2005-2008 Yaris · Service Manual ENGINE

DATA LIST / ACTIVE TEST

System information · Vehicles built from Nov 2006


DATA LIST

HINT:
Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List in troubleshooting is one way to save time.

NOTICE:
In the table below, the values listed under normal conditions are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.

  1. Turn the engine switch off.

  2. Connect the intelligent tester to the DLC3.

  3. Turn the engine switch on (IG) and turn the tester ON.

  4. Select the following menu items: Body / Body ECU / Data List.

  5. Check the values by referring to the table below.

    Main body ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG SW
    Engine switch / ON or OFF
    ON: Engine switch is on (IG)
    OFF: Engine switch is off
    -
    ACC SW
    Engine switch / ON or OFF
    ON: Engine switch is on (ACC)
    OFF: Engine switch is off
    -
    St SW1
    Start switch 1 / ON or OFF
    ON: Engine switch is on (IG)
    OFF: Engine switch is off
    -
    St SW2
    Start switch 2 / ON or OFF
    ON: Engine switch is on (IG)
    OFF: Engine switch is off
    -
    Str Unlock SW
    Steering lock condition / ON or OFF
    ON: Steering is unlocked
    OFF: Steering is locked
    -
    N SW / C SW
    Clutch switch / ON or OFF
    ON: Clutch pedal is depressed
    OFF: Clutch pedal is released
    -
    Stop Lamp SW1
    Stop light switch/ ON or OFF
    ON: Brake pedal is depressed
    OFF: Brake ped
    -
    Vehicle Spd Sig
    Vehicle speed signal / STOP or RUN
    STOP: Vehicle is stopped
    RUN: Vehicle is running
    -
    E/G Cond
    Engine condition / STOP or RUN
    STOP: Engine is stopped
    RUN: Engine is running
    -
    IG1 Relay Mon1
    IG1 outer relay monitor / ON or OFF
    ON: Engine switch is on (IG)
    OFF: Engine switch is off
    -
    IG2 Relay Mon1
    IG2 outer relay monitor / ON or OFF
    ON: Engine switch is on (IG)
    OFF: Engine switch is off
    -
    IG1 Relay Mon2
    IG1 inner relay monitor / ON or OFF
    ON: Engine switch is on (IG)
    OFF: Engine switch is off
    -
    IG2 Relay Mon2
    IG2 inner relay monitor / ON or OFF
    ON: Engine switch is on (IG)
    OFF: Engine switch is off
    -
    ACC Relay Mon
    ACC relay monitor / ON or OFF
    ON: Eengine switch is on (ACC)
    OFF: Engine switch is off
    -
    Ratch Circuit
    Ratch circuit / ON or OFF
    ON: Engine switch is on (IG)
    OFF: Engine switch is off, on (ACC) or engine is running
    -
    Start Req Sig
    Starter request signal / ON or OFF
    ON: ST relay is ON
    OFF: ST relay is OFF
    -
    Pwr Cond
    Power supply condition / ALL, ACC ON, IG1 IG2, ST ON
    ALL: All relays are ON
    ACC ON: ACC relay is ON
    IG1: IG1 relay is ON
    IG2: IG2 relay is ON
    ST ON: ST relay is ON
    -
    #Code
    Number of diagnosis codes / Min: 0, max: 255
    -
    -
    Certification ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG SW
    Engine switch / ON or OFF
    ON: Engine switch is on (IG)
    OFF: Engine switch is off
    -
    ACC SW
    Engine switch / ON or OFF
    ON: Engine switch is on (ACC)
    OFF: Eengine switch is off
    -
    Key Lo-batt Wrn
    Electrical key battery conditions / ON or OFF
    ON: Battery has been depleted
    OFF: Battery has been depleted
    -
    Unmatch Format
    Code format/ YES or NO
    YES: Code format matches
    NO: Code format differs
    -
    No response
    Response/ YES or NO
    YES: Response
    NO: No response
    -
    Wrong Code
    ID code/ YES or NO
    YES: ID code matches
    NO: ID code differs
    -
    Wrong C Code
    Challenge code/ YES or NO
    YES: Challenge code matches
    NO: Challenge code differs
    -
    Unmatch V-ID
    Key number/ YES or NO
    YES: Key number matches
    NO: Key number differs
    -
    Permit (Start)
    Engine start permission by certification ECU/ PERMIT or PROHIBIT
    PERMIT: Engine start is permitted
    PROHIBIT: Engine start is prohibited
    -
    Start Rqst
    Starter request signal / ON or OFF
    YES: Engine switch off
    NO: ST relay is OFF
    -
    S Code Chk
    S code certification result/ NG or OK
    NG: S code certification result is abnormal
    OK: S code certification result is normal
    -
    L Code Chk
    L code certification result/ NG or OK
    NG: L code certification result is abnormal
    OK: L code certification result is normal
    -


ACTIVE TEST

HINT:
Performing an Active Test enables components including the relays, VSV (Vacuum Switching Valve), and actuators, to be operated without removing any parts. The Active Test can be performed with an intelligent tester. Performing an Active Test as the first step of troubleshooting is one method of shortening diagnostic time. Data List can be displayed during Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch to on (IG).

  3. Turn the tester ON.

  4. Select the following menu items: Body / Body ECU / Active Test.

  5. Perform the Active Test by referring to the table below.

Main body ECU 
Tester Display
Test Part
Control Range
Lighting Ind
Indicator illumination
ON/OFF
Ind Condition
Indicator light illumination pattern
Green/Amber/No Sig
S Lock Pwr
Steering lock ECU power supply
ON/OFF
Certification ECU 
Tester Display
Test Part
Control Range
Fr Transmitter
Indoor electrical key antenna (front)
ON / OFF
← DTC CHECK / CLEAR (from Nov 2006)DIAGNOSTIC TROUBLE CODE CHART (from Nov 2006) →