Engine does not Start
Circuit diagnosis · Vehicles built from Nov 2006
DESCRIPTION
| ENGINE START SYSTEM OPERATION |
When the engine switch is pressed with the clutch pedal depressed, the main body ECU determines that it is an engine start request.
The certification ECU and other ECUs perform key verification via the LIN communication line.
The main body ECU activates the ACC relay.
The main body ECU activates the IG1 and IG2 relays. The engine switch indicator light illuminates green.
The certification ECU outputs a steering UNLOCK signal. The signal is sent to the steering lock ECU via the main body ECU.
The main body ECU sends an engine start request signal to the ECM.
The ECM sends an ACC request signal to the main body ECU.
The ECM and main body ECU activate the ST cut relay.
The main body ECU deactivates the ACC relay until the ECU detects an engine start.
The ECU reactivates the ACC relay and turns off the engine switch indicator light.
Symbols of main body ECU
Signals
SSW1/SSW2
Engine switch ON signal
STP
Stop light switch ON signal
ACCD
ACC relay operation signal
IG2D
IG2 relay operation signal
STR2
ST cut relay operation signal
STR
Clutch switch signal
TACH
Engine start detection signal
STSW
Starter activation request signal
ACCR
ACC request signal


WIRING DIAGRAM
See CRANKING HOLDING FUNCTION CIRCUIT (Click here).INSPECTION PROCEDURE
| 1. CHECK WHETHER ENGINE STARTS AFTER STEERING LOCK INITIALIZATION |
Open and close the driver door when the engine switch is off.
Check that the engine starts.
- OK:
- Engine starts.
- HINT:
- The engine may not start if the steering lock ECU has not been initialized through the procedure described in above after the battery runs out.
|
|
||||
| NG | |
| 2. CHECK WHETHER DTC OUTPUT RECURS |
Clear the DTCs.
- HINT:
- After all DTCs are cleared, check if the trouble occurs again 5 seconds after the engine switch is turned on (IG).
Check for DTCs again.
- OK:
- No DTC is output.
|
|
||||
| OK | |
| 3. CHECK SWITCH CONDITION |
Ensure the electrical key is inside the cabin.
Check that the power source mode changes as shown below each time the engine switch is.
- OK:
- off → on (ACC) → on (IG) → off
|
|
||||
| OK | |
| 4. CHECK BASIC FUNCTION |
Ensure there is fuel in the fuel tank and the key is inside the cabin.
Depress the clutch pedal, and keep depressing the pedal.
Check that the engine cranks when the engine switch is pressed.
- OK:
- Engine cranks.
|
|
||||
| NG | |
| 5. READ VALUE OF INTELLIGENT TESTER (CLUTCH START SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester ON.
Select the following menu items: Body / Main Body ECU / Data List / N SW / C SW.
Read the display on the tester.
- Main body ECU:
Item
Measurement Item/Display (Range)
Normal Condition
Diagnostic Note
N SW / C SW
Clutch switch
ON: Clutch pedal is depressed
OFF: Clutch pedal is released
-
- OK:
- ON (Clutch pedal is depressed) and OFF (Clutch pedal is released) appear on the screen.
|
|
||||
| OK | |
| 6. CHECK STEERING LOCK SYSTEM |
When the engine switch is on (ACC), check that the steering lock can be released.
- OK:
- Steering lock can be released.
|
|
||||
| OK | |
| 7. INSPECT MAIN BODY ECU |
Disconnect the D66 main body ECU connector.

Depress the clutch pedal and keep depressing the pedal.
Measure the voltage when the engine cranks by pressing the engine switch.
- Standard voltage:
Tester Connection
Specified Condition
D66-4 (STSW) - Body ground
11 to 14 V
Reconnect the main body ECU connector.
|
|
||||
| OK | ||
| ||
| 8. READ VALUE OF INTELLIGENT TESTER (L CODE CHECK) |
Ensure the key is inside the cabin.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester ON.
Select the following menu items: Body / Certification ECU / Data List / L Code Chk.
Read the display on the tester.
- Main body ECU:
Item
Measurement Item / Display (Range)
Normal Condition
L Code Chk
L Code Check / NG or OK
NG: L code certification result is abnormal
OK: L code certification result is normal
- OK:
- L code certification result is normal.
|
|
||||
| OK | |
| 9. READ VALUE OF INTELLIGENT TESTER (ENGINE START REQUEST) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester ON (not start the engine).
Select the following menu items: Body / Certification ECU / Data List / Start Req Sig.
Read the displays on the tester.
- Certification ECU:
Item
Measurement Item / Display (Range)
Normal Condition
Start Req Sig
Starter request signal / Yes or No
Yes: ST relay is ON
No: ST relay is OFF
- OK:
- ST relay is ON.
|
|
||||
| YES | |
| 10. READ VALUE OF INTELLIGENT TESTER (S CODE CHECK) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester ON.
Select the following menu items: Body / Certification ECU / Data List / S Code Chk.
Read the display on the tester.
- Certification ECU:
Item
Measurement Item / Display (Range)
Normal Condition
S Code Chk
S Code Check / NG or OK
NG: S code certification result is abnormal
OK: S code certification result is normal
- OK:
- S code certification result is normal.
|
|
||||
| OK | ||
| ||
