2005-2008 Yaris · Service Manual SECURITIES

TERMINALS OF ECU

System information · Vehicles built from Aug 2005


CHECK TRANSPONDER KEY AMPLIFIER
B065593E10
  1. Disconnect the D24 amplifier connector.

  2. Measure the resistance of the wire harness side connector.

    Standard resistance: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    AGND (D24-7) - Body ground
    GR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the D24 amplifier connector.

  4. Measure the resistance and voltage of the connector.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    VC5 (D24-1) - AGND (D24-7)
    P- GR
    Power source
    1: No key in ignition key cylinder →
    2: Key inserted
    1: 0 V →
    2: 4.6 to 5.4 V
    CODE(D24-4) - AGND (D24-7)
    G- GR
    Demodulated signal of key code data
    No key in ignition key cylinder →
    Key inserted
    Pulse generation
    (see waveform 1)
    TXCT (D24-5) - AGND (D24-7)
    V- GR
    Key code output signal
    No key in ignition key cylinder →
    Key inserted
    Pulse generation
    (see waveform 2)
    AGND (D24-7) - Body ground
    GR- Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the amplifier.

  5. Inspect using an oscilloscope.

    1. B069240E03
      Waveform 1
      Terminal
      CODE - AGND
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      No key in ignition key cylinder →
      Key inserted

    2. B069239E03
      Waveform 2
      Terminal
      TXCT - AGND
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      No key in ignition key cylinder →
      Key inserted


CHECK TRANSPONDER KEY ECU ASSEMBLY
B085907E05
  1. Disconnect the D23 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (D23-16) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    AGND (D23-5) - Body ground
    GR - Body ground
    Ground for transponder key amplifier
    Always
    Below 1 Ω
    EGND* (D23-11) - Body ground
    BR* - Body ground
    Ground for ECM
    Always
    Below 1 Ω
    +B (D23-1) - GND (D23-16)
    L - W-B
    Battery
    Always
    11 to 14 V
    IG (D23-2) - AGND (D23-5)
    R - GR
    Ignition switch
    Ignition switch
    1: OFF →
    2: ON
    1: 0 V →
    2: 11 to 14 V
    *: For 1NZ-FE, 2NZ-FE, 2SZ-FE and 2ZR-FE engine
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D23 ECU connector.

  4. Measure the voltage of the connector.

    Standard voltage: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    KSW (D23-3) - GND (D23-16)
    O - W-B
    Unlock warning switch
    1: No key in ignition key cylinder →
    2: Key inserted
    1: 11 to 14 V→
    2: Below 1 V
    VC5 (D23-14) - AGND (D23-5)
    P - GR
    Power source
    1: No key in ignition key cylinder →
    2: Key inserted
    1: 0 V →
    2: 4.6 to 5.4 V
    TXCT (D23-4) - AGND (D23-5)
    V - GR
    Transponder key amplifier communication signal
    No key in ignition key cylinder →
    Key inserted
    Pulse generation
    (see waveform 1)
    CODE (D23-15) - AGND (D23-5)
    G - GR
    Transponder key amplifier communication signal
    No key in ignition key cylinder →
    Key inserted
    Pulse generation
    (see waveform 2)
    EFIO (D23-13) - GND (D23-16)
    W - W-B
    ECM output signal
    Ignition switch
    1: OFF →
    2: ON
    Pulse generation
    (see waveform 3)
    EFII (D23-12) - GND (D23-16)
    O - W-B
    ECM input signal
    Ignition switch
    1: OFF →
    2: ON
    Pulse generation
    (see waveform 4)
    CTY (D23-7) - GND (D23-16)
    B - W-B
    Courtesy signal
    1: Driver side door open →
    2: closed
    1: 11 to 14 V →
    2: Below 1 V
    IND (D23-8)*- GND (D23-16)
    LG* - W-B
    Security indicator signal
    Engine immobiliser system
    SET → UNSET
    1: 3 to 5 V →
    2: Below 1 V
    D (D23-9) - GND (D23-16)
    W - W-B
    Diagnosis tester communication
    Ignition switch ON
    Pulse generation
    *: Except Europe.
    If the result is not as specified, there may be a malfunction in the ECU.

  5. Inspect using an oscilloscope.

    1. B069239E04
      Waveform 1
      Terminal
      TXCT - AGND
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      Ignition switch
      1: OFF →
      2: ON

    2. B069240E03
      Waveform 2
      Terminal
      CODE - AGND
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      Ignition switch
      1: OFF →
      2: ON

    3. B069241E01
      Waveform 3
      Terminal
      EFIO - GND
      Tool Setting
      10 V/DIV., 500 ms/DIV.
      Condition
      Ignition switch
      OFF → ON

    4. B069242E02
      Waveform 4
      Terminal
      EFII - GND
      Tool Setting
      10 V/DIV., 500 ms/DIV.
      Condition
      Ignition switch
      OFF → ON


CHECK ECM

  1. 1KR-FE:
    A116116E03

    1. Disconnect the A32 ECM connector.

    2. Measure the voltage :of the wire harness side connectors.

      Standard: 
      Symbols (Terminal No.)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      IMI (A32-31) - E1 (A32-1)
      W - W-B
      Transponder key ECU input signal
      Ignition switch
      OFF → ON
      Pulse generation
      (see waveform 1)
      IMO (A32-40) - E1 (A32-1)
      O - W-B
      Transponder key ECU output signal
      Ignition switch
      OFF → ON
      Pulse generation
      (see waveform 2)
      If the result is not as specified, there may be a malfunction on the wire harness side.

  2. 1NZ-FE, 2NZ-FE, 2SZ-FE and 2ZR-FE:
    B116297E10

    1. Disconnect the A21 ECM connector.

    2. Measure the voltage and resistance of the wire harness side connectors.

      Standard voltage: 
      Symbols (Terminal No.)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      IMI (A21-11) - EOM (A21-9)
      W - BR
      Transponder key ECU input signal
      Ignition switch
      OFF → ON
      Pulse generation
      (see waveform 1)
      IMO (A21-10) - EOM (A21-9)
      O - BR
      Transponder key ECU output signal
      Ignition switch
      OFF → ON
      Pulse generation
      (see waveform 2)
      EOM (A21-9) - Body ground
      BR - Body ground
      Ground
      Always
      Below 1 Ω
      If the result is not as specified, there may be a malfunction in the wire harness.

  3. 1ND-TV:
    A115971E02

    1. Disconnect the A49 ECM connector.

    2. Measure the voltage of the wire harness side connectors.

      Standard: 
      Symbols (Terminal No.)
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      IMI (A49-6) - E1 (A49-2)
      W - W-B
      Transponder key ECU input signal
      Ignition switch
      OFF → ON
      Pulse generation
      (see waveform 1)
      IMO (A49-4) - E1 (A49-2)
      O - W-B
      Transponder key ECU output signal
      Ignition switch
      OFF → ON
      Pulse generation
      (see waveform 2)
      If the result is not as specified, there may be a malfunction in the wire harness.

  4. Inspect using an oscilloscope.

    1. B069241E01
      Waveform 1
      Terminal
      IMI - E1*1
      IMI - EOM*2
      Tool Setting
      10 V/DIV., 500 ms/DIV.
      Condition
      Ignition switch
      OFF → ON
      *1: For 1KR-FE and 1ND-TV engine.
      *2: For 1NZ-FE, 2NZ-FE, 2SZ-FE and 2ZR-FE engine.

    2. B069242E02
      Waveform 2
      Terminal
      IMO - E1*1
      IMO - EOM*2
      Tool Setting
      10 V/DIV., 500 ms/DIV.
      Condition
      Ignition switch
      OFF → ON
      *1: For 1KR-FE and 1ND-TV engine.
      *2: For 1NZ-FE, 2NZ-FE, 2SZ-FE and 2ZR-FE engine.

← PROBLEM SYMPTOMS TABLE (from Nov 2006)DIAGNOSIS SYSTEM (from Aug 2005) →