2005-2008 Yaris · Service Manual BODY ELECTRICAL

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Aug 2005


INSPECT ENTRY AND START SYSTEM
  1. Check the entry unlock function.

    1. Use the wireless lock operation to lock the doors. With the electrical key in your possession, touch the outside handle (touch sensor) of a door and check that the door unlocks.

  1. B109835E01
    Check the entry unlock operation detection area.

    1. Step 1: Hold the electrical key at the same height as the door's outside handle (approximately 0.8 m (2.6 ft.)) in the direction of the key in the illustration.

    2. Step 2: Check that the system enters unlock standby mode when the electrical key is brought within 0.7 to 1.0 m (2.3 to 3.3 ft.) of the vehicle.

      HINT:
      Unlock standby mode is signified by the illumination of the electrical key's red LED.

    3. Step 3: After the system enters unlock standby mode, touch the door outside handle's sensor within 3 seconds. Check that the door unlocks.

    4. E107177E02
      Step 4: Repeat step 2 and step 3 for the remaining doors.

    5. Step 5: Inspect the door electrical key oscillator's response sensitivity. Wear protective gloves, set the system to unlock standby mode, and check that touching the inner side of the door outside handle (the highlighted area in the illustration) with your finger causes the door to unlock.

      NOTICE:
      When touching the highlighted area, tapping too quickly or having extended contact may not trigger the sensor. In such a case, the door will not unlock.

    6. Step 6: Repeat step 5 for the remaining doors.

  1. Check the entry lock function.

    1. B127157E01
      Step 1: Close all of the vehicle's doors. With the electrical key in your possession outside of the vehicle, check that pressing the lock switch locks the doors.

    2. Step 2: Inspect the entry lock operation detection area and the indoor electrical key oscillator for wave leaks. Hold the electrical key at a height of 1 m (3.3 ft.) (0.1 m (0.3 ft.) above the lower edge of the window frame), in the direction and position of the electrical key in the illustration. Check that when the electrical key is approximately 0.3 m (0.9 ft.) from the vehicle and the lock switch is pressed, the front doors lock and the warning buzzer (for when the electrical key is forgotten) does not sound. If the warning buzzer sounds, the indoor electrical key oscillator may have a wave leak.

      HINT:
      Due to the electrical key being unable to communicate with the system within a 0.2 m (0.6 ft.) distance from the door outside handle, do not press the lock switch with the same hand that is holding the key. The doors will not lock.

    3. Step 3: Repeat step 1 and step 2 for the remaining doors.

  1. Check the entry back door open function.

    1. B109837E01
      Close the back door. With the electrical key in your possession, check that pressing the back door unlock switch opens the back door.

    2. Inspect the back door open operation's detection area. Hold the electrical key at the same height as the back door open switch (approximately 0.8 m (2.6 ft.)), in the direction of the key shown in the illustration. Check that the when the key is brought within 0.7 to 1.0 m (2.3 to 3.3 ft.) of the vehicle, pressing the back door unlock switch opens the back door.

  1. Check the entry ignition function.

    1. When the engine is off:
      With the electrical key in your possession and the clutch pedal depressed, check that pressing the ignition switch releases the steering wheel lock and starts the engine.

      HINT:
      The engine can be started only when the ignition switch indicator illuminates in green.

    2. B109836E01
      When the engine is running:
      With the electrical key in your possession, check that pressing the ignition switch stops the engine and activates the steering wheel lock.

    3. Inspect the entry ignition operation detection area. Pay attention to the direction of the electrical key in the illustration. When the electrical key is in either of the 2 locations in the illustration, check that the engine can be started.

      NOTICE:
      The engine cannot be started when the electrical key is on the instrument panel or rear package tray, or in the glove box.

  1. Check the key cancel function.

    1. While the key cancel function (entry and start system cancel function) is ON, check that none of the functions in the entry and start system can be operated.

  1. Check the answer-back function (hazard warning light flashing and buzzer sounding).

    Entry Operation
    Hazard Warning Light
    Buzzer
    Entry Door Lock
    Flashes once
    Sounds once
    Entry Door Unlock
    Flashes twice
    Sounds twice

  1. Check that the warning buzzer (interior) sounds.

    1. Carry the electrical key in the vehicle and close the driver side door. Then turn the ignition switch off or on (ACC).

    2. Open the driver side door and check that the buzzer sounds intermittently.

  1. Check that the warning buzzer (interior) stops.

    1. When the buzzer is sounding, check that the buzzer stops sounding if either of the following is performed:

      1. The driver side door is closed (front door courtesy switch is off).
      2. The ignition switch is turned on (IG).

← DATA LIST / ACTIVE TEST (from Aug 2005)Wireless Door Lock Buzzer Does not Sound (from Aug 2005) →