2005-2008 Yaris · Service Manual BODY

Driver Side Power Window does not Operate with Power Window Master Switch

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

If the manual UP / DOWN and AUTO DOWN functions do not operate, a malfunction may exist in the power window regulator master switch, power window regulator motor or wire harness.

WIRING DIAGRAM

B116304E01

INSPECTION PROCEDURE


1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER SIDE)
B086401E01
  1. Remove the power window regulator motor.

  1. Apply the battery voltage to connector terminals 1 and 2.

    NOTICE:
    Do not apply the battery voltage to any terminals except terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates counterclockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates clockwise

    1. Reinstall the power window regulator motor.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER SIDE)
OK


2. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (DRIVER SWITCH)

  1. w/o rear power window:Inspect the driver switch.

    1. B118051E03
      Remove the power window regulator master switch.

    2. B118052E03
      Measure the resistance of the switch when the switch is operated.

      Standard resistance:
      LHD 
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      Always
      (ON / OFF)
      UP
      7 (E) - 12 (D)
      10 (U) - 15(B)
      Below 1 Ω
      Always
      (ON / OFF)
      OFF
      7 (E) - 10 (U)
      7 (E) - 12(D)
      Below 1 Ω
      Always
      (ON / OFF)
      DOWN
      7 (E) - 10 (U)
      12 (D) - 15(B)
      Below 1 Ω
      Always
      (ON / OFF)
      AUTO DOWN
      7 (E) - 10 (U)
      12 (D) - 15 (B)
      Below 1 Ω
      RHD 
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      Always
      (ON / OFF)
      UP
      7 (E) - 16 (D)
      18 (U) - 15(B)
      Below 1 Ω
      Always
      (ON / OFF)
      OFF
      7 (E) - 18 (U)
      7 (E) - 16(D)
      Below 1 Ω
      Always
      (ON / OFF)
      DOWN
      7 (E) - 18 (U)
      16 (D) - 15(B)
      Below 1 Ω
      Always
      (ON / OFF)
      AUTO DOWN
      7 (E) - 18 (U)
      16 (D) - 15 (B)
      Below 1 Ω

    3. Reinstall the power window regulator master switch.

  1. w/ rear power window:Inspect the driver switch.

    1. B107909E02
      Remove the power window regulator master switch.

    2. B107910E02
      Measure the resistance of the switch when the switch is operated.

      Standard resistance:
      LHD 
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      Always
      (ON / OFF)
      UP
      3 (U) - 6 (B)
      1 (E) - 4 (D)
      Below 1 Ω
      Always
      (ON / OFF)
      OFF
      1 (E) - 4 (D)
      1 (E) - 3(U)
      Below 1 Ω
      Always
      (ON / OFF)
      DOWN
      4 (D) - 6 (B)
      1 (E) - 3 (U)
      Below 1 Ω
      Always
      (ON / OFF)
      AUTO DOWN
      1 (E) - 3 (U)
      4 (D) - 6 (B)
      Below 1 Ω
      RHD 
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      Always
      (ON / OFF)
      UP
      4 (U) - 6 (B)
      9 (E) - 3 (D)
      Below 1 Ω
      Always
      (ON / OFF)
      OFF
      9 (E) - 4 (U)
      9 (E) - 3 (D)
      Below 1 Ω
      Always
      (ON / OFF)
      DOWN
      3 (D) - 6 (B)
      9 (E) - 4 (U)
      Below 1 Ω
      Always
      (ON / OFF)
      AUTO DOWN
      9 (E) - 4 (U)
      3 (D) - 6 (B)
      Below 1 Ω

    3. Reinstall the power window regulator master switch.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK


3. CHECK HARNESS AND CONNECTOR (MASTER SWITCH - MOTOR (DRIVER SIDE))
B116226E03
  1. Disconnect the G1 or F7 power window regulator master switch connector.

  1. Disconnect the G4 or F4 power window regulator motor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    w/o rear power window
    LHD 
    Tester Connection
    Specified Condition
    G1-12 (D) - G4-1
    Below 1 Ω
    G1-10 (U) - G4-2
    Below 1 Ω
    G1-12 (D) or G4-1 - Body ground
    10 kΩ or higher
    G1-10 (U) or G4-2 - Body ground
    10 kΩ or higher
    RHD 
    Tester Connection
    Specified Condition
    F7-16 (D) - F4-1
    Below 1 Ω
    F7-18 (U) - F4-2
    Below 1 Ω
    F7-16 (D) or F4-1 - Body ground
    10 kΩ or higher
    F7-18 (U) or F4-2 - Body ground
    10 kΩ or higher
    w/ rear power window
    LHD 
    Tester Connection
    Specified Condition
    G1-4 (D) - G4-1
    Below 1 Ω
    G1-3 (U) - G4-2
    Below 1 Ω
    G1-4 (D) or G4-1 - Body ground
    10 kΩ or higher
    G1-3 (U) or G4-2 - Body ground
    10 kΩ or higher
    RHD 
    Tester Connection
    Specified Condition
    F7-3 (D) - F4-1
    Below 1 Ω
    F7-4 (U) - F4-2
    Below 1 Ω
    F7-3 (D) or F4-1 - Body ground
    10 kΩ or higher
    F7-4 (U) or F4-2 - Body ground
    10 kΩ or higher

  1. Reconnect the power window regulator master switch connector.

  1. Reconnect the power window regulator motor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO POWER WINDOWS DO NOT OPERATE AT ALL


← Remote Up / Down Function does not Operate (from Aug 2005)Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch (from Aug 2005) →