2005-2008 Yaris · Service Manual ENGINE

Engine does not Start

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION


ENGINE START SYSTEM OPERATION
  1. Except M/T: If the engine switch is pressed with the shift lever in P (A/T) or N and the brake pedal depressed, the main body ECU determines that it is an engine start request.

  2. M/T: When the ignition switch is pressed with the clutch pedal depressed, the main body ECU determines that it is an engine start request.

  3. The certification ECU and other ECUs perform key verification via the LIN communication line.

  4. The main body ECU activates the ACC cut relay.

  5. The main body ECU activates the IG1 and IG2 relays. The ignition switch indicator light illuminates green.

  6. The certification ECU outputs a steering UNLOCK signal. The signal is sent to the steering lock ECU via the main body ECU.

  7. The main body ECU sends an engine start request signal to the ECM.

  8. The ECM sends an ACC cut request signal to the main body ECU.

  9. The ECM and main body ECU activate the ST relay.

  10. The main body ECU deactivates the ACC cut relay until the ECU detects an engine start.

  11. The ECU reactivates the ACC cut relay and turns off the ignition switch indicator light.

    Symbols of main body ECU
    Signals
    SSW1/SSW2
    Ignition switch ON signal
    STP
    Stop light switch ON signal
    ACCD
    ACC cut relay operation signal
    IG2D
    IG2 relay operation signal
    STR2
    ST relay operation signal
    STR
    Clutch switch signal (M/T)
    ST relay operation signal (except M/T)
    TACH
    Engine start detection signal
    STSW
    Starter activation request signal
    ACCR
    ACC cut request signal

B127997E02

WIRING DIAGRAM

See CRANKING HOLDING FUNCTION CIRCUIT (Click here).

INSPECTION PROCEDURE


1. CHECK WHETHER ENGINE STARTS AFTER STEERING LOCK INITIALIZATION
  1. Open and close the driver door when the ignition switch is off.

  1. Check that the engine starts.

    OK:
    Engine starts.

HINT:
The engine may not start if the steering lock ECU has not been initialized through the procedure described in above after the battery runs out.



OK
SYSTEM OK
NG


2. CHECK WHETHER DTC OUTPUT RECURS
  1. Clear the DTCs.

    HINT:
    After all DTCs are cleared, check if the trouble occurs again 5 seconds after the ignition switch is turned on (IG).

  1. Check for DTCs again.

    OK:
    No DTC is output.



NG
GO TO DTC CHART
OK


3. CHECK SWITCH CONDITION
  1. Ensure the electrical key is inside the cabin.

  1. Check that the power source mode changes as shown below each time the ignition switch is.

OK:
off → on (ACC) → on (IG) → off



NG
GO TO POWER SOURCE MODE DOES NOT CHANGE
OK


4. CHECK BASIC FUNCTION
  1. Ensure there is fuel in the fuel tank and the key is inside the cabin.

  1. Depress the clutch pedal (M/T) or brake pedal (except M/T), and keep depressing the pedal.

  1. Check that the engine cranks when the ignition switch is pressed.

OK:
Engine cranks.



OK
Go to step 8
NG


5. READ VALUE OF INTELLIGENT TESTER (CLUTCH START SW, PARK/NEUTRAL POSITION SW AND STOP LIGHT SW)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. For except M/T:

    1. Select the following menu items: Body / Main Body ECU / Data List / Stop Lamp SW1.

    2. Read the display on the tester.

      Main body ECU:
      Item
      Measurement Item/Display (Range)
      Normal Condition
      Diagnostic Note
      Stop Lamp SW1
      Stop light switch 1/ ON or OFF
      ON: Brake pedal depressed
      OFF: Brake pedal released
      -

      OK:
      ON (brake pedal depressed) and OFF (brake pedal released) appear on the screen.

  1. Select the following menu items: Body / Main Body ECU / Data List / N SW / C SW.

  1. Read the display on the tester.

    Main body ECU:
    Item
    Measurement Item/Display (Range)
    Normal Condition
    Diagnostic Note
    N SW / C SW
    Clutch switch (M/T) or park/ neutral position switch (except M/ T)/ ON or OFF
    ON: Clutch pedal is depressed (M/T) or Shift position is N (except M/T)
    OFF: Clutch pedal is released or Shift position is except N (except M/T)
    -

    OK:
    ON (Clutch pedal is depressed (M/T) or Shift position is N (except M/T)) and OFF ( Clutch pedal is released or Shift position is except N (except M/T)) appear on the screen.



NG
REPAIR OR REPLACE CLUTCH START SWITCH
OK


6. CHECK STEERING LOCK SYSTEM
  1. When the ignition switch is on (ACC), check that the steering lock can be released.

    OK:
    Steering lock can be released.



NG
GO TO STEERING LOCK SYSTEM
OK


7. INSPECT MAIN BODY ECU

  1. A122230E01
    Disconnect the D66 main body ECU connector.

  1. Depress the clutch pedal (M/T) or brake pedal (except M/T), and keep depressing the pedal.

  1. Measure the voltage when the engine cranks by pressing the ignition switch.

    Standard voltage:
    Tester Connection
    Specified Condition
    STSW (D66-4) - Body ground
    10 to 14 V

  1. Reconnect the main body ECU connector.



NG
GO TO SFI SYSTEM (CRANKING HOLDING FUNCTION CIRCUIT)
OK

REPLACE MAIN BODY ECU

8. READ VALUE OF INTELLIGENT TESTER (L CODE CHECK)
  1. Placs the electrical key is inside the vehicle.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Body / Certification ECU / Data List / L Code Chk.

  1. Read the display on the tester.

    Main body ECU:
    Item
    Measurement Item / Display (Range)
    Normal Condition
    L Code Chk
    L Code Check / NG or OK
    NG: L code certification result is abnormal
    OK: L code certification result is normal

    OK:
    L code certification result is normal.



NG
GO TO ENGINE IMMOBILISER SYSTEM (STEERING LOCK ECU OR ID CODE BOX MALFUNCTIONS)
OK


9. READ VALUE OF INTELLIGENT TESTER (ENGINE START REQUEST)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON (not start the engine).

  1. Select the following menu items: Body / Certification ECU / Data List / Start Req Sig.

  1. Read the displays on the tester.

    Certification ECU:
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Start Req Sig
    Starter request signal / Yes or No
    Yes: ST relay is ON
    No: ST relay is OFF

    OK:
    ST relay is ON.



NO
REPLACE CERTIFICATION ECU
YES


10. READ VALUE OF INTELLIGENT TESTER (S CODE CHECK)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Body / Certification ECU / Data List / S Code Chk.

  1. Read the display on the tester.

    Certification ECU:
    Item
    Measurement Item / Display (Range)
    Normal Condition
    S Code Chk
    S Code Check / NG or OK
    NG: S code certification result is abnormal
    OK: S code certification result is normal

    OK:
    S code certification result is normal.



NG
GO TO ENGINE IMMOBILISER SYSTEM (CERTIFICATION ECU OR ID CODE BOX MALFUNCTIONS)
OK

REPLACE ID CODE BOX


← Power Source Mode does not Change (from Nov 2005)Engine Switch Indicator Circuit (from Nov 2005) →