Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch
Circuit diagnosis · Vehicles built from Aug 2005
DESCRIPTION
If the passenger side manual UP / DOWN function does not operate, a malfunction may exist in the power window regulator motor, power window regulator switch, power window regulator master switch or wire harness.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER SIDE) (POWER SOURCE) |
Disconnect the F1 or G7 power window regulator switch connector.

Measure the voltage of the wire harness side connector.
- Standard voltage:
LHD Tester Connection
Condition
Specified Condition
F1-3 - Body ground
Ignition switch ON
10 to 14 V
RHD Tester Connection
Condition
Specified Condition
G7-3 - Body ground
Ignition switch ON
10 to 14 V
Reconnect the power window regulator switch connector.
|
|
||||
| OK | |
| 2. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER SIDE) |
Remove the power window regulator switch.

Measure the resistance of the switch when the switch is operated.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
3 - 4
2 - 1
UP
Below 1 Ω
5 - 4
2 - 1
OFF
Below 1 Ω
5 - 4
3 - 1
DOWN
Below 1 Ω
Reinstall the power window regulator switch.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (SWITCH (PASSENGER SIDE) - MOTOR (PASSENGER SIDE)) |
Disconnect the F1 or G7 power window regulator switch connector.


Disconnect the F4 or G4 power window regulator motor connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
LHD Tester Connection
Specified Condition
F1-1 - F4-1
Below 1 Ω
F1-4 - F4-2
Below 1 Ω
F1-1 or F4-1 - Body ground
10 kΩ or higher
F1-4 or F4-2 - Body ground
10 kΩ or higher
RHD Tester Connection
Specified Condition
G7-1 - G4-1
Below 1 Ω
G7-4 - G4-2
Below 1 Ω
G7-1 or G4-1 - Body ground
10 kΩ or higher
G7-4 or G4-2 - Body ground
10 kΩ or higher
Reconnect the power window regulator switch connector.
Reconnect the power window regulator motor connector.
|
|
||||
| OK | |
| 4. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (PASSENGER SIDE) |
Remove the power window regulator motor.

Apply the battery voltage to connector terminals 1 and 2.
- NOTICE:
- Do not apply the battery voltage to any terminals except terminals 1 and 2.
Check that the motor gear rotates smoothly as follows.
- OK:
Measurement Condition
Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates clockwise
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates counterclockwise
Reinstall the power window regulator motor.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (MASTER SWITCH - SWITCH (PASSENGER SIDE)) |
Disconnect the G1 or F7 power window regulator master switch connector.


Disconnect the F1 or G7 power window regulator switch connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
- w/o rear power window
LHD Tester Connection
Specified Condition
G1-16 (U) - F1-5
Below 1 Ω
G1-18 (D) - F1-2
Below 1 Ω
G1-16 (U) or F1-5 - Body ground
10 kΩ or higher
G1-18 (D) or F1-2 - Body ground
10 kΩ or higher
RHD Tester Connection
Specified Condition
F7-12 (U) - G7-5
Below 1 Ω
F7-10 (D) - G7-2
Below 1 Ω
F7-12 (U) or G7-5 - Body ground
10 kΩ or higher
F7-10 (D) or G7-2 - Body ground
10 kΩ or higher
- w/ rear power window
LHD Tester Connection
Specified Condition
G1-16 (U) - F1-5
Below 1 Ω
G1-15 (D) - F1-2
Below 1 Ω
G1-16 (U) or F1-5 - Body ground
10 kΩ or higher
G1-15 (D) or F1-2 - Body ground
10 kΩ or higher
RHD Tester Connection
Specified Condition
F7-12 (U) - G7-5
Below 1 Ω
F7-13 (D) - G7-2
Below 1 Ω
F7-12 (U) or G7-5 - Body ground
10 kΩ or higher
F7-13 (D) or G7-2 - Body ground
10 kΩ or higher
Reconnect the switch connectors.
Reconnect the power window regulator motor connector.
|
|
||||
| OK | |
| 6. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (PASSENGER SWITCH) |
w/o rear power window:Inspect the passenger switch.
Remove the power window regulator master switch.

Measure the resistance of the switch when the switch is operated.

- Standard resistance:
LHD Window Lock Switch Condition
Power Window Switch Condition
Tester Connection
Specified Condition
OFF
UP
7 (E) - 18 (D)
16 (U) - 15 (B)
Below 1 Ω
OFF
OFF
7 (E) - 16 (U)
7 (E) - 18 (D)
Below 1 Ω
OFF
DOWN
7 (E) - 16 (U)
15 (B) - 18 (D)
Below 1 Ω
ON
UP
7 (E) - 18 (D)
10 kΩ or higher
16 (U) - 15 (B)
Below 1 Ω
ON
OFF
16 (U) - 18 (D)
Below 1 Ω
ON
DOWN
7 (E) - 16 (U)
10 kΩ or higher
15 (B) - 18 (D)
Below 1 Ω
RHD Window Lock Switch Condition
Power Window Switch Condition
Tester Connection
Specified Condition
OFF
UP
7 (E) - 10 (D)
12 (U) - 15 (B)
Below 1 Ω
OFF
OFF
7 (E) - 12 (U)
7 (E) - 10 (D)
Below 1 Ω
OFF
DOWN
7 (E) - 12 (U)
15 (B) - 10 (D)
Below 1 Ω
ON
UP
7 (E) - 10 (D)
10 kΩ or higher
12 (U) - 15 (B)
Below 1 Ω
ON
OFF
12 (U) - 10 (D)
Below 1 Ω
ON
DOWN
7 (E) - 12 (U)
10 kΩ or higher
15 (B) - 10 (D)
Below 1 Ω
Reinstall the power window regulator master switch.
w/ rear power window:Inspect the passenger switch.
Remove the power window regulator master switch.

Measure the resistance of the switch when the switch is operated.

- Standard resistance:
LHD Window Lock Switch Condition
Power Window Switch Condition
Tester Connection
Specified Condition
OFF
UP
1 (E) - 15 (D)
6 (B) - 16 (U)
Below 1 Ω
OFF
OFF
1 (E) - 16 (U)
1 (E) - 15 (D)
Below 1 Ω
OFF
DOWN
1 (E) - 16 (U)
6 (B) - 15 (D)
Below 1 Ω
ON
UP
1 (E) - 15 (D)
10 kΩ or higher
6 (B) - 16 (U)
Below 1 Ω
ON
OFF
15 (D) - 16 (U)
Below 1 Ω
ON
DOWN
1 (E) - 15 (D)
10 kΩ or higher
6 (B) - 15 (D)
Below 1 Ω
RHD Window Lock Switch Condition
Power Window Switch Condition
Tester Connection
Specified Condition
OFF
UP
9 (E) - 13 (D)
6 (B) - 12 (U)
Below 1 Ω
OFF
OFF
9 (E) - 12 (U)
9 (E) - 13 (D)
Below 1 Ω
OFF
DOWN
9 (E) - 12 (U)
6 (B) - 13 (D)
Below 1 Ω
ON
UP
9 (E) - 13 (D)
10 kΩ or higher
6 (B) - 12 (U)
Below 1 Ω
ON
OFF
13 (D) - 12 (U)
Below 1 Ω
ON
DOWN
9 (E) - 12 (U)
10 kΩ or higher
6 (B) - 13 (D)
Below 1 Ω
Reinstall the power window regulator master switch.
|
|
||||
| OK | ||
| ||
