2005-2008 Yaris · Service Manual COMMUNICATION SYSTEM

TERMINALS OF ECU

System information · Vehicles built from Aug 2005

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

    HINT:
    Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


JUNCTION CONNECTOR (LHD)

  1. C118162E03
    D-CAN J/C

    Wiring color:
    D-CAN J/C connectors
    Terminal
    Color
    Brake actuator (skid control ECU)*1 (CAN-H)
    ABS and traction actuator (skid control ECU)*2 (CAN-H)
    D41-1 (ABS)
    G
    Brake actuator (skid control ECU)*1 (CAN-L)
    ABS and traction actuator (skid control ECU)*2 (CAN-L)
    D41-12 (ABS)
    W
    Steering sensor*2 (CAN-H)
    D41-2 (STR)
    SB
    Steering sensor*2 (CAN-L)
    D41-13 (STR)
    W
    DLC 3 (CAN-H)
    D41-3 (OBD)
    V
    DLC 3 (CAN-L)
    D41-14 (OBD)
    W
    ECM (CAN-H)
    D41-4 (EFI)
    L
    ECM (CAN-L)
    D41-15 (EFI)
    W
    Air conditioning amplifier*3 (CAN-H)
    D41-6 (A/C)
    V
    Air conditioning amplifier*3 (CAN-L)
    D41-17 (A/C)
    W
    Center airbag sensor assembly (CAN-H)
    D41-8 (A/B)
    B
    Center airbag sensor assembly (CAN-L)
    D41-19 (A/B)
    W
    CAN Main wire (between D-CAN J/C and P-CAN J/C (CAN-H))
    D41-11 (TORH)
    Y
    CAN Main wire (between D-CAN J/C and P-CAN J/C (CAN-L))
    D41-22 (TORH)
    W

    HINT:
    *1: w/ ABS
    *2: w/ VSC
    *3: w/ Air conditioning or PTC heater

  2. C118162E04
    P-CAN J/C

    Wiring color:
    P-CAN J/C connectors
    Terminal
    Color
    Yaw rate sensor*1 (CAN-H)
    D42-2 (YAW)
    O
    Yaw rate sensor*1 (CAN-L)
    D42-13 (YAW)
    W
    Power steering ECU (CAN-H)
    D42-4 (EPS)
    SB
    Power steering ECU (CAN-L)
    D42-15 (EPS)
    W
    Main body ECU (CAN-H)
    D42-5 (JB)
    R
    Main body ECU (CAN-L)
    D42-16 (JB)
    W
    Certification ECU*2 (CAN-H)
    D42-6 (SMRT)
    GR
    Certification ECU*2 (CAN-L)
    D42-17 (SMRT)
    W
    Combination meter ECU (CAN-H)
    D42-7 (MET)
    G
    Combination meter ECU (CAN-L)
    D42-18 (MET)
    W
    CAN Main wire (between P-CAN J/C and D-CAN J/C (CAN-H))
    D42-11 (TOLH)
    Y
    CAN Main wire (between P-CAN J/C and D-CAN J/C (CAN-L))
    D42-22 (TOLH)
    W

    HINT:
    *1: w/ VSC (TMC Made)
    *2: w/ Entry and start system

  3. Wiring diagram for identifying CAN J/C connectors
    C120656E03
    C130760E01
    C130761E01


JUNCTION CONNECTOR (RHD)

  1. C118162E08
    D-CAN J/C

    Wiring color:
    D-CAN J/C connectors
    Terminal
    Color
    Steering sensor*1 (CAN-H)
    D42-1 (STR)
    SB
    Steering sensor*1 (CAN-L)
    D42-12 (STR)
    W
    Yaw rate sensor*2 (CAN-H)
    D42-2 (YAW)
    O
    Yaw rate sensor*2 (CAN-L)
    D42-13 (YAW)
    W
    DLC 3 (CAN-H)
    D42-3 (OBD)
    V
    DLC 3 (CAN-L)
    D42-14 (OBD)
    W
    Power steering ECU (CAN-H)
    D42-4 (EPS)
    SB
    Power steering ECU (CAN-L)
    D42-15 (EPS)
    W
    Main body ECU (CAN-H)
    D42-5 (JB)
    R
    Main body ECU (CAN-L)
    D42-16 (JB)
    W
    Certification ECU*3 (CAN-H)
    D42-6 (SMRT)
    GR
    Certification ECU*3 (CAN-L)
    D42-17 (SMRT)
    W
    Combination meter ECU (CAN-H)
    D42-7 (MET)
    G
    Combination meter ECU (CAN-L)
    D42-18 (MET)
    W
    CAN Main wire (between D-CAN J/C and P-CAN J/C (CAN-H))
    D42-11 (TOLH)
    Y
    CAN Main wire (between D-CAN J/C and P-CAN J/C (CAN-L))
    D42-22 (TOLH)
    W

    HINT:
    *1: w/ VSC
    *2: w/ VSC (TMC Made)
    *3: w/ Entry and start system

  2. C118162E09
    P-CAN J/C

    Wiring color:
    P-CAN J/C connectors
    Terminal
    Color
    Brake actuator (skid control ECU)*1 (CAN-H)
    ABS and traction actuator (skid control ECU)*2 (CAN-H)
    D41-1 (ABS)
    G
    Brake actuator (skid control ECU)*1 (CAN-L)
    ABS and traction actuator (skid control ECU)*2 (CAN-L)
    D41-12 (ABS)
    W
    ECM (CAN-H)
    D41-4 (EFI)
    L
    ECM (CAN-L)
    D41-15 (EFI)
    W
    Air conditioning amplifier*3 (CAN-H)
    D41-6 (A/C)
    V
    Air conditioning amplifier*3 (CAN-L)
    D41-17 (A/C)
    W
    Center airbag sensor assembly ECU (CAN-H)
    D41-8 (A/B)
    B
    Center airbag sensor assembly ECU (CAN-L)
    D41-19 (A/B)
    W
    CAN Main wire (between P-CAN J/C and D-CAN J/C (CAN-H))
    D41-11 (TOLH)
    Y
    CAN Main wire (between P-CAN J/C and D-CAN J/C (CAN-L))
    D41-22 (TOLH)
    W

    HINT:
    *1: w/ ABS
    *2: w/ VSC
    *3: w/ Air conditioning or PTC heater

  3. Wiring diagram for identifying CAN J/C connectors
    C120657E02
    C130762E01
    C130763E01


DLC3
G026206E68
  1. Turn the ignition switch off.

  2. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D15-6 (CANH) - D15-14 (CANL)
    V - W
    Ignition switch off
    54 to 69 Ω
    D15-6 (CANH) - D15-4 (CG)
    V - W-B
    Ignition switch off
    200 Ω or higher
    D15-14 (CANL) - D15-4 (CG)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D15-6 (CANH) - D15-16 (BAT)
    V - SB
    Ignition switch off
    6 kΩ or higher
    D15-14 (CANL) - D15-16 (BAT)
    W - SB
    Ignition switch off
    6 kΩ or higher


BRAKE ACTUATOR (SKID CONTROL ECU) (TMC Made)
C118165E21

HINT:
For vehicle with ABS only.

  1. Turn the ignition switch off.

  2. Disconnect the A15 brake actuator (skid control ECU) connector.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    A15-6 (CANH) - A15-5 (CANL)
    G - W
    Ignition switch off
    54 to 69 Ω
    A15-6 (CANH) - A15-2 (GND1)
    G - W-B
    Ignition switch off
    200 Ω or higher
    A15-5 (CANL) - A15-2 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A15-6 (CANH) - A15-1 (+BS)
    G - W
    Ignition switch off
    6 kΩ or higher
    A15-5 (CANL) - A15-1 (+BS)
    W - W
    Ignition switch off
    6 kΩ or higher


BRAKE ACTUATOR (SKID CONTROL ECU) (TMMF Made)
C130880E01

HINT:
For vehicle with ABS only.

  1. Turn the ignition switch off.

  2. Disconnect the brake actuator (skid control ECU) connector.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    A39-10 (CANH) - A39-8 (CANL)
    G - W
    Ignition switch off
    54 to 69 Ω
    A39-10 (CANH) - A39-13 (GND1)
    G - W-B
    Ignition switch off
    200 Ω or higher
    A39-8 (CANL) - A39-13 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A39-10 (CANH) - A39-14 (+BS)
    G - W
    Ignition switch off
    6 kΩ or higher
    A39-8 (CANL) - A39-14 (+BS)
    W - W
    Ignition switch off
    6 kΩ or higher


ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) (TMC Made)
C118187E03

HINT:
For vehicle with VSC only.

  1. Turn the ignition switch off.

  2. Disconnect the A31 ABS and traction actuator (skid control ECU) connector.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    A31-11 (CANH) - A31-25 (CANL)
    G - W
    Ignition switch off
    54 to 69 Ω
    A31-11 (CANH) - A31-32 (GND1)
    G - W-B
    Ignition switch off
    200 Ω or higher
    A31-25 (CANL) - A31-32 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A31-11 (CANH) - A31-31 (+BS)
    G - W
    Ignition switch off
    6 kΩ or higher
    A31-25 (CANL) - A31-31 (+BS)
    W - W
    Ignition switch off
    6 kΩ or higher


ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) (TMMF Made)
C130880E02

HINT:
For vehicle with VSC only.

  1. Turn the ignition switch off.

  2. Disconnect the A39 ABS and traction actuator (skid control ECU) connector.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    A39-10 (CANH) - A39-8 (CANL)
    G - W
    Ignition switch off
    54 to 69 Ω
    A39-10 (CANH) - A39-13 (GND1)
    G - W-B
    Ignition switch off
    200 Ω or higher
    A39-8 (CANL) - A39-13 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A39-10 (CANH) - A39-14 (+BS)
    G - W
    Ignition switch off
    6 kΩ or higher
    A39-8 (CANL) - A39-14 (+BS)
    W - W
    Ignition switch off
    6 kΩ or higher
    A39-6 (SS1) - A39-12 (SS2)
    P - BR
    Ignition switch off
    108 to 132 Ω
    A39-6 (SS1) - A39-13 (GND1)
    P - W-B
    Ignition switch off
    1 kΩ or higher
    A39-12 (SS2) - A39-13 (GND1)
    BR - W-B
    Ignition switch off
    1 kΩ or higher
    A39-6 (SS1) - A39-14 (+BS)
    P - W
    Ignition switch off
    1 MΩ or higher
    A39-12 (SS2) - A39-14 (+BS)
    BR - W
    Ignition switch off
    1 MΩ or higher


STEERING SENSOR
G030155E34

HINT:
For vehicle with VSC only.

  1. Turn the ignition switch off.

  2. Disconnect the D62 steering sensor connector.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D62-10 (CANH) - D62-9 (CANL)
    SB - W
    Ignition switch off
    54 to 69 Ω
    D62-10 (CANH) - D62-2 (ESS)
    SB - W-B
    Ignition switch off
    200 Ω or higher
    D62-9 (CANL) - D62-2 (ESS)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D62-10 (CANH) - D62-3 (BAT)
    SB - LG
    Ignition switch off
    6 kΩ or higher
    D62-9 (CANL) - D62-3 (BAT)
    W - LG
    Ignition switch off
    6 kΩ or higher


YAW RATE SENSOR (TMC Made)
C125958E01

HINT:
For vehicle with VSC only.

  1. Turn the ignition switch off.

  2. Disconnect the D63 yaw rate sensor connector.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D63-3 (CANH) - D63-2 (CANL)
    O - W
    Ignition switch off
    54 to 69 Ω
    D63-3 (CANH) - D63-1 (GND)
    O - W-B
    Ignition switch off
    200 Ω or higher
    D63-2 (CANL) - D63-1 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D63-3 (CANH) - D15-16 (BAT)
    O - SB
    Ignition switch off
    6 kΩ or higher
    D63-2 (CANL) - D15-16 (BAT)
    W - SB
    Ignition switch off
    6 kΩ or higher


YAW RATE SENSOR (TMMF Made)
C130892E01

HINT:
For vehicle with VSC only.

  1. Turn the ignition switch off.

  2. Disconnect the D83 yaw rate sensor connector.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D83-2 (YAW1) - D83-1 (YAW2)
    P - BR
    Ignition switch off
    108 to 132 Ω
    D83-2 (YAW1) - D83-5 (GYAW)
    P - L
    Ignition switch off
    1 kΩ or higher
    D83-1 (YAW2) - D83-5 (GYAW)
    BR - L
    Ignition switch off
    1 kΩ or higher
    D83-2 (YAW1) - D83-3 (VYS)
    P - O
    Ignition switch off
    1 MΩ or higher
    D83-1 (YAW2) - D83-3 (VYS)
    BR - O
    Ignition switch off
    1 MΩ or higher


AIR CONDITIONING AMPLIFIER (w/ Auto Air Conditioning)
G100279E04

HINT:
For vehicle with auto air conditioning or PTC heater only.

  1. Turn the ignition switch off.

  2. Disconnect the E11 air conditioning amplifier connector.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    E11-11 (TX+) - E11-12 (TX-)
    V - W
    Ignition switch off
    54 to 69 Ω
    E11-11 (TX+) - E11-14 (GND)
    V - W-B
    Ignition switch off
    200 Ω or higher
    E11-12 (TX-) - E11-14 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    E11-11 (TX+) - E11-21 (B)
    V - P
    Ignition switch off
    6 kΩ or higher
    E11-12 (TX-) - E11-21 (B)
    W - P
    Ignition switch off
    6 kΩ or higher


AIR CONDITIONING AMPLIFIER (w/ Manual Air Conditioning)
C118854E04

HINT:
For vehicle with manual air conditioning or PTC heater only.

  1. Turn the ignition switch off.

  2. Disconnect the E8 air conditioning amplifier connector.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    E8-2 (TX+) - E8-3 (TX-)
    V - W
    Ignition switch off
    54 to 69 Ω
    E8-2 (TX+) - E8-12 (GND)
    V - W-B
    Ignition switch off
    200 Ω or higher
    E8-3 (TX-) - E8-12 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    E8-2 (TX+) - D15-16 (BAT)
    V - SB
    Ignition switch off
    6 kΩ or higher
    E8-3 (TX-) - D15-16 (BAT)
    W - SB
    Ignition switch off
    6 kΩ or higher


ECM (1KR-FE Engine) (TMC Made)
C118186E01
  1. Turn the ignition switch off.

  2. Disconnect the A32 ECM connector.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    A32-25 (CANH) - A32-33 (CANL)
    L - W
    Ignition switch off
    108 to 132 Ω
    A32-25 (CANH) - A32-1 (E1)
    L - W-B
    Ignition switch off
    200 Ω or higher
    A32-33 (CANL) - A32-1 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A32-25 (CANH) - A32-22 (BATT)
    L - V
    Ignition switch off
    6 kΩ or higher
    A32-33 (CANL) - A32-22 (BATT)
    W - V
    Ignition switch off
    6 kΩ or higher


ECM (1KR-FE Engine) (TMMF Made)
C118186E02
  1. Turn the ignition switch off.

  2. Disconnect the A32 ECM connector.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    A32-25 (CANH) - A32-33 (CANL)
    L - W
    Ignition switch off
    108 to 132 Ω
    A32-25 (CANH) - A32-1 (E1)
    L - W-B
    Ignition switch off
    200 Ω or higher
    A32-33 (CANL) - A32-1 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A32-25 (CANH) - A32-22 (BATT)
    L - V
    Ignition switch off
    6 kΩ or higher
    A32-33 (CANL) - A32-22 (BATT)
    W - V
    Ignition switch off
    6 kΩ or higher
    A32-34 (CAN+)* - A32-26 (CAN-)*
    W - B
    Ignition switch off
    108 to 132 Ω
    A32-34 (CAN+)* - A32-1 (E1)
    W - W-B
    Ignition switch off
    1 kΩ or higher
    A32-26 (CAN-)* - A32-1 (E1)
    B - W-B
    Ignition switch off
    1 kΩ or higher
    A32-34 (CAN+)* - A32-22 (BATT)
    W - V
    Ignition switch off
    1 MΩ or higher
    A32-26 (CAN-)* - A32-22 (BATT)
    B - V
    Ignition switch off
    1 MΩ or higher

    HINT:
    *: w/ Multi-mode manual transaxle


ECM (1NZ / 2NZ-FE Engine)
C125959E01
  1. Turn the ignition switch off.

  2. Disconnect the A21 and C20 ECM connectors.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    A21-41 (CANH) - A21-49 (CANL)
    L - W
    Ignition switch off
    108 to 132 Ω
    A21-41 (CANH) - C20-104 (E1)
    L - W
    Ignition switch off
    200 Ω or higher
    A21-49 (CANL) - C20-104 (E1)
    W - W
    Ignition switch off
    200 Ω or higher
    A21-41 (CANH) - A21-20 (BATT)
    L - Y
    Ignition switch off
    6 kΩ or higher
    A21-49 (CANL) - A21-20 (BATT)
    W - Y
    Ignition switch off
    6 kΩ or higher


ECM (2SZ-FE Engine)
C125959E04
  1. Turn the ignition switch off.

  2. Disconnect the A21 and C20 ECM connectors.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    A21-41 (CANH) - A21-49 (CANL)
    L - W
    Ignition switch off
    108 to 132 Ω
    A21-41 (CANH) - C20-104 (E1)
    L - W
    Ignition switch off
    200 Ω or higher
    A21-49 (CANL) - C20-104 (E1)
    W - W
    Ignition switch off
    200 Ω or higher
    A21-41 (CANH) - A21-20 (BATT)
    L - Y
    Ignition switch off
    6 kΩ or higher
    A21-49 (CANL) - A21-20 (BATT)
    W - Y
    Ignition switch off
    6 kΩ or higher
    A21-5 (CAN+)* - A21-4 (CAN-)*
    W -B
    Ignition switch off
    108 to 132 Ω
    A21-5 (CAN+)* - C20-104 (E1)
    W - W
    Ignition switch off
    1 kΩ or higher
    A21-4 (CAN-)* - C20-104 (E1)
    B - W
    Ignition switch off
    1 kΩ or higher
    A21-5 (CAN+)* - A21-20 (BATT)
    W - Y
    Ignition switch off
    1 MΩ or higher
    A21-4 (CAN-)* - A21-20 (BATT)
    B - Y
    Ignition switch off
    1 MΩ or higher

    HINT:
    *: w/ Multi-mode manual transaxle


ECM (1ND-TV Engine)
C131850E03
  1. Turn the ignition switch off.

  2. Disconnect the A49 ECM connector.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    A49-24 (CANH) - A49-46 (CANL)
    L - W
    Ignition switch off
    108 to 132 Ω
    A49-24 (CANH) - A49-2 (E1)
    L - W-B
    Ignition switch off
    200 Ω or higher
    A49-46 (CANL) - A49-2 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A49-24 (CANH) - D15-16 (BAT)
    L - SB
    Ignition switch off
    6 kΩ or higher
    A49-46 (CANL) - D15-16 (BAT)
    W - SB
    Ignition switch off
    6 kΩ or higher
    A49-45 (CAN+)* - A49-64 (CAN-)*
    W -B
    Ignition switch off
    108 to 132 Ω
    A49-45 (CAN+)* - A49-2 (E1)
    W - W-B
    Ignition switch off
    1 kΩ or higher
    A49-64 (CAN-)* - A49-2 (E1)
    B - W-B
    Ignition switch off
    1 kΩ or higher
    A49-45 (CAN+)* - D15-16 (BAT)
    W - SB
    Ignition switch off
    1 MΩ or higher
    A49-64 (CAN-)* - D15-16 (BAT)
    B - SB
    Ignition switch off
    1 MΩ or higher

    HINT:
    *: w/ Multi-mode manual transaxle


TRANSMISSION CONTROL ECU
C130932E01

HINT:
For vehicle with multi-mode transaxle only.

  1. Turn the ignition switch off.

  2. Disconnect the A38 and D79 transmission control ECU connectors.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    A38-1 (CAN+) - A38-2 (CAN-)
    W - B
    Ignition switch off
    108 to 132 Ω
    A38-1 (CANH) - D79-6 (GND)
    W - W-B
    Ignition switch off
    1 kΩ or higher
    A38-2 (CAN-) - D79-6 (GND)
    B - W-B
    Ignition switch off
    1 kΩ or higher
    A38-1 (CAN+) - D79-1 (+B)
    W - B
    Ignition switch off
    1 MΩ or higher
    A38-2 (CAN-) - D79-1 (+B)
    B - B
    Ignition switch off
    1 MΩ or higher


CENTER AIRBAG SENSOR ASSEMBLY
C131070E01
  1. Turn the ignition switch off.

  2. Disconnect the D16 center airbag sensor assembly connector.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D16-13 (CANH) - D16-22 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    D16-13 (CANH) - D16-25 (E1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    D16-22 (CANL) - D16-25 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D16-13 (CANH) - D15-16 (BAT)
    B - SB
    Ignition switch off
    6 kΩ or higher
    D16-22 (CANL) - D15-16 (BAT)
    W - SB
    Ignition switch off
    6 kΩ or higher


POWER STEERING ECU
C118163E02
  1. Turn the ignition switch off.

  2. Disconnect the A19 and D31 power steering ECU connectors.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D31-1 (CANH) - D31-7 (CANL)
    SB - W
    Ignition switch off
    108 to 132 Ω
    D31-1 (CANH) - A19-2 (PGND)
    SB - W-B
    Ignition switch off
    200 Ω or higher
    D31-7 (CANL) - A19-2 (PGND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D31-1 (CANH) - A19-1 (PIG)
    SB - W
    Ignition switch off
    6 kΩ or higher
    D31-7 (CANL) - A19-1 (PIG)
    W - W
    Ignition switch off
    6 kΩ or higher


COMBINATION METER ECU
C139156E01
  1. Turn the ignition switch off.

  2. Disconnect the D1 combination meter assembly connector.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D1-20 (CANH) - D1-21 (CANL)
    G - W
    Ignition switch off
    54 to 69 Ω
    D1-20 (CANH) - D1-24 (ET)
    G - BR
    Ignition switch off
    200 Ω or higher
    D1-21 (CANL) - D1-24 (ET)
    W - BR
    Ignition switch off
    200 Ω or higher
    D1-20 (CANH) - D1-2 (ECUB)
    G - L
    Ignition switch off
    6 kΩ or higher
    D1-21 (CANL) - D1-2 (ECUB)
    W - L
    Ignition switch off
    6 kΩ or higher


CERTIFICATION ECU
G100280E07

HINT:
For vehicle with entry and start system only.

  1. Turn the ignition switch off.

  2. Disconnect the D60 certification ECU connector.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D60-27 (CANH) - D60-28 (CANL)
    GR - W
    Ignition switch off
    54 to 69 Ω
    D60-27 (CANH) - D60-17 (E)
    GR - W-B
    Ignition switch off
    200 Ω or higher
    D60-28 (CANL) - D60-17 (E)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D60-27 (CANH) - D60-1 (+B1)
    GR - B
    Ignition switch off
    6 kΩ or higher
    D60-28 (CANL) - D60-1 (+B1)
    W - B
    Ignition switch off
    6 kΩ or higher


MAIN BODY ECU (w/ Entry and Start System)
E114510E12
B108612E16
  1. Turn the ignition switch off.

  2. Disconnect the D66, 4B and 4E connectors.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D66-15 (CANH) - D66-16 (CANL)
    R - W
    Ignition switch off
    54 to 69 Ω
    D66-15 (CANH) - 4E-17 (GND1)
    R - W-B
    Ignition switch off
    200 Ω or higher
    D66-16 (CANL) - 4E-17 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D66-16 (CANH) - 4B-30 (BECU)
    R - L
    Ignition switch off
    6 kΩ or higher
    D66-15 (CANL) - 4B-30 (BECU)
    L - L
    Ignition switch off
    6 kΩ or higher


MAIN BODY ECU (w/o Entry and Start System)
E114510E12
B108641E15
  1. Turn the ignition switch off.

  2. Disconnect the D33, 4B and 4E connectors.

  3. Measure the resistance.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D33-23 (CANH) - D33-22 (CANL)
    R - W
    Ignition switch off
    54 to 69 Ω
    D33-23 (CANH) - 4E-17 (GND1)
    R - W-B
    Ignition switch off
    200 Ω or higher
    D33-22 (CANL) - 4E-17 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D33-23 (CANH) - 4B-30 (BECU)
    R - L
    Ignition switch off
    6 kΩ or higher
    D33-22 (CANL) - 4B-30 (BECU)
    W - L
    Ignition switch off
    6 kΩ or higher

← PROBLEM SYMPTOMS TABLE (from Nov 2005)DIAGNOSIS SYSTEM (from Aug 2005) →