2005-2008 Yaris · Service Manual RESTRAINTS

B1860/64 Short in Driver Side Knee Airbag Squib Circuit

Diagnostic trouble codes · Vehicles built from Aug 2005

Also covers:

DESCRIPTION

The driver side knee airbag squib circuit consists of the center airbag sensor assembly and the driver side knee airbag assembly.
This circuit signals the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side knee airbag squib circuit.
 
DTC No.
DTC Detecting Condition
Trouble Area
B1860/64
  1. Center airbag sensor assembly detects line short circuit signal 5 times in driver side knee airbag squib circuit during primary check.
  2. Driver side knee airbag squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Driver side knee airbag assembly (Driver side knee airbag squib)
  3. Center airbag sensor assembly
B1861/64
  1. Center airbag sensor assembly detects open circuit signal in driver side knee airbag squib circuit for 2 seconds.
  2. Driver side knee airbag squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Driver side knee airbag assembly (Driver side knee airbag squib)
  3. Center airbag sensor assembly
B1862/64
  1. Center airbag sensor assembly detects short circuit to ground signal in knee airbag (D side) squib circuit for 0.5 seconds.
  2. Driver side knee airbag squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Driver side knee airbag assembly (Driver side knee airbag squib)
  3. Center airbag sensor assembly
B1863/64
  1. Center airbag sensor assembly detects short circuit to B+ signal in knee airbag (D side) squib circuit for 0.5 seconds.
  2. Driver side knee airbag squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Driver side knee airbag assembly (Driver side knee airbag squib)
  3. Center airbag sensor assembly

WIRING DIAGRAM

H101438E01

INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting CHECK MODE (signal check) with the intelligent tester (Click here).
  2. After selecting CHECK MODE (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).


1. CHECK DRIVER SIDE KNEE AIRBAG ASSEMBLY (DRIVER SIDE KNEE AIRBAG SQUIB)
SST
09843-18060  

  1. C109509E03
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connector from the driver side knee airbag assembly.

  1. Connect the white wire side of SST (resistance 2.1 Ω) to the floor wire.

    CAUTION:
    Never connect a tester to the driver side knee airbag assembly (drive side knee airbag squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert the SST into the terminals of the connector when connecting.
    2. Insert the SST straight into the terminals of the connector.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1860, B1861, B1862, B1863 and 64 are not output.

    HINT:
    DTCs other than DTC B1860, B1861, B1862, B1863 and 64 may be output at this time, but they are not related to this check.



OK
REPLACE DRIVER SIDE KNEE AIRBAG ASSEMBLY
NG


2. CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the SST from connector C.

  1. Check that the instrument panel wire connector (on the driver side knee airbag assembly side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


3. CHECK INSTRUMENT PANEL WIRE (DRIVER SIDE KNEE AIRBAG SQUIB CIRCUIT)

  1. H044037E06
    Disconnect the connectors from the center airbag sensor assembly.

  1. Check for short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

    2. Turn the ignition switch on (IG).

    3. Measure the voltage.

      Standard voltage:
      Tester connection
      Condition
      Specified condition
      D68-1 (DK+) -
      Body ground
      Ignition switch on (IG)
      Below 1 V
      D68-2 (DK-) -
      Body ground
      Ignition switch on (IG)
      Below 1 V

  1. Check for open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance.

      Standard resistance:
      Tester connection
      Condition
      Specified condition
      D68-1 (DK+) -
      D68-2 (DK-)
      Always
      Below 1 Ω

  1. Check for short to ground in the circuit.

    1. Measure the resistance.

      Standard resistance:
      Tester connection
      Condition
      Specified condition
      D68-1 (DK+) -
      Body ground
      Always
      1 MΩ or higher
      D68-2 (DK-) -
      Body ground
      Always
      1 MΩ or higher

  1. Check for short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance.

      Standard resistance:
      Tester connection
      Condition
      Specified condition
      D68-1 (DK+) -
      D68-2 (DK-)
      Always
      1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


4. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. H046005E02
    Connect the connectors to the driver side knee airbag assembly and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1860, B1861, B1862, B1863 and 64 are not output.

    HINT:
    DTCs other than DTC B1860, B1861, B1862, B1863 and 64 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK


← B1835/58 Short in Front Passenger Side Curtain Shield Squib Circuit (+ B1836/58, B1837/58, B1838/58) (from Aug 2005)B1900/73 Short in Front Driver Side Pretensioner Squib Circuit (+ B1901/73, B1902/73, B1903/73) (from Aug 2005) →