2005-2008 Yaris · Service Manual BODY ELECTRICAL

B1242 Wireless Door Lock Tuner Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2005

DESCRIPTION

The door control receiver receives lock/unlock signals from the transmitter and sends these signals to the main body ECU via the certification ECU using the serial line.
The main body ECU then activates the door lock motor on each door in accordance with these signals.
DTC No.
DTC Detection Condition
Suspected Area
B1242
  1. Short in RDA or RSSI ground between certification ECU and door control receiver
  2. Short in RDA or RSSI ground when RCO (5 V) output from ECU off
  1. Wire harness
  2. Door control receiver
  3. Certification ECU
  4. Main body ECU

WIRING DIAGRAM

B105509E01

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU)

  1. B123844E01
    Disconnect the D60 certification ECU connector.

  1. Disconnect the J13 door control receiver connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    D60-38 (RDA) - J13-5 (DATA)
    Below 1 Ω
    D60-38 (RDA) or J13-5 (DATA) - Body ground
    10 kΩ or higher
    D60-39 (RSSI) - J13-2 (RSSI)
    Below 1 Ω
    D60-39 (RSSI) or J13-2 (RSSI) - Body ground
    10 kΩ or higher
    D60-29 (RCO) - J13-4 (+5)
    Below 1 Ω
    D60-29 (RCO) or J13-4 (+5) - Body ground
    10 kΩ or higher

  1. Reconnect the certification ECU connector.

  1. Reconnect the door control receiver connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - CERTIFICATION ECU)

  1. A122425E04
    Disconnect the 4D main body ECU connector.

  1. Disconnect the D60 certification ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    4D-9 (LIN1) - D60-10 (LIN)
    Below 1 Ω
    4D-9 (LIN1) or D60-10 (LIN) - Body ground
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the certification ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT DOOR CONTROL RECEIVER (+B TERMINAL)

  1. B111368E05
    Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    J13-4 (+5) - Body ground
    Ignition switch off, all doors closed and transmitter switch not pressed → pressed
    5 to 0V → 5 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+B CIRCUIT)
OK


4. INSPECT DOOR CONTROL RECEIVER (GND TERMINAL)
  1. Disconnect the J13 door control receiver connector.

  1. B110096E03
    Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    J13-1 (GND) - Body ground
    Below 1 Ω

  1. Reconnect the door control receiver connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (E CIRCUIT)
OK


5. REPLACE DOOR CONTROL RECEIVER
  1. Replace the door control receiver.

  1. Perform the REGISTRATION procedures.

    HINT:
    If a new or normal functioning door control receiver is available, connect it and check if the wireless door lock function is normal or the DTC is output. If the alternative receiver functions normally, replace the original door control receiver.


NEXT


6. RECHECK DTC
  1. Clear the DTC.

  1. Check if the same DTC is detected.

    HINT:
    Reinstall the parts, such as sensors and connectors, and restore the vehicle to its previous conditions before rechecking for DTCs.

    Result: 
    Condition
    Proceed to
    DTC (B1242) is output
    A
    DTC (B1242) is not output (When troubleshooting in accordance with the DTC CHART)
    B
    DTC (B1242) is not output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE)
    C



B
END

C
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
A

REPLACE CERTIFICATION ECU


← ON-VEHICLE INSPECTION (from Aug 2005)Only Wireless Control Function is Inoperative (from Aug 2005) →