TERMINALS OF ECU
System information · Vehicles built from Nov 2005
| Transmission Control ECU: |


| Symbols (Terminal No.) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
| +B - GND (D79-1 - D79-6) |
B - W-B |
Battery (ECU power source) |
Always |
10 to 14 V |
| IG - GND (D79-3 - D79-6) |
O - W-B |
Ignition switch |
Ignition switch off → on (IG) |
Below 1 V → 10 to 14 V |
| PKB - GND (D79-4 - D79-6) |
P - W-B |
Parking brake switch |
Ignition switch on (IG), Parking brake switch OFF → ON (Parking brake lever released → pulled) |
10 to 14 V → Below 1 V |
| SLS - GND (D79-5 - D79-6) |
LG - W-B |
Shift lock solenoid |
Ignition switch on (IG), Brake pedal depressed → Released |
10 to 14 V → Below 1 V |
| GND - Body ground (D79-6 - Body ground) |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
| MDSW - GND (D79-10 - D79-6) |
L - W-B |
Transmission shift main switch |
Ignition switch on (IG), Shift lever position E → M |
10 to 14 V → Below 1 V |
| LS4C - GND (D79-11 - D79-6) |
B - W-B |
Shift lever position sensor |
Ignition switch on (IG), Shift lever position N → except N |
10 to 14 V → Below 1 V |
| LS3C - GND (D79-12 - D79-6) |
W - W-B |
Shift lever position sensor |
Ignition switch on (IG), Shift lever position E or M → R or N |
10 to 14 V → Below 1 V |
| LS2C - GND (D79-13 - D79-6) |
LG - W-B |
Shift lever position sensor |
Ignition switch on (IG), Shift lever position R → Except R |
10 to 14 V → Below 1 V |
| LSW5 - GND (D79-15 - D79-6) |
R - W-B |
Shift lever position sensor |
Ignition switch on (IG), Shift lever position except [-] → [-] |
10 to 14 V → Below 1 V |
| LSW4 - GND (D79-16 - D79-6) |
G - W-B |
Shift lever position sensor |
Ignition switch on (IG), Shift lever position except N → N |
10 to 14 V → Below 1 V |
| LSW3 - GND (D79-17 - D79-6) |
B - W-B |
Shift lever position sensor |
Ignition switch on (IG), Shift lever position R or N → Except R and N |
10 to 14 V → Below 1 V |
| LSW2 - GND (D79-18 - D79-6) |
W - W-B |
Shift lever position sensor |
Ignition switch on (IG), Shift lever position except R → R |
10 to 14 V → Below 1 V |
| LSW1 - GND (D79-19 - D79-6) |
GR - W-B |
Shift lever position sensor |
Ignition switch on (IG), Shift lever position except [+] → [+] |
10 to 14 V → Below 1 V |
| PWR - GND (D79-23 - D79-6) |
GR - W-B |
Pattern select switch |
Ignition switch on (IG), Pattern select switch OFF → ON |
10 to 14 V → Below 1 V |
| SIL - GND (D79-24 - D79-6) |
L - W-B |
Terminal SIL of DLC3 |
During communication with intelligent tester or OBD scan tool |
Pulse generation |
| DG - GND (D79-25 - D79-6) |
P - W-B |
Terminal TC of DLC3 |
Ignition switch on (IG) → Connect terminals TC and CG of DLC3 |
10 to 14 V → Below 1 V |
| INDC - GND (D79-29 - D79-6) |
R - W-B |
Communication line with combination meter |
Always |
Below 1.44 V |
| INDA - GND (D79-31 - D79-6) |
Y - W-B |
Communication line with combination meter |
Ignition switch on (IG) |
Pulse generation (See waveform 1) |
| STP - GND (D79-34 - D79-6) |
G - W-B |
Stop light switch |
Brake pedal depressed → Released |
10 to 14 V → Below 1 V |
| ST1- - GND (D79-35 - D79-6) |
Y - W-B |
Stop light switch |
Ignition switch on (IG), Brake pedal released → depressed |
10 to 14 V → Below 1 V |
| CAN+ - CAN- (A38-1 - A38-2) |
W - B |
CAN communication |
Ignition switch on (IG) |
Pulse generation (See waveform 2) |
| MREL - GND (A38-5 - D79-6) |
LG - W-B |
AMT relay (motor power source) |
Ignition switch off → on (IG) |
Below 1 V → 10 to 14 V |
| STA - GND (A38-6 - D79-6) |
SB - W-B |
Starter relay operation signal (input) |
Ignition switch off, Brake pedal depressed, Shift lever position N → Starter operates |
Below 1 V → 10 to 14 V |
| RSW - GND (A38-9 - D79-6) |
R - W-B |
Back-up light switch |
Ignition switch on (IG), Shift lever position except R → R |
Below 1 V → 10 to 14 V |
| NE - GND (A38-10 - D79-6) |
L - W-B |
Engine speed signal from ECM |
Idling |
Pulse generation (See waveform 3) |
| NIP- - NIP+ (A38-15 - A38-16) |
V - P |
Transmission revolution sensor |
Engine running, Clutch engaged (during driving) |
Pulse generation (See waveform 4) |
| E2S1 - GND (A38-17 - D79-6) |
P - W-B |
Shift stroke sensor ground (main) |
Always |
Below 1Ω |
| VSS1 - GND (A38-18 - D79-6) |
B - W-B |
Shift stroke sensor voltage monitor (main) |
Ignition switch on (IG) |
0.5 V to 4.5 V |
| VCS1 - GND (A38-19 - D79-6) |
W - W-B |
Shift stroke sensor power source (main) |
ignition switch on (IG) |
4.5 V to 5.5 V |
| VCL1 - GND (A38-20 - D79-6) |
O - W-B |
Select stroke sensor power source (main) |
Ignition switch on (IG) |
4.5 V to 5.5 V |
| VSL1 - GND (A38-21 - D79-6) |
V - W-B |
Select stroke sensor voltage monitor (main) |
Ignition switch on (IG) |
0.5 V to 4.5 V |
| E2L1 - GND (A38-22 - D79-6) |
Y - W-B |
Select stroke sensor ground (main) |
Always |
Below 1 Ω |
| SPD - GND (A38-23 - D79-6) |
V - W-B |
Vehicle speed signal |
During driving |
Pulse generation (See waveform 5) |
| E2L2 - GND (A38-24 - D79-6) |
GR - W-B |
Select stroke sensor ground (sub) |
Always |
Below 1 Ω |
| E2R1 - GND (A38-25 - D79-6) |
LG - W-B |
Clutch stroke sensor ground (main) |
Always |
Below 1 Ω |
| VSR1 - GND (A38-26 - D79-6) |
B - W-B |
Clutch stroke sensor voltage monitor (main) |
Ignition switch on (IG) |
0.5 V to 4.5 V |
| VCR1 - GND (A38-27 - D79-6) |
W - W-B |
Clutch stroke sensor power source (main) |
Ignition switch on (IG) |
4.5 V to 5.5 V |
| E2S2 - GND (A38-28 - D79-6) |
GR - W-B |
Shift stroke sensor ground (sub) |
Always |
Below 1 Ω |
| VSS2 - GND (A38-29 - D79-6) |
BR - W-B |
Shift stroke sensor voltage monitor (sub) |
Ignition switch on (IG) |
0.5 V to 4.5 V |
| VCS2 - GND (A38-30 - D79-6) |
R - W-B |
Shift stroke sensor power source (sub) |
Ignition switch on (IG) |
4.5 V to 5.5 V |
| VCL2 - GND (A38-31 - D79-6) |
L - W-B |
Select stroke sensor power source (sub) |
Ignition switch on (IG) |
4.5 V to 5.5 V |
| VSL2 - GND (A38-32 - D79-6) |
LG - W-B |
Select stroke sensor voltage monitor (sub) |
Ignition switch on (IG) |
0.5 V to 4.5 V |
| E2R2 - GND (A38-33 - D79-6) |
GR - W-B |
Clutch stroke sensor ground (sub) |
Always |
Below 1 Ω |
| VSR2 - GND (A38-34 - D79-6) |
BR - W-B |
Clutch stroke sensor voltage monitor (sub) |
Ignition switch on (IG) |
0.5 V to 4.5 V |
| VCR2 - GND (A38-35 - D79-6) |
G - W-B |
Clutch stroke sensor power source (sub) |
Ignition switch on (IG) |
4.5 V to 5.5 V |
| MSF+ - GND (A37-1 - D79-6) |
B - W-B |
Shift motor |
Ignition switch off → on (IG) |
Below 1 V → Pulse generation (Click here) |
| +BM - GND (A37-2 - D79-6) |
B - W-B |
Motor power source |
Ignition switch off → on (IG) |
Below 1 V → 10 to 14 V |
| MSF- - GND (A37-3 - D79-6) |
W - W-B |
Shift motor |
Ignition switch off → on (IG) |
Below 1 V → Pulse generation (Click here) |
| MSL- - GND (A37-4 - D79-6) |
L - W-B |
Select motor |
Ignition switch off → on (IG) |
Below 1 V → Pulse generation (Click here) |
| MSL+ - GND (A37-5 - D79-6) |
B - W-B |
Select motor |
Ignition switch off → on (IG) |
Below 1 V → Pulse generation (Click here) |
| MCL- - GND (A37-6 - D79-6) |
GR - W-B |
Clutch motor |
Ignition switch off → on (IG) |
Below 1 V → Pulse generation (Click here) |
| MCL+ - GND (A37-7 - D79-6) |
G - W-B |
Clutch motor |
Ignition switch off → on (IG) |
Below 1 V → Pulse generation (Click here) |
| PGND - Body ground (A37-8 - Body ground) |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
Waveform 1:

Communication with Combination MeterTerminal
INDA - GND
Gauge set
2 V/DIV, 500 μs/DIV
Condition
Ignition switch on (IG)
Waveform 2:

CAN Communication TerminalTerminal
CAN+ - CAN-
Gauge set
1 V/DIV, 50 μs/DIV
Condition
Ignition switch on (IG)
Waveform 3:

Engine speed signal from ECMTerminal
NE - GND
Gauge set
5 V/DIV, 5 ms/DIV
Condition
Engine idling
Waveform 4:

Transmission Revolution Sensor TerminalTerminal
NIP- - NIP+
Gauge set
500 mV/DIV, 500 μs/DIV
Condition
Vehicle speed of approximately 30 km/h (19 mph)
Waveform 5:

Vehicle Speed Signal TerminalTerminal
SPD - GND
Gauge set
5 V/DIV, 20 ms/DIV
Condition
Vehicle speed of approximately 20 km/h (12 mph)
| ECM: |


| Symbols (Terminal No.) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
| CAN+ - CAN- (A49-45 - A49-64) |
W - B |
CAN Communication |
Ignition switch on (IG) |
Pulse generation (See waveform 1) |
| NEO - E1 (A49-22 - A49-2) |
L - W-B |
Crankshaft position sensor |
Engine idling |
Pulse generation (See waveform 2) |
| E1 - Body ground (A49-2 - Body ground) |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
Waveform 1:

CAN Communication TerminalTerminal
CAN+ - CAN-
Gauge set
1 V/DIV, 50 μs/DIV
Condition
Ignition switch on (IG)
Waveform 2:

Engine speed signalTerminal
NEO - E1
Gauge set
5 V/DIV, 1 ms/DIV
Condition
Engine idling