2005-2008 Yaris · Service Manual BODY ELECTRICAL

Only Wireless Control Function is Inoperative

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. The main body ECU then controls all doors by sending lock / unlock signals to each door, and sends hazard flasher relay signals to the turn signal flasher relay (hazard warning lights).

WIRING DIAGRAM

B105509E01

INSPECTION PROCEDURE


1. CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

OK:
Each function of wireless door lock control system operates normally using transmitter switches (Click here).



OK
END
NG


2. REPLACE TRANSMITTER BATTERY
  1. After replacing the transmitter battery, check that the doors can be locked and unlocked using the transmitter switches.

    OK:
    Doors can be locked and unlocked with transmitter (Click here).



OK
REPLACE TRANSMITTER BATTERY
NG


3. SWITCH TO SELF DIAGNOSTIC MODE

  1. B110075E08
    Switch to self-diagnostic mode.
    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    3. Check that the system has switched to self-diagnostic mode by checking the sounding pattern of the buzzer of the wireless door lock.

      OK:
      Buzzer sounding pattern is same as illustration on left.



NG
Go to step 12
OK


4. CHECK BY SELF DIAGNOSTIC MODE

  1. Check the diagnostic outputs when the door control transmitter switch is held down. The diagnostic outputs can be checked by the sounding pattern of the buzzer of the wireless door lock.B123864E02

    Result: 
    Result
    Proceed to
    Unmatching recognition code is output
    A
    Normal waves (light flash patterns) for LOCK and UNLOCK switches are output
    B
    No diagnosis outputs
    C



B
REPLACE MAIN BODY ECU

C
Go to step 6
A


5. REGISTER RECOGNITION CODE
  1. Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.

    OK:
    Recognition code can be registered.



NG
Go to step 11
OK

END

6. CHECK RESPONSE OF DOOR CONTROL RECEIVER
  1. When a new or normally functioning door lock control transmitter switch for the same type vehicle is held down, check that an unmatching recognition code is output.

    OK:
    Unmatching recognition code is output.



OK
REPLACE DOOR CONTROL TRANSMITTER MODULE
NG


7. CHECK DOOR CONTROL RECEIVER (OUTPUT)

  1. B111368E05
    Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    J13-4 (+5) - Body ground
    Ignition switch off, all doors closed and transmitter switch not pressed → pressed
    5 to 0V → 5 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU)

  1. B123844E01
    Disconnect the D60 certification ECU connector.

  1. Disconnect the J13 door control receiver connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    D60-38 (RDA) - J13-5 (DATA)
    Below 1 Ω
    D60-38 (RDA) or J13-5 (DATA) - Body ground
    10 kΩ or higher
    D60-39 (RSSI) - J13-2 (RSSI)
    Below 1 Ω
    D60-39 (RSSI) or J13-2 (RSSI) - Body ground
    10 kΩ or higher
    D60-29 (RCO) - J13-4 (+5)
    Below 1 Ω
    D60-29 (RCO) or J13-4 (+5) - Body ground
    10 kΩ or higher

  1. Reconnect the certification ECU connector.

  1. Reconnect the door control receiver connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - MAIN BODY ECU)

  1. A122425E05
    Disconnect the 4D main body ECU connector.

  1. Disconnect the D60 certification ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    4D-9 (LIN1) - D60-10 (LIN)
    Below 1 Ω
    4D-9 (LIN1) or D60-10 (LIN) - Body ground
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the certification ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. REPLACE DOOR CONTROL RECEIVER
  1. After replacing the door control receiver, check that the doors can be locked and unlocked by using the transmitter LOCK and UULOCK switches.

    OK:
    Doors can be locked and unlocked with transmitter.



OK
END
NG


11. REPLACE CERTIFICATION ECU
  1. After replacing the certification ECU, check that the doors can be locked and unlocked by using the transmitter LOCK and UULOCK switches.

    OK:
    Doors can be locked and unlocked with transmitter.



NG
REPLACE MAIN BODY ECU
OK

END

12. CONFIRM PROCEDURES TO ENTER SELF DIAGNOSTIC MODE
Result: 
Result
Proceed to
Self-diagnostic mode entry successful
A
Self-diagnostic mode entry unsuccessful
B


B
Go to step 3
A

REPLACE MAIN BODY ECU


← B1242 Wireless Door Lock Tuner Circuit Malfunction (from Aug 2005)No Answer-Back (from Aug 2005) →