TERMINALS OF ECU
System information · Vehicles built from Nov 2006
| CHECK THEFT WARNING ECU ASSEMBLY (THEFT DETERRENT ECU) |
Disconnect the D86 ECU connector.


Check the voltage or resistance of each terminal of the wire harness side connector.
If the result is not as specified, there may be a malfunction on the wire harness side.Standard: Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
+B1 (D86-11) - Body ground
B - Body ground
Battery
Always
11 to 14 V
+B2 (D86-13) - Body ground
L - Body ground
Battery
Always
11 to 14 V
IG (D86-9) - E (D86-16)
GR - W-B
Engine switch signal
Engine switch OFF → ON
Below 1 V → 11 to 14 V
E (D86-16) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
Reconnect the D86 ECU connector.
Check the voltages of each terminal of the connector.
If the result is not as specified, the theft warning ECU assembly may be malfunctioning.Standard voltage: Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
BRK+ (D86-24) - Body ground
P - Body ground
Alarm BERKES Communication
Theft deterrent system is in alarm sounding state.
Pulse generation
(1.5 V ← → Below 1.2 V)
BRK- (D86-25) - Body ground
O - Body ground
Alarm BERKES Communication
Lock all doors by wireless operation (Theft deterrent system is in arming preparation state).
Pulse generation
(1.5 V ← → Below 1.2 V)
SH- (D86-15) - Body ground
O - Body ground
Security horn
Security horn is sounding (Theft deterrent system is in alarm sounding state).
Pulse generation
(11 to 14 V ← → Below 1 V)
+B1 (D86-11) - E (D86-16)
B - W-B
+B power supply
Always
11 to 14 V
IND (D86-29) - E (D86-16)
LG - W-B
Security indicator
Security indicator lights up (illuminates for 30 seconds in alarm sounding state. It flashes when immobiliser system is operating).
5 V or more
DSWH (D86-4) - E (D86-16)
W - W-B
Engine hood courtesy switch input
Engine hood courtesy switch OFF (Closed) → ON (Open)
11 to 14 V → Below 1 V
| CHECK THEFT WARNING ECU ASSEMBLY (THEFT DETERRENT ECU) |
Disconnect the 4B and 4E main body ECU (vehicle rear side) connectors.




Measure the voltage and resistance of the wire harness side connectors.
If the result is not as specified, there may be a malfunction in the wire harness.Standard: Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
BECU (4B-30) - GND1 (4E-17)
L - W-B
Battery (power supply)
Always
11 to 14 V
GND1 (4E-17) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
Reconnect the main body ECU (vehicle rear side) connectors.
Measure the voltage of the wire harness side connectors.
If the result is not as specified, there may be a malfunction in the wire harness.Standard voltage: Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
DCTY (4A-21) - Body ground
R - Body ground
Driver side door courtesy switch input
Driver side door closed
11 to 14 V
DCTY (4A-21) - Body ground
R - Body ground
Driver side door courtesy switch input
Driver side door open
0 V
PCTY (4A-24) - Body ground
L - Body ground
Passenger side door courtesy switch input
Passenger side door closed
11 to 14 V
PCTY (4A-24) - Body ground
L - Body ground
Passenger side door courtesy switch input
Passenger side door open
0 V
RRCY (4A-20) - Body ground
L - Body ground
Rear RH door courtesy switch input
Rear RH door closed
11 to 14 V
RRCY (4A-20) - Body ground
L - Body ground
Rear RH door courtesy switch input
Rear RH door open
0 V
RRCY (4A-5) - Body ground
G - Body ground
Rear LH door courtesy switch input
Rear LH door closed
11 to 14 V
RRCY (4A-5) - Body ground
G - Body ground
Rear LH door courtesy switch input
Rear LH door open
0 V
BCTY (4A-7) - Body ground
SB- Body ground
Back door courtesy switch input
Back side door closed
11 to 14 V
BCTY (4A-7) - Body ground
SB- Body ground
Back door courtesy switch input
Back side door open
0 V
HAZ (4S-17) - Body ground
B - Body ground
Hazard warning light signal
Answer-back ON
Below 1 V
HAZ (4S-17) - Body ground
B - Body ground
Hazard warning light signal
Answer-back OFF
11 to 14 V