2005-2008 Yaris · Service Manual BODY

Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

  1. When the AUTO UP/DOWN dose not function, the power window control system may be in fail-safe mode. If the system has not been initialized after replacement of the driver door power window regulator motor, it also results in the same problem.

    NOTICE:
    1. The power window control system uses a multiplex communication system (LIN). Inspect the communication function by following HOW TO PROCEED WITH TROUBLESHOOTING. Troubleshoot the power window control system after confirming that the communication system is functioning properly.
    2. When the power window regulator motor assembly (on the driver side) is reinstalled or replaced, the power window control system must be initialized.
    3. After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the AUTO UP function is used. In such cases, the AUTO UP function can be resumed by repeating the following operation at least 5 times:
      1. Close the power window by fully pulling up the power window switch and holding it in the AUTO UP position.
      2. Open the power window by fully pushing down the switch.

    HINT:
    If the pulse sensor built into the power window regulator motor assembly (on the driver side) malfunctions, the power window control system enters fail-safe mode. The remote UP/DOWN and AUTO UP/DOWN functions cannot be operated during fail-safe mode. (However, the power window can be closed by holding the power window switch at the AUTO UP position and opened manually by pushing down the switch).


WIRING DIAGRAM

B111516E01

INSPECTION PROCEDURE


1. CHECK DTC
  1. Check for DTCs.

  1. Connect an intelligent tester to the DLC3.

  1. By following the tester screen display, check whether any DTCs are output.

    Result:
    Display
    Proceed to
    No output
    A
    DTC output
    B



B
PROCEED TO INSPECTION PROCEDURE RELEVANT TO OUTPUT DTC
A


2. READ VALUE OF INTELLIGENT TESTER (MASTER SWITCH)
  1. Use the data list to check the function of the power window master switch.

    Power window regulator master switch assembly:
    Item
    Measurement Item/ Display (Range)
    Normal Condition
    Diagnostic Note
    Door P/W Auto SW
    Driver side power window AUTO switch signal/
    ON or OFF
    ON: Driver side power window AUTO switch operates
    OFF: Driver side power window AUTO switch does not operate
    -
    Door P/W Up SW
    Driver side power window UP switch signal/
    ON or OFF
    ON: Driver side power window UP switch operates
    OFF: Driver side power window UP switch does not operate
    -
    Door P/W Down SW
    Driver side power window DOWN switch signal/
    ON or OFF
    ON: Driver side power window DOWN switch operates
    OFF: Driver side power window DOWN switch does not operate
    -

    OK:
    ON (switch operates) appears on screen.



NG
Go to step 4
OK


3. CHECK HARNESS AND CONNECTOR (MASTER SWITCH - MOTOR (DRIVER SIDE))

  1. Disconnect the G1 or F7 power window regulator master switch connector.B119970E02

  1. Disconnect the G8 or F8 power window regulator motor (driver side) connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    LHD 
    Tester Connection
    Specified Condition
    G1-1 (AUTO) - G8-4 (AUTO)
    Below 1 Ω
    RHD 
    Tester Connection
    Specified Condition
    F7-18 (AUTO) - F8-4 (AUTO)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

  1. B119968E01
    Remove the power window regulator master switch.

  1. Measure the resistance.

    Standard resistance:
    LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    18 (U) - 7 (E) - 1 (AUTO)
    AUTO UP
    Below 1 Ω
    10 (D) - 15 (B)
    AUTO UP
    Below 1 Ω
    18 (U) - 7 (E)
    UP
    Below 1 Ω
    10 (D) - 15 (B)
    UP
    Below 1 Ω
    18 (U) - 10 (D) - 15 (B)
    OFF
    Below 1 Ω
    10 (D) - 7 (E)
    DOWN
    Below 1 Ω
    18 (U) - 15 (B)
    DOWN
    Below 1 Ω
    1 (AUTO) - 10 (D) - 7 (E)
    AUTO DOWN
    Below 1 Ω
    18 (U) - 15 (B)
    AUTO DOWN
    Below 1 Ω
    RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    9 (U) - 7 (E) - 18 (AUTO)
    AUTO UP
    Below 1 Ω
    6 (D) - 15 (B)
    AUTO UP
    Below 1 Ω
    9 (U) - 7 (E)
    UP
    Below 1 Ω
    6 (D) - 15 (B)
    UP
    Below 1 Ω
    9 (U) - 6 (D) - 15 (B)
    OFF
    Below 1 Ω
    6 (D) - 7 (E)
    DOWN
    Below 1 Ω
    9 (U) - 15 (B)
    DOWN
    Below 1 Ω
    18 (AUTO) - 6 (D) - 7 (E)
    AUTO DOWN
    Below 1 Ω
    9 (U) - 15 (B)
    AUTO DOWN
    Below 1 Ω

  1. Reinstall the power window regulator master switch.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER SIDE)


← Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch (from Aug 2005)Key-off Operation Function Operates even if Operating Conditions are not Satisfied (from Aug 2005) →