2005-2008 Yaris · Service Manual BODY

Key-off Operation Function Operates even if Operating Conditions are not Satisfied

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

  1. When the driver door has not been opened and fully closed, each door power window regulator can control its power window operation for approximately 45 seconds after the ignition switch is turned from on (IG) to off (the key is removed), by receiving operation permission signals from the main body ECU. However, when approximately 45 seconds have elapsed or the driver door or front passenger side door is opened within approximately 45 seconds of the ignition switch being turned off (the key is removed), the power window regulator motor stops to operating.

    NOTICE:
    1. The power window control system uses a multiplex communication system (LIN). Inspect the communication function by following HOW TO PROCEED WITH TROUBLESHOOTING. Troubleshoot the power window control system after confirming that the communication system is functioning properly.
    2. The power window control system prohibits the AUTO UP/DOWN function when the jam protection function malfunctions. Therefore, troubleshoot the power window control system after confirming that no diagnostic codes are displayed.


WIRING DIAGRAM

E124607E02

INSPECTION PROCEDURE

CAUTION:
When using the intelligent tester to troubleshoot the LIN communication line: Connect the intelligent tester to the vehicle, and turn the courtesy light switch on and off at 1.5 second intervals until communication between the tester and vehicle begins.


1. READ VALUE OF INTELLIGENT TESTER (LIN COMMUNICATION)
  1. Use the data list to check the function of the power window regulator master switch.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and turn the tester ON.

    3. Select the following menu items: Body/ Body ECU/ Data List / Comm D-Door Mtr.

    4. Read the value.

      Result:
      Item
      Measurement Item / Display (Range)
      Status
      Comm D-Door Mtr
      Connection status between power window regulator motor assembly (driver side) and main body ECU
      OK/Stop
      OK: Connection
      Stop: No connection



NG
GO TO ENGINE IMMOBILISER SYSTEM (B2785)
OK


2. CHECK OPERATION FUNCTION AFTER IGNITION SWITCH IS TURNED OFF
  1. Check the power window operation function after the ignition switch is turned off.

    Result: 
    Status
    Proceed to
    When power window can still be operated even after opening driver door and passenger door within approximately 45 seconds of ignition switch being turned off
    A
    When power window can still be operated even after approximately 45 seconds have elapsed after ignition switch turned off
    B



B
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER SIDE)
A


3. READ VALUE OF INTELLIGENT TESTER (DOOR COURTESY LIGHT SWITCH)
  1. Use the data list to check the driver side door courtesy switch signal.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and turn the tester ON.

    3. Select the following menu items: Body/ Body ECU/ Data List / D Dor Cty SW.

    4. Read the result.

      Main body ECU:
      Item
      Measurement Item/ Display (Range)
      Status
      D Dor Cty SW
      Driver side door courtesy switch signal/
      ON/OFF
      ON: Driver door open
      OFF: Driver door closed
      P Dor Cty SW
      Front passenger side courtesy switch signal/
      ON/OFF
      ON: Front passenger door open
      OFF: Front passenger door closed

OK:
OK is displayed on the intelligent tester screen.



OK
REPLACE MAIN BODY ECU
NG


4. INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (DRIVER SIDE AND PASSENGER SIDE)

  1. B058556E13
    Measure the resistance.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Switch body
    Pushed
    10 kΩ or higher
    1 - Switch body
    Not Pushed
    Below 1 Ω



NG
REPLACE DOOR COURTESY LIGHT SWITCH ASSEMBLY
OK


5. INSPECT MAIN BODY ECU

  1. B140307E01
    Measure the voltage without removing the 4A main body ECU connector.

    Standard voltage:
    for Driver side 
    Main body ECU Tester Connection
    Driver Door Condition
    Specified Condition
    4A-21 (DCTY) - Body ground
    Fully closed
    10 to 14V
    4A-21 (DCTY) - Body ground
    Open
    Below 1V
    for Passenger side 
    Main body ECU Tester Connection
    Driver Door Condition
    Specified Condition
    4A-24 (PCTY) - Body ground
    Fully closed
    10 to 14V
    4A-24 (PCTY) - Body ground
    Open
    Below 1V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch (from Aug 2005)Auto Up Operation does not Fully Close Power Window (Jam Protection Function is Activated) (from Aug 2005) →