2005-2008 Yaris · Service Manual BODY ELECTRICAL

Key Lock-in Prevention Function does not Work Properly

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

When the key is in the ignition key cylinder or the door courtesy light ON signal is output to the main body ECU, performing the door lock operation with the lock switch does not lock the doors.

HINT:
Since the key reminder warning system has functions that use CAN communication, firstly confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with How to Proceed with Troubleshooting. Then, conduct the following troubleshooting procedure.


WIRING DIAGRAM

B117142E07

INSPECTION PROCEDURE


1. READ VALUE OF INTELLIGENT TESTER (D DOR CTY SW)
  1. Use the DATA LIST to check the operation of the driver side front door courtesy light switch.

    Main Body ECU:
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    D Dor Cty SW
    Driver side door courtesy switch signal / ON or OFF
    ON: Driver side door is open
    OFF: Driver side door is closed
    -

    OK:
    The display is as specified in the normal condition.



NG
Go to step 5
OK


2. READ VALUE OF INTELLIGENT TESTER (KEY UNLK WRN SW)
  1. Use the DATA LIST to check the operation of the door unlock warning switch.

    Main Body ECU:
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    Key Unlk Wrn SW
    Unlock warning switch signal / ON or OFF
    ON: Key is in ignition key cylinder
    OFF: No key is in ignition key cylinder
    -

    OK:
    The display is as specified in the normal condition.



NG
REPLACE COMBINATION METER ASSEMBLY
OK


3. INSPECT UNLOCK WARNING SWITCH ASSEMBLY

  1. B117144E02
    Remove the unlock warning switch assembly.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Not pushed
    10 kΩor higher
    1 - 2
    Pushed
    Below 1 Ω

  1. Reinstall the unlock warning switch assembly.



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY
OK


4. CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU)

  1. B121085E01
    Disconnect the D19 unlock warning switch connector.

  1. Disconnect the 4D main body ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D19-1 - 4D-7 (KSW)
    Below 1 Ω
    D19-1 or 4D-7 (KSW) - Body ground
    10 kΩor higher
    D19-2 - Body ground
    Below 1 Ω

  1. Reconnect the unlock warning switch connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

5. INSPECT FRONT DOOR COURTESY ASSEMBLY (DRIVER SIDE)

  1. B129185E01
    Remove the door courtesy switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - Body ground
    Not pushed (ON)
    Below 1 Ω
    1 - Body ground
    Pushed (OFF)
    10 kΩor higher

  1. Reinstall the door courtesy switch.



NG
REPLACE FRONT DOOR COURTESY ASSEMBLY (DRIVER SIDE)
OK


6. CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH - MAIN BODY ECU)

  1. B112021E12
    LHD:
    1. Disconnect the J2 door courtesy switch connector.

    2. Disconnect the 4A main body ECU connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      J2-1 - 4A-21 (DCTY)
      Below 1 Ω
      J2-1 or 4A-21 (DCTY) - Body ground
      10 kΩ or higher

    4. Reconnect the switch connector.

    5. Reconnect the main body ECU connector.

  1. RHD:

    1. Disconnect the J1 switch connector.

    2. Disconnect the 4A main body ECU connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      J1-1 - 4A-21 (DCTY)
      Below 1 Ω
      J1-1 or 4A-21 (DCTY) - Body ground
      10 kΩ or higher

    4. Reconnect the switch connector.

    5. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← Only Back Door LOCK / UNLOCK Functions do not Operate (from Aug 2005)Double Lock Function does not Operate Properly (from Aug 2005) →