2005-2008 Yaris · Service Manual ENGINE

Cranking Holding Function Circuit

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

The cranking holding control system keeps energizing the starter relay from when the ECM detects the starter signal (STSW signal) from the ignition switch or the main body ECU until the ECM performs a judgement of "Engine started". Furthermore, the ECM outputs an accessory cut signal (ACCR signal) to the ACC cut relay during cranking to prevent flickering of the combination meter, clock, audio system, and so on.
When the ECM detects the STSW signal, the ECM outputs the starter relay drive signal (STAR signal) to the starter relay through the clutch start switch or park/neutral position switch, and then, the engine is cranked. When the ECM receives a stable engine speed signal (NE signal), more specifically, when the NE signal reaches a predetermined value, the ECM stops outputting the STAR signal. Also, the ECM monitors the starter relay operating conditions based on the STA terminal voltage status.
A103821E16

WIRING DIAGRAM

A128481E01
A122549E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is turned on (IG) and the engine starts.

    Standard:
    Ignition Switch Conditions
    Tester Display (Starter Signal)
    On (IG)
    OFF
    Engine start
    ON



OK
Go to step 12
NG


2. INSPECT ECM (STSW TERMINAL VOLTAGE)
A115671E01
  1. Disconnect the A21 ECM connector.

  1. Depress the clutch pedal fully.

  1. Measure the voltage between the ECM terminal and the body ground when operating the ignition switch to start cranking.

    Standard voltage:
    Tester Connections
    Specified Conditions
    STSW (A21-14) - Body ground
    9 to 14 V

  1. Reconnect the ECM connector.

    Result:
    Result
    Proceed To
    Within standard range
    A
    Outside standard range (vehicle without entry and start system)
    B
    Outside standard range (vehicle with entry and start system)
    C



B
Go to step 5

C
Go to step 6
A


3. INSPECT ECM (STAR OUTPUT VOLTAGE)
A122550E01
  1. Inspect the clutch start switch (for Manual Transaxle models).

    1. Disconnect the clutch start switch connector.

    2. Measure the voltage between the terminal of clutch start switch connector and the body ground while cranking the engine.

      Standard voltage:
      Tester Connections
      Specified Conditions
      B (A16-2) - Body ground
      9 to 14 V

    3. Reconnect the clutch start switch connector.

  1. Inspect the Park/Neutral Position (PNP) switch (for Multi-mode Manual Transaxle models).

    1. Disconnect the PNP switch connector.

    2. Measure the voltage between the terminal of PNP switch connector and the body ground while cranking the engine.

      Standard voltage:
      Tester Connections
      Specified Conditions
      B (A43-2) - Body ground
      9 to 14 V

    3. Reconnect the PNP switch connector.

      Result:
      Result
      Proceed To
      Within standard range
      A
      Outside standard range (vehicle without entry and start system)
      B
      Outside standard range (vehicle with entry and start system)
      C



B
Go to step 7

C
Go to step 8
A


4. INSPECT PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH

  1. A122558E01
    Inspect the clutch start switch (for Manual Transaxle models).
    1. Disconnect the A16 clutch start switch connector.

    2. Check the resistance when the clutch start switch is ON and OFF.

      Standard resistance:
      Switch Conditions
      Tester Connections
      Specified Conditions
      ON (pushed)
      1 - 2
      Below 1 Ω
      OFF (free)
      1 - 2
      10 kΩ or higher

    3. Reconnect the clutch start switch connector.

  1. Inspect the Park/Neutral Position (PNP) switch (for Multi-mode Manual Transaxle models).

    1. Disconnect the A43 PNP switch connector.

    2. Check the PNP switch connector resistance.

      Standard resistance:
      Switch Conditions
      Tester Connections
      Specified Conditions
      Pushed
      1 - 2
      Below 1 Ω
      Free
      1 - 2
      10 kΩ or higher

    3. Reconnect the PNP switch connector.



OK
Go to step 12
NG

REPLACE PARK/NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH

5. INSPECT IGNITION SWITCH ASSEMBLY
A107906E03
  1. Remove the ignition switch assembly.

  1. Check the resistance between the terminals of ignition switch assembly.

    Standard resistance:
    Switch Positions
    Tester Connections
    Specified Conditions
    LOCK
    -
    10 kΩ or higher
    ACC
    2 - 4
    Below 1 Ω
    ON
    1 - 2 - 4
    5 - 6
    START
    1 - 3 - 4
    5 - 6 - 7

  1. Reinstall the ignition switch assembly.



NG
REPLACE IGNITION SWITCH ASSEMBLY
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - IGNITION SWITCH - BATTERY)

6. CHECK HARNESS AND CONNECTOR (ECM - MAIN BODY ECU)
A122540E02
  1. Disconnect the D66 main body ECU connector.

  1. Disconnect the A21 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    STSW (D66-4) - STSW (A21-14)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    STSW (D66-4) - Body ground
    Below 1 Ω

  1. Reconnect the main body ECU connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ENTRY AND START SYSTEM

7. CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - IG SWITCH AND ECM, OR PNP SWITCH - ECM)
A122541E01
  1. Check harness and connectors (for manual transaxle models).

    1. Disconnect the D8 ignition switch connector.

    2. Disconnect the A16 clutch start switch connector.

    3. Disconnect the C20 ECM connector.

    4. Check the resistance.

      Standard resistance (Check for open):
      Tester Connections
      Specified Conditions
      ST2 (D8-7) - B (A16-2)
      Below 1 Ω
      STAR (C20-52) - B (A16-2)

      Standard resistance (Check for short):
      Tester Connections
      Specified Conditions
      ST2 (D8-7) - Body ground
      10 kΩ or higher
      STAR (C20-52) - Body ground

      HINT:
      The wire between the clutch start switch and the ignition switch has a diode (refer to the wiring diagram). The current flowing to the clutch start switch is rectified by the diode.

    5. Reconnect the ignition switch connector.

    6. Reconnect the clutch start switch connector.

    7. Reconnect the ECM connector.

  1. Check harness and connectors (for multi-mode manual transaxle models).

    1. Disconnect the C20 ECM connector.

    2. Disconnect the A43 PNP switch connector.

    3. Check the resistance.

      Standard resistance (Check for open):
      Tester Connections
      Specified Conditions
      STAR (C20-52) - B (A43-2)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connections
      Specified Conditions
      STAR (C20-52) - Body ground
      10 kΩ or higher

    4. Reconnect the ECM connector.

    5. Reconnect the PNP switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

8. INSPECT ST CUT RELAY
B016200E02
  1. Remove the ST CUT relay.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    3 - 5
    10 kΩ or higher
    Below 1 Ω
    (When battery voltage applied to terminals 1 and 2)

  1. Reinstall the relay.



NG
REPLACE ST CUT RELAY
OK


9. INSPECT ST CUT RELAY (RELAY HOLDER TERMINAL VOLTAGE)
A122713E03
  1. Remove the ST CUT relay.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage between the terminals of the ST CUT relay holder.

    Standard voltage:
    Tester Connections
    Specified Conditions
    1 - 2
    9 to 14 V

  1. Reinstall the relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. CHECK HARNESS AND CONNECTOR (ST CUT RELAY - ECM, MAIN BODY ECU, PNP AND CLUTCH ST SWITCH)
A122542E01
  1. Remove the ST CUT relay.

  1. Disconnect the A16 clutch start switch connector (for manual transaxle models).

  1. Disconnect the A43 PNP switch connector (for multi-mode manual transaxle models).

  1. Disconnect the D66 main body ECU connector (for manual transaxle models).

  1. Disconnect the C20 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    ST CUT relay (D67-3) - STAR (C20-52)
    Below 1 Ω
    ST CUT relay (D67-3) - STR2 (D66-14)
    STR (D66-3) - ST CUT relay (D67-5)
    B (A16-2) or B (A43-2) - ST CUT relay (D67-5)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    ST CUT relay (D67-3) - Body ground
    10 kΩ or higher
    ST CUT relay (D67-5) - Body ground

  1. Reconnect the ECM connector.

  1. Reconnect the main body ECU connector.

  1. Reconnect the PNP switch connector.

  1. Reconnect the clutch start switch connector.

  1. Reinstall the ST CUT relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. INSPECT MAIN BODY ECU (CHECK FOR SHORT)
A122713E04
  1. Disconnect the C20 ECM connector.

  1. Remove the ST CUT relay.

  1. Check the resistance between the terminals of the ST CUT relay holder.

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    ST CUT relay (D67-3) - Body ground
    10 kΩ or higher
    ST CUT relay (D67-5) - Body ground

  1. Reinstall the ST CUT relay.

  1. Reconnect the ECM connector.



NG
CHECK ENTRY AND START SYSTEM
OK

REPLACE ECM

12. CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH OR PNP SWITCH - ECM - ST RELAY)
A122543E01
  1. Remove the ST relay from the engine room relay block.

  1. Disconnect the A16 clutch start switch connector (for manual transaxle models).

  1. Disconnect the A43 PNP switch connector (for multi-mode manual transaxle models).

  1. Disconnect the A21 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    L (A16-1) or L (A43-1) - STA (A21-48)
    Below 1 Ω
    L (A16-1) or L (A43-1) - ST relay (2)
    ST relay (1) - Body ground

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    L (A16-1) or L (A43-1) - Body ground
    10 kΩ or higher

  1. Reinstall the ST relay.

  1. Reconnect the clutch start switch connector.

  1. Reconnect the PNP switch connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13. INSPECT BATTERY
  1. Check that the battery is not depleted.

    OK:
    Battery is not depleted.



NG
REPLACE BATTERY
OK


14. CHECK BATTERY TERMINAL
  1. Check that the battery terminals are not loose or corroded.

    OK:
    Battery terminals are not loose or corroded.



NG
CHECK AND REPLACE STARTER CIRCUIT (STARTER - ST RELAY - BATTERY)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR


← Fuel Pump Control Circuit (from Nov 2005)MIL Circuit (from Nov 2005) →