembly connectors (on the front passenger airbag side) are not damaged.
- OK:
- The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
|
|
||||
| OK | |
| 3. CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT |
Disconnect the connectors from the center airbag sensor assembly and front passenger airbag assembly.

Check for short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage.
- Standard voltage:
Tester connection
Condition
Specified condition
Q1-2 (P+) - Body ground
Ignition switch on (IG)
Below 1 V
Q1-1 (P-) - Body ground
Ignition switch on (IG)
Below 1 V
Check for open in the circuit.
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified condition
Q1-2 (P+) - Q1-1 (P-)
Always
Below 1 Ω
Check for short to ground in the circuit.
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified condition
Q1-2 (P+) - Body ground
Always
1 MΩ or higher
Q1-1 (P-) - Body ground
Always
1 MΩ or higher
Check for short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified condition
Q1-2 (P+) - Q1-1 (P-)
Always
1 MΩ or higher
|
|
||||
| OK | |
| 4. CHECK CENTER AIRBAG SENSOR ASSEMBLY |
Connect the connectors to the front passenger airbag and the center airbag sensor assembly.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1805, B1806, B1807, B1808 and 52 are not output.
- HINT:
- DTCs other than DTC B1805, B1806, B1807, B1808 and 52 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
| 5. CHECK INSTRUMENT PANEL WIRE |
Restore the released activation prevention mechanism of connector B to the original condition.

Disconnect the instrument panel wire connector from the instrument panel wire assembly.
Check for short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage.
- Standard voltage:
Tester connection
Condition
Specified condition
DQ2-1 (P+) -
Body ground
Ignition switch on (IG)
Below 1 V
DQ2-2 (P-) -
Body ground
Ignition switch on (IG)
Below 1 V
Check for open in the circuit.
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified condition
DQ2-1 (P+) - DQ2-2 (P-)
Always
Below 1 Ω
Check for short to ground in the circuit.
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified condition
DQ2-1 (P+) -
Body ground
Always
1 MΩ or higher
DQ2-2 (P-) -
Body ground
Always
1 MΩ or higher
Check for short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified condition
DQ2-1 (P+) - DQ2-2 (P-)
Always
1 MΩ or higher
|
|
||||
| OK | |
| 6. CHECK INSTRUMENT PANEL WIRE ASSEMBLY |
Check for short to B+ in the circuit.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage.
- Standard voltage:
Tester connection
Condition
Specified condition
Q1-2 (P+) - Body ground
Ignition switch on (IG)
Below 1 V
Q1-1 (P-) - Body ground
Ignition switch on (IG)
Below 1 V
Check for open in the circuit.
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified condition
Q1-2 (P+) - Q1-1 (P-)
Always
Below 1 Ω
Check for short to ground in the circuit.
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified condition
Q1-2 (P+) - Body ground
Always
1 MΩ or higher
Q1-1 (P-) - Body ground
Always
1 MΩ or higher
Check for short in the circuit.
Release the activation prevention mechanism built into connector D (Click here).
Measure the resistance.
- Standard resistance:
Tester connection
Condition
Specified condition
Q1-2 (P+) - Q1-1 (P-)
Always
1 MΩ or higher
|
|
||||
| OK | ||
| ||
