2005-2008 Yaris · Service Manual BODY ELECTRICAL

Room Oscillator does not Recognize Key

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

If the entry ignition function does not operate, place the key in the vehicle and check whether the engine control system starts. If the engine control system starts (the ID code box outputs a start permission signal to the engine control system and the engine control system starts), it can be assumed that only the entry ignition system is malfunctioning.
The certification ECU uses the indoor electrical key oscillator to send a request signal to the key when: 1) the driver's door is opened and closed, or 2) the ignition switch is turned from on (ACC) to off or off to on. Then, the key transmits its ID code to the door control receiver. The ID code, which is then sent to the certification ECU, is verified by the certification ECU and the verification result is sent to the ID code box. Turning the ignition switch from on (ACC) to off stops the engine control system.
The ID code box and the certification ECU communicate encryption codes to each other using the LIN communication line. When the return code from the certification ECU matches the ID code in the memory, the ID code box sends an engine control system start permission signal to the ECM. With the clutch pedal depressed, pressing the ignition switch starts the engine. With the engine running, pressing the ignition switch stops the engine.

WIRING DIAGRAM

B127164E01

INSPECTION PROCEDURE


1. CHECK OPERATION OF ELECTRICAL KEY
  1. After replacing the electrical key with a normally functioning one, check that the wireless lock and unlock functions operate normally.

    OK:
    Wireless lock and unlock functions operate normally.



OK
END (ELECTRICAL KEY IS DEFECTIVE)
NG


2. PERFORM ACTIVE TEST BY INTELLIGENT TESTER (INDOOR ELECTRICAL KEY OSCILLATOR)
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the antenna operates.

    Certification ECU: 
    Item
    Test Details
    Diagnostic Note
    Fr Transmitter
    Indoor electrical key oscillator (front) ON / OFF
    -
    In Bdr Transmitter
    indoor electrical key oscillator (rear) ON / OFF
    -

    OK:
    When key is brought close to indoor electrical key oscillator, oscillator is turned OFF and indicator on key illuminates.



OK
REPLACE CERTIFICATION ECU ASSEMBLY
NG


3. CHECK HARNESS AND CONNECTOR (INDOOR ELECTRICAL KEY OSCILLATOR - CERTIFICATION ECU)

  1. B108063E09
    Disconnect the D61 and J36 antenna connectors.

  1. Disconnect the D60 ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D61-1 (CLG3) - D60-11 (CLG5)*1
    Below 1 Ω
    D61-1 (CLG3) or D60-11 (CLG5)*1 - Body ground
    10 kΩ or higher
    J36-1 (CLG6) - D60-15 (CLG7)*2
    Below 1 Ω
    J36-1 (CLG6) - D60-15 (CLG7)*2 - Body ground
    10 kΩ or higher
    D61-3 (CLGB) - D60-12 (CG5B)*1
    Below 1 Ω
    D61-3 (CLGB) or D60-12 (CG5B)*1 - Body ground
    10 kΩ or higher
    J36-3 (CLGB) - D60-16 (CG7B)*2
    Below 1 Ω
    J36-3 (CLGB) - D60-16 (CG7B)*2 - Body ground
    10 kΩ or higher

  1. Reconnect the antenna connectors.

  1. Reconnect the ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK INDOOR ELECTRICAL KEY OSCILLATOR
  1. Carry the key into the vehicle.

  1. Replace the indoor electrical key oscillator with a new one.

  1. Depress the clutch pedal and check that the ignition switch indicator illuminates in green.

    OK:
    Ignition switch indicator illuminates in green.



OK
END (INDOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)
NG

REPLACE CERTIFICATION ECU ASSEMBLY


← Front Passenger Side Door Entry Lock Function does not Operate (from Aug 2005)Entry Interior Alarm does not Sound (from Aug 2005) →