2005-2008 Yaris · Service Manual COMMUNICATION SYSTEM

DIAGNOSIS SYSTEM

Troubleshooting · Vehicles built from Aug 2005


BUS CHECK (COMMUNICATION MALFUNCTION DTC)

HINT:
Only CAN communication system DTCs for each ECU can be displayed on the intelligent tester.

  1. G029877E01
    Select "Bus Check" from the "System Select" screen on the intelligent tester.

  2. G029878
    Select "Communication Malfunction DTC" from the "Bus Check" screen, and then select "Enter".

  3. G029879
    Select the system of the DTC to be checked and select "Details".

  4. G029880
    CAN communication system DTCs are displayed.


BUS CHECK (COMMUNICATION BUS CHECK)

HINT:
The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the intelligent tester.

  1. G029878
    Select "Communication Bus Check" from the "Bus Check" screen.

  2. G029881
    The screen displays the ECUs and sensors that are properly connected to the CAN communication system.

    HINT:
    1. If any properly connected ECUs or sensors are not displayed, there is a communication stop in the system (Click here).
    2. Display the communication BUS check screen for approximately 1 minute and check for ECUs and sensors that a not indicated on the screen.

  3. G029882
    "There is no system connected to the communication bus" is displayed if there are no ECUs or sensors connected to the CAN bus.


CHECK INSTALLED SYSTEMS (ECUS & SENSORS) THAT ADOPT CAN COMMUNICATION
  1. Systems (ECUs and sensors) that adopt CAN communication vary depending on the vehicle's optional settings. Check which systems (ECUs and sensors) are installed on the vehicle.

    ECU/Sensor name
    Check method
    Brake actuator (skid control ECU)
    With ABS
    ABS and traction actuator (skid control ECU)
    With VSC
    Steering sensor
    With VSC
    Yaw rate sensor
    With VSC
    ECM
    Installed on all vehicles
    Center airbag sensor assembly
    Installed on all vehicles
    Air conditioning amplifier
    With air conditioning (Auto air conditioning and manual air conditioning) or PTC heater
    Combination meter ECU
    Installed on all vehicles
    Main body ECU
    Installed on all vehicles
    Certification ECU
    With entry and start system
    Transmission control ECU
    With multi-mode manual transaxle


DTC TABLE BY ECU

HINT:
  1. In the CAN communication system, CAN communication system DTCs output by the ECU can be displayed by using the intelligent tester.
  2. If CAN communication system DTCs are output, trouble cannot be determined solely from the DTCs. Perform troubleshooting according to "HOW TO PROCEED WITH TROUBLESHOOTING "(Click here).

  1. BRAKE ACTUATOR (SKID CONTROL ECU)
    For vehicle with ABS only

    HINT:
    DTC communication uses the CAN communication system.
    DTC No.
    Detection Item
    U0073/94
    Control Module Communication Bus OFF

  2. ABS AND TRACTION ACTUATOR (SKID CONTROL ECU)
    For vehicle with VSC only

    HINT:
    DTC communication uses the CAN communication system.
    DTC No.
    Detection Item
    U0073/94
    Control Module Communication Bus OFF
    U0100/65
    Lost Communication with ECM/PCM
    U0123/62
    Lost Communication with Yaw Rate Sensor Module
    U0124/95*1
    Lost Communication with Lateral Acceleration Sensor Module
    U0124/69*2
    Deceleration Sensor Communication Malfunction
    U0126/63
    Lost Communication with Steering Angle Sensor Module
    *1: TMC Made
    *2: TMMF Made

  3. POWER STEERING ECU

    HINT:
    DTC communication uses the SIL line.
    DTC No.
    Detection Item
    U0073
    Control Module Communication Bus OFF
    U0105
    Lost Communication with ECM
    U0121
    Lost Communication with Anti-lock Brake System (ABS) Control Module

  4. COMBINATION METER ECU

    HINT:
    DTC communication uses the CAN communication system.
    DTC No.
    Detection Item
    U0100*1
    Lost Communication with ECM/PCM "A"
    U0129*2
    Lost Communication with Brake System Control Module

    HINT:
    1. *1: DTC U0100 is stored if communication cannot be established with the ECM at a vehicle speed of 5 km/h (3.2 mph) or more.
    2. *2: DTC U0129 is stored if communication cannot be established with the brake actuator (skid control ECU) during engine start.

    NOTICE:
    These DTSs may not be stored when the ignition switch is turned on (IG) or when the engine stops.

  5. AIR CONDITIONING AMPLIFIER
    For vehicle with air conditioning and PTC heater

    HINT:
    DTC communication uses the CAN communication system.
    DTC No.
    Detection Item
    B1499/99
    Multiplex Communication Circuit

  6. ECM

    HINT:
    DTC communication uses the SIL line. (1ND-TV engine only)

    DTC No.
    Detection Item
    U0101*1
    Lost Communication with TCM
    U0129*2
    Lost Communication with Skid Control ECU
    *1: For vehicle with multi-mode manual transaxle only.
    *2: For vehicle with 1KR-FE, 2SZ-FE and 1ND-TV engine only.

  7. TRANSMISSION CONTROL ECU
    For vehicle with multi-mode manual transaxle

    HINT:
    DTC communication uses the SIL line.
    DTC No.
    Detection Item
    U0100*
    Lost Communication with ECM/PCM "A"
    *: For vehicle with multi-mode manual transaxle only.

  8. CENTER AIRBAG SENSOR ASSEMBLY

    HINT:
    1. The center airbag sensor assembly is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "SRS Airbag" is not displayed on the "Communication Bus Check" screen on the intelligent tester, proceed to "Center Airbag Sensor Communication Stop Mode." (Click here)

  9. MAIN BODY ECU

    HINT:
    1. The main body ECU is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "Integrated J/B" is not displayed on the "Communication Bus Check" screen on the intelligent tester, proceed to "Main Body ECU Communication Stop Mode." (Click here)

  10. CERTIFICATION ECU
    For vehicle with entry and start system only

    HINT:
    1. The certification ECU is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "Entry & Start" is not displayed on the "Communication Bus Check" screen on the intelligent tester, proceed to "Certification ECU Communication Stop Mode." (Click here)


DTC COMBINATION TABLE
DTC
Trouble Mode
Output from
Output DTC
Brake Actuator (Skid Control ECU) Communication Stop Mode
ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode
Power Steering ECU Communication Stop Mode
Steering Angle Sensor Communication Stop Mode
Yaw Rate Sensor Communication Stop Mode
Center Airbag Sensor Communication Stop Mode
Brake Actuator (Skid Control ECU)
U0073/94
○*5
X
X
X
X
X
ABS and Traction Actuator (Skid Control ECU)
U0073/94
X
○*5
X
X
X
X
U0100/65
X
X
X
X
X
X
U0123/62
X
X
X
X
○
X
U0124/95*1
X
X
X
X
○
X
U0124/69*2
X
X
X
X
○
X
U0126/63
X
X
X
○
X
X
Power Steering ECU
U0073
X
X
○
X
X
X
U0105
X
X
○
X
X
X
U0121
○
○
○
X
X
X
Combination Meter ECU
U0100
X
X
X
X
X
X
U0129
○
○
X
X
X
X
Air Conditioning Amplifier
B1499/99
X
X
X
X
X
X
ECM
U0101*3
X
X
X
X
X
X
U0129*4
○
○
X
X
X
X
Transmission on Control ECU*3
U0100*3
X
X
X
X
X
X

HINT:
  1. ○: Outputs under conditions shown above
  2. X: Not output
  3. *1: TMC Made
  4. *2: TMMF Made
  5. *3: w/ Multi-mode manual transaxle
  6. *4: 1KR-FE, 2SZ-FE and 1ND-TV engine only
  7. *5: The brake actuator (skid control ECU) detects U0073/94 when DTC communication fails in succession. However, this DTC may not be output when the CAN communication system malfunctions.
  8. *6: This DTC is output when communication failures from the ECM and the combination meter ECU occur.

DTC
Trouble Mode
Output from
Output DTC
ECM Communication Stop Mode
Transmission Control ECU and ECM Communication Stop Mode
Air Conditioning Amplifier Communication Stop Mode
Combination Meter ECU Communication Stop Mode
Main Body ECU Communication Stop Mode
Certification ECU Communication Stop Mode
Brake Actuator (Skid Control ECU)
U0073/94
X
X
X
X
X
X
ABS and Traction Actuator (Skid Control ECU)
U0073/94
X
X
X
X
X
X
U0100/65
○
X
X
X
X
X
U0123/62
X
X
X
X
X
X
U0124/95*1
X
X
X
X
X
X
U0124/69*2
X
X
X
X
X
X
U0126/63
X
X
X
X
X
X
Power Steering ECU
U0073
X
X
X
X
X
X
U0105
○
X
X
X
X
X
U0121
X
X
X
X
X
X
Combination Meter ECU
U0100
○
X
X
X
X
X
U0129
X
X
X
X
X
X
Air Conditioning Amplifier
B1499/99
○*6
X
X
○*6
X
X
ECM
U0101*3
X
○
X
X
X
X
U0129*4
X
X
X
X
X
X
Transmission Control ECU*3
U0100*3
○
X
X
X
X
X

HINT:
  1. ○: Outputs under condition shown in above
  2. X: Not output
  3. *1: TMC Made
  4. *2: TMMF Made
  5. *3: w/ Multi-mode manual transaxle
  6. *4: 1KR-FE, 2SZ-FE and 1ND-TV engine only
  7. *5: The brake actuator (skid control ECU) detects U0073/94 when DTC communication fails in succession. However, this DTC may not be output when the CAN communication system malfunctions.
  8. *6: This DTC is output when communication failures from the ECM and the combination meter ECU occur.

  1. Perform troubleshooting according to the combination of DTCs output.

    1. Brake Actuator (Skid Control ECU) Communication Stop Mode: (Click here)
    2. ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode: (Click here)
    3. Power Steering ECU Communication Stop Mode: (Click here)
    4. Steering Angle Sensor Communication Stop Mode: (Click here)
    5. Yaw Rate Sensor Communication Stop Mode: (Click here)
    6. ECM Communication Stop Mode: (Click here)
    7. Center Airbag Sensor Communication Stop Mode: (Click here)
    8. Air Conditioning Amplifier Communication Stop Mode: (Click here)
    9. Combination Meter ECU Communication Stop Mode: (Click here)
    10. Main Body ECU Communication Stop Mode: (Click here)
    11. Certification ECU Communication Stop Mode: (Click here)
    12. Transmission Control ECU and ECM Communication Stop Mode: (Click here)

← TERMINALS OF ECU (from Aug 2005)FAIL-SAFE CHART (from Aug 2005) →