2005-2008 Yaris · Service Manual ENGINE

B2278 Engine Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

This DTC is output when 1) a malfunction is detected between the main body ECU and the ignition switch; or 2) either of the switches inside the ignition switch is malfunctioning.
DTC No.
DTC Detection Condition
Trouble Area
B2278
Communication is abnormal between main body ECU and ignition switch or ignition switch is defective
  1. Main body ECU
  2. Ignition switch
  3. Wire harness

WIRING DIAGRAM

B082265E01

INSPECTION PROCEDURE


1. READ VALUE OF INTELLIGENT TESTER (START SWITCH 1 AND 2)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Body / Main Body ECU / Data List / St SW1 and St SW2.

  1. Read the value displayed on the tester.

    Main Body ECU:
    Item
    Measurement Item/Display (Range)
    Normal Condition
    Diagnostic Note
    St SW1
    Start Switch 1 / ON or OFF
    ON: Ignition switch on (IG)
    OFF: Ignition switch off
    -
    St SW 2
    Start Switch 2 / ON or OFF
    ON: Ignition switch on (IG)
    OFF: Ignition switch off
    -

    OK:
    ON appears on the screen.



NG
Go to step 3
OK


2. CHECK SWITCH CONDITION (IGNITION SWITCH)
  1. Ensure the electrical key is inside the cabin.

  1. Check that the power source mode changes as shown below each time the ignition switch is.

OK:
off → on (ACC) → on (IG) → off



NG
GO TO POWER SOURCE MODE DOES NOT CHANGE
OK

SYSTEM IS OK

3. INSPECT IGNITION SWITCH ASSEMBLY
A109259E03
  1. Remove the ignition switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    7 (SS1) - 5 (GND)
    Pushed
    Below 1 Ω
    2 (SS2) - 5 (GND)
    Pushed
    Below 1 Ω
    7 (SS1) - 5 (GND)
    Not pushed
    10 kΩ or higher
    2 (SS2) - 5 (GND)
    Not pushed
    10 kΩ or higher

  1. Reinstall the ignition switch.



NG
REPLACE IGNITION SWITCH ASSEMBLY
OK


4. CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - MAIN BODY ECU AND BODY GROUND)

  1. A122232E01
    Disconnect the D55 ignition switch connector.

  1. Disconnect the D65 main body ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D55-7 (SS1) - D65-10 (SSW1)
    Below 1 Ω
    D55-2 (SS2) - D65-9 (SSW2)
    Below 1 Ω
    D55-5 (GND) - Body ground
    Below 1 Ω
    D55-7 (SS1) or D65-10 (SSW1) - Body ground
    10 kΩ or higher
    D55-2 (SS2) or D65-9 (SSW2) - Body ground
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the ignition switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← B2277 Detecting Vehicle Submersion (from Nov 2005)B2282 Vehicle Speed Signal Malfunction (+ B2283) (from Nov 2005) →