2005-2008 Yaris · Service Manual SECURITIES

B2796 No Communication in Immobiliser System

Diagnostic trouble codes · Vehicles built from Aug 2005

Also covers:

DESCRIPTION

This DTC is output when a key without a transponder chip is inserted into the ignition key cylinder or if communication between the key and transponder key ECU is impossible.
DTC No.
DTC Detection Condition
Trouble Area
B2796
No communication
  1. Key
  2. Wire harness
  3. Transponder key amplifier
  4. Transponder key ECU assembly
B2798
Communication error
Key

WIRING DIAGRAM

B111588E06

INSPECTION PROCEDURE


1. READ VALUE OF INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON with the key that cannot start the engine.

  1. On the intelligent tester, enter the following menus: Body/Immobiliser/Data List/Immobiliser. Read the values.

    Transponder key ECU assembly 
    Item
    Measurement Item/
    Display (Range)
    Normal Condition
    Diagnostic Note
    Immobiliser
    Immobiliser system status/
    SET or UNSET
    UNSET: Ignition switch ON
    SET: Without key
    -

    OK:
    "UNSET" (ignition switch ON) appears on the screen.



NG
Go to step 2
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

2. CHECK WHETHER ENGINE STARTS WITH OTHER KEYS
  1. Check whether the engine starts with the vehicles other keys.

    OK:
    Engine starts.



NG
Go to step 3
OK

RE-REGISTER OR REPLACE KEY THAT CANNOT START ENGINE

3. READ VALUE OF INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON with the key that will not start the engine.

  1. On the intelligent tester, enter the following menus: Body/Immobiliser/Data List/Antenna Coil Status. Read the result.

    Transponder key ECU assembly 
    Item
    Measurement Item/
    Display (Range)
    Normal Condition
    Diagnostic Note
    Antenna Coil Status
    Antenna coil condition/
    NORMAL or FAIL
    NORMAL: Antenna coil is normal
    FAIL: Antenna coil is malfunctioning
    -

    OK:
    "NORMAL" (antenna coil is normal) appears on the screen.



NG
REPLACE TRANSPONDER KEY AMPLIFIER
OK


4. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - TRANSPONDER KEY AMPLIFIER)

  1. B110403E04
    Disconnect the D23 transponder key ECU connector.

  1. Disconnect the D24 transponder key amplifier connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D23-14 (VC5) - D24-1 (VC5)
    Below 1 Ω
    D23-15 (CODE) - D24-4 (CODE)
    Below 1 Ω
    D23-4 (TXCT) - D24-5 (TXCT)
    Below 1 Ω
    D23-5 (AGND) - D24-7 (AGND)
    Below 1 Ω
    D23-14 (VC5) or D24-1 (VC5) -
    Body ground
    10 kΩ or higher
    D23-15 (CODE) or D24-4 (CODE) -
    Body ground
    10 kΩ or higher
    D23-4 (TXCT) or D24-5 (TXCT) -
    Body ground
    10 kΩ or higher
    D23-5 (AGND) or D24-7 (AGND) -
    Body ground
    10 kΩ or higher

  1. Disconnect the transponder key ECU and transponder key amplifier connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE TRANSPONDER KEY AMPLIFIER
  1. After replacing the transponder key amplifier with a normally functioning amplifier, check that the engine starts.

    OK:
    Engine starts.



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK

NORMAL (TRANSPONDER KEY AMPLIFIER DEFECT)


← B2795 Unmatched Key Code (from Aug 2005)B2797 Communication Malfunction No. 1 (from Aug 2005) →