2005-2008 Yaris · Service Manual BODY ELECTRICAL

Double Lock Function does not Operate Properly

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

All the doors except the back door have the double lock function. This system is set and unset by the double door lock ECU. When the double door lock ECU receives a request signal from the wireless transmitter to set or unset the double lock function via the main body ECU, it drives the double door lock motor built into each door lock motor according to the conditions of the double door lock position switches, causing the double locking system to be set or unset.

WIRING DIAGRAM

B126156E02
B126157E01

INSPECTION PROCEDURE


1. CHECK DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Body / Main body ECU / DTC.

  1. Read DTCs.

    Result:
    Display (DTC output)
    Proceed To
    No DTC output
    A
    DTCs output
    B



B
GO TO DTC CHART
A


2. CHECK DOOR LOCK OPERATION

Result:
Result
Proceed to
The double lock function of the driver side front door does not operate properly.
A
The double lock function of the passenger side front door does not operate properly.
B
The double lock function of the rear RH door does not operate properly.
C
The double lock function of the rear LH door does not operate properly.
D



B
Go to step 6

C
Go to step 9

D
Go to step 12
A


3. INSPECT FRONT DOOR LOCK ASSEMBLY (DRIVER SIDE) (DOUBLE DOOR LOCK MOTOR)

  1. B118056E01
    Check the operation of the double lock motor.
    1. Apply the battery voltage to the door lock and set the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1
      Lock
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 2
      Unlock

    2. Apply the battery voltage to the door lock motor and check the operation of the double door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 3
      Set
      Battery positive (+) → Terminal 3
      Battery negative (-) → Terminal 4
      Unset

    3. While the double locking system is set, check that the doors cannot be unlocked by operating the control cable.



NG
REPLACE FRONT DOOR LOCK ASSEMBLY
OK


4. INSPECT FRONT DOOR LOCK ASSEMBLY (DRIVER SIDE) (DOUBLE DOOR LOCK POSITION SWITCH)
B118056E01
  1. Measure the resistance of the double door lock position switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    9 - 10
    Set
    Below 1 Ω
    9 - 10
    Unset
    10 kΩ or higher



NG
REPLACE FRONT DOOR LOCK ASSEMBLY
OK


5. CHECK HARNESS AND CONNECTOR (DOUBLE DOOR LOCK ECU - DOOR LOCK ASSEMBLY (DRIVER SIDE))
B127314E05
  1. Disconnect the D69 double door lock ECU connector.

  1. Disconnect the F5 door lock connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D69-3 (ACTS) - F5-4 (DL)
    Below 1 Ω
    D69-4 (ACTR) - F5-3 (UNDL)
    Below 1 Ω
    D69-5 (DLPD) - F5-9 (DLSR)
    Below 1 Ω
    F5-10 (E) - Body ground
    Below 1 Ω
    D69-3 (ACTS) or F5-4 (DL) - Body ground
    10 kΩ or higher
    D69-4 (ACTR) or F5-3 (UNDL) - Body ground
    10 kΩ or higher
    D69-5 (DLPD) or F5-9 (DLSR) - Body ground
    10 kΩ or higher

  1. Reconnect the double door lock ECU connector.

  1. Reconnect the door lock connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DOUBLE DOOR LOCK ECU

6. INSPECT FRONT DOOR LOCK ASSEMBLY (PASSENGER SIDE) (DOUBLE DOOR LOCK MOTOR)

  1. B118055E01
    Check the operation of the double door lock motor.
    1. Apply the battery voltage to the door lock and set the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 3
      Lock
      Battery positive (+) → Terminal 3
      Battery negative (-) → Terminal 4
      Unlock

    2. Apply the battery voltage to the door lock motor and check the operation of the double door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1
      Set
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 2
      Unset

    3. While the double locking system is set, check that the doors cannot be unlocked by operating the control cable.



NG
REPLACE FRONT DOOR LOCK ASSEMBLY
OK


7. INSPECT FRONT DOOR LOCK ASSEMBLY (PASSENGER SIDE) (DOUBLE DOOR LOCK POSITION SWITCH)
B118055E01
  1. Measure the resistance of the double door lock position switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 - 6
    Set
    Below 1 Ω
    5 - 6
    Unset
    10 kΩ or higher



NG
REPLACE FRONT DOOR LOCK ASSEMBLY
OK


8. CHECK HARNESS AND CONNECTOR (DOUBLE DOOR LOCK ECU - FRONT DOOR LOCK ASSEMBLY)
B127314E06
  1. Disconnect the D69 double lock ECU connector.

  1. Disconnect the G5 door lock connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D69-3 (ACTS) - G5-2 (DL)
    Below 1 Ω
    D69-4 (ACTR) - G5-1 (UNDL)
    Below 1 Ω
    D69-6 (DLPP) - G5-6 (DLSR)
    Below 1 Ω
    G5-5 (E) - (Body ground)
    Below 1 Ω
    D69-3 (ACTS) or G5-2 (DL) - Body ground
    10 kΩ or higher
    D69-4 (ACTR) or G5-1 (UNDL) - Body ground
    10 kΩ or higher
    D69-6 (DLPP) or G5-6 (DLSR) - Body ground
    10 kΩ or higher

  1. Reconnect the double lock ECU connector.

  1. Reconnect the door lock connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DOUBLE DOOR LOCK ECU

9. INSPECT REAR DOOR LOCK ASSEMBLY LH (DOUBLE DOOR LOCK MOTOR)

  1. B079079E01
    Check the operation of the double lock motor.
    1. Apply the battery voltage to the door lock and set the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1
      Lock
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 2
      Unlock

    2. Apply the battery voltage to the door lock motor and check the operation of the double door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 3
      Set
      Battery positive (+) → Terminal 3
      Battery negative (-) → Terminal 4
      Unset

    3. While the double locking system is set, check that the doors cannot be unlocked by operating the control cable.



NG
REPLACE REAR DOOR LOCK ASSEMBLY LH
OK


10. INSPECT REAR DOOR LOCK ASSEMBLY LH (DOUBLE DOOR LOCK POSITION SWITCH)
B079079E01
  1. Measure the resistance of the double door lock position switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    9 - 10
    Set
    Below 1 Ω
    9 - 10
    Unset
    10 kΩ or higher



NG
REPLACE REAR DOOR LOCK ASSEMBLY LH
OK


11. CHECK HARNESS AND CONNECTOR (DOUBLE DOOR LOCK ECU - REAR DOOR LOCK ASSEMBLY LH)
B127314E07
  1. Disconnect the D69 double lock ECU connector.

  1. Disconnect the I3 door lock connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D69-3 (ACTS) - I3-4 (DL)
    Below 1 Ω
    D69-4 (ACTR) - I3-3 (UNDL)
    Below 1 Ω
    D69-12 (DLPL) - I3-9 (DLSR)
    Below 1 Ω
    I3-10 (E) - Body ground
    Below 1 Ω
    D69-3 (ACTS) or I3-4 (DL) - Body ground
    10 kΩ or higher
    D69-4 (ACTR) or I3-3 (UNDL) - Body ground
    10 kΩ or higher
    D69-12 (DLPL) or I3-9 (DLSR) - Body ground
    10 kΩ or higher

  1. Reconnect the double lock ECU connector.

  1. Reconnect the door lock connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DOUBLE DOOR LOCK ECU

12. INSPECT REAR DOOR LOCK ASSEMBLY RH (DOUBLE DOOR LOCK MOTOR)

  1. B079080E01
    Check the operation of the double lock motor.
    1. Apply the battery voltage to the door lock and set the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 3
      Lock
      Battery positive (+) → Terminal 3
      Battery negative (-) → Terminal 4
      Unlock

    2. Apply the battery voltage to the door lock motor and check the operation of the double door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1
      Set
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 2
      Unset

    3. While the double locking system is set, check that the doors cannot be unlocked by operating the control cable.



NG
REPLACE REAR DOOR LOCK ASSEMBLY RH
OK


13. INSPECT REAR DOOR LOCK ASSEMBLY RH (DOUBLE DOOR LOCK POSITION SWITCH)
B079080E01
  1. Measure the resistance of the double door lock position switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 - 6
    Set
    Below 1 Ω
    5 - 6
    Unset
    10 kΩ or higher



NG
REPLACE REAR DOOR LOCK ASSEMBLY RH
OK


14. CHECK HARNESS AND CONNECTOR (DOUBLE DOOR LOCK ECU - REAR DOOR LOCK ASSEMBLY RH)
B127314E08
  1. Disconnect the D69 double lock ECU connector.

  1. Disconnect the H3 door lock connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D69-3 (ACTS) - H3-2 (DL)
    Below 1 Ω
    D69-4 (ACTR) - H3-1 (UNDL)
    Below 1 Ω
    D69-11 (DLPR) - H3-5 (DLSR)
    Below 1 Ω
    H3-6 (E) - Body ground
    Below 1 Ω
    D69-3 (ACTS) or H3-2 (DL) - Body ground
    10 kΩ or higher
    D69-4 (ACTR) or H3-1 (UNDL) - Body ground
    10 kΩ or higher
    D69-11 (DLPR) or H3-5 (DLSR) - Body ground
    10 kΩ or higher

  1. Reconnect the double lock ECU connector.

  1. Reconnect the door lock connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DOUBLE DOOR LOCK ECU


← Key Lock-in Prevention Function does not Work Properly (from Aug 2005)PRECAUTION (from Aug 2005) →