Only Wireless Control Function is Inoperative
Circuit diagnosis · Vehicles built from Aug 2005
DESCRIPTION
The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. The main body ECU then controls all doors by sending lock / unlock signals to each door, and sends hazard flasher relay signals to the turn signal flasher relay (hazard warning lights).WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS |
- OK:
- Each function of wireless door lock control system operates normally using transmitter switches (Click here).
|
|
||||
| NG | |
| 2. CHECK TRANSMITTER LED ILLUMINATION |
Check that the transmitter's LED illuminates 3 times when the switch is pressed 3 times.
- OK:
- Transmitter's LED illuminates 3 times when switch is pressed 3 times.
|
|
||||
| OK | |
| 3. CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS (STANDARD OPERATION FUNCTION) |
- HINT:
- Use the following standard test procedure to check the transmitter again.
Hold the transmitter approximately 1 m (3.28 ft.) from the driver side door outside handle. The transmitter must be held parallel to the ground and perpendicular to the side of the vehicle.
Press and hold either the LOCK or UNLOCK transmitter switch for 1 second, and check that the doors are locked or unlocked, accordingly.
- OK:
- Doors can be locked and unlocked with transmitter switches (Click here).
|
|
||||
| OK | ||
| ||
| 4. REPLACE TRANSMITTER BATTERY |
After replacing the transmitter battery, check that the doors can be locked and unlocked using the transmitter switches.
- OK:
- Doors can be locked and unlocked with transmitter (Click here).
|
|
||||
| OK | ||
| ||
| 5. CHECK NO. 1 ROOM LIGHT ASSEMBLY |
Check that the No. 1 room light illumination operates normally.
- OK:
- No. 1 room light illumination operates normally.
|
|
||||
| OK | |
| 6. SWITCH TO SELF DIAGNOSTIC MODE |
Switch to self-diagnostic mode by operating the ignition key cylinder.
Make sure the vehicle is in its initial condition. Then insert the key into the ignition key cylinder and remove it.
Within 5 seconds of removing the key, insert the key into the ignition key cylinder (ignition switch off). Then turn the ignition switch on (IG) and off.
Within 30 seconds of turning the ignition switch off, perform the following 9 operation times: turn the ignition switch on (IG) and off.
- NOTICE:
- If the system cannot enter self-diagnostic mode, the system returns to normal mode.
- HINT:
- Turning the ignition switch on (IG) after the above operations have been completed ends self-diagnostic mode.
- Do not lock or unlock doors during self-diagnostic mode.
- Turning the ignition switch on (IG) after the above operations have been completed ends self-diagnostic mode.
Check that the system has switched to self-diagnostic mode by checking the No. 1 room light assembly flash pattern.

- OK:
- Flash pattern is same as illustration on left.
|
|
||||
| OK | |
| 7. CHECK BY SELF DIAGNOSTIC MODE |
Inspect the diagnosis outputs when the door control transmitter switch is held down. The diagnosis outputs can be checked by the flash patterns of the No. 1 room light assembly.


Result: Result
Proceed to
Unmatching recognition code is output
A
Normal waves (light flash patterns) for LOCK and UNLOCK switches are output
B
No diagnosis outputs
C
|
|
||||
|
|
||||
| A | |
| 8. REGISTER RECOGNITION CODE |
Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.
- OK:
- Recognition code can be registered.
|
|
||||
| OK | ||
| ||
| 9. CHECK RESPONSE OF DOOR CONTROL RECEIVER |
When a new or normally functioning door lock control transmitter switch for the same type vehicle is held down, check that an unmatching recognition code is output.
- OK:
- Unmatching recognition code is output.
|
|
||||
| NG | |
| 10. REPLACE DOOR CONTROL RECEIVER |
After replacing the door control receiver, check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.
- OK:
- Doors can be locked and unlocked with transmitter.
|
|
||||
| OK | ||
| ||
| 11. CONFIRM PROCEDURES TO ENTER SELF DIAGNOSTIC MODE |
- Result:
Result
Proceed to
Self-diagnostic mode entry successful
A
Self-diagnostic mode entry unsuccessful
B
|
|
||||
| A | |
| 12. INSPECT UNLOCK WARNING SWITCH ASSEMBLY |
Remove the unlock warning switch.
Measure the resistance.

- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Not pushed
10 kΩ or higher
Pushed
Below 1 Ω
|
|
||||
| OK | |
| 13. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - MAIN BODY ECU) |
Disconnect the D33 main body ECU connector.

Disconnect the J13 door control receiver connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
D33-16 (RDA) - J13-2 (RDA)
Below 1 Ω
D33-16 (RDA) - Body ground
10 kΩ or higher
D33-17 (PRG) - J13-3 (PRG)
Below 1 Ω
D33-17 (PRG) - Body ground
10 kΩ or higher
Reconnect the main body ECU connector.
Reconnect the door control receiver connector.
|
|
||||
| OK | |
| 14. CHECK DOOR CONTROL RECEIVER (OUTPUT) |
Measure the voltage.

- Standard voltage:
Tester Connection
Condition
Specified Condition
J13-2 (RDA) - Body ground
Transmitter switch ON→OFF (No key in ignition key cylinder, all doors closed)
Below 1 V → 6 to 7 V → Below 1 V
|
|
||||
| NG | |
| 15. REPLACE DOOR CONTROL TRANSMITTER MODULE |
Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.
- OK:
- Doors can be locked and unlocked with transmitter.
|
|
||||
| OK | ||
| ||
