2005-2008 Yaris · Service Manual TRANSMISSION

DIAGNOSIS SYSTEM

Troubleshooting · Vehicles built from Nov 2005


DESCRIPTION
C121801E01
  1. The transmission control ECU has a self-diagnosis system. If the ECU, the multi-mode manual transmission system or any components operate incorrectly, the ECU detects the malfunction, and illuminates the multi-mode manual transmission warning light on the combination meter.
    The multi-mode manual transmission warning light is illuminated when the multi-mode manual transmission system malfunctions.

  2. C121802E01
    When troubleshooting Euro-OBD vehicles, the only difference from the usual troubleshooting procedure is that an OBD scan tool (complying with ISO 15031-4) or an intelligent tester is connected to the vehicle, and various data output from the vehicle ECU is read.
  3. Euro-OBD regulations require that the vehicle's on board computer illuminates the MIL (Malfunction Indicator Lamp) on the combination meter when the ECM (Engine Control Module) detects a malfunction in: 1) the emission control systems and components, or 2) the powertrain control components (which affect vehicle emissions), or 3) the ECM. Therefore, the transmission control ECU illuminates the MIL and multi-mode manual transmission warning light together if malfunctions related to these systems or components are detected.
  4. If the malfunction does not recur for 3 consecutive trips, the MIL goes out automatically. However, the DTCs remain recorded in the transmission control ECU memory.

  5. A107926E01
    To check DTCs, connect the OBD scan tool or intelligent tester to the DLC3 (Data Link Connector 3) on the vehicle. The OBD scan tool or intelligent tester also enables the DTCs to be erased and the freeze frame data and various forms of engine data to be checked. See the instruction manual of the OBD scan tool or intelligent tester for details.
  6. The DTCs include ISO controlled codes and manufacturer controlled codes. ISO controlled codes must be set as prescribed by the ISO, while manufacturer controlled codes can be set by the manufacturer within prescribed limits (Click here).

FREEZE FRAME DATA
  1. Freeze frame data record the vehicle conditions (engine speed, vehicle speed, transmission gear position, shift position, etc.) when malfunctions are detected. When troubleshooting, the freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, the transmission gear was in neutral or not, and other data, from the time the malfunction occurred.

DLC3 (Data Link Connector 3)

  1. H100769E16
    The ECU uses ISO 15765-4 for communication. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.
    Symbols (Terminal No.)
    Terminal Description
    Condition
    Specified Condition
    SIL (7) - SG (5)
    Bus "+" line
    During transmission
    Pulse generation
    CG (4) - Body ground
    Chassis ground
    Always
    Below 1 Ω
    SG (5) - Body ground
    Signal ground
    Always
    Below 1 Ω
    BAT (16) - Body ground
    Battery positive
    Always
    10 to 14 V
    CANH (6) - CANL (14)
    HIGH-level CAN bus line
    Ignition switch off*
    54 to 69 Ω
    CANH (6) - CG (4)
    HIGH-level CAN bus line
    Ignition switch off*
    200 Ω or higher
    CANL (14) - CG (4)
    LOW-level CAN bus line
    Ignition switch off*
    200 Ω or higher
    CANH (6) - BAT (16)
    HIGH-level CAN bus line
    Ignition switch off*
    6 kΩ or higher
    CANL (14) - BAT (16)
    LOW-level CAN bus line
    Ignition switch off*
    6 kΩ or higher

    NOTICE:
    *: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.

    If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and connector.

    HINT:
    The DLC3 is the interface prepared for reading various data from the vehicle's ECU. After connecting the cable of an intelligent tester or OBD scan tool, turn the ignition switch on (IG) and turn the tester or scan tool ON.

    If a communication failure message is displayed on the tester or scan tool screen (on the tester: no information available), a problem exists in either the vehicle or tester. In order to identify the location of the problem, connect the tester to another vehicle.
    If communication is normal: Inspect the DLC3 on the original vehicle.
    If communication is impossible: The problem is probably with the tester itself. Consult the service department listed in the instruction manual.


CHECK MULTI-MODE MANUAL TRANSMISSION WARNING LIGHT

  1. C121801E01
    Turn the ignition switch on (IG).

  2. Check that the warning light illuminates for 5 seconds. If the warning light does not illuminate, proceed to troubleshooting the multi-mode manual transmission warning light circuit (Click here).


BATTERY VOLTAGE
  1. Measure the voltage of the battery.

    Standard Voltage:
    11 to 14 V

    If the voltage is below 11 V, recharge the battery before proceeding.

  2. Inspect the battery, fuses, fusible links, wiring harness, connectors and ground.

← TERMINALS OF ECU (from Nov 2005)DTC CHECK / CLEAR (from Nov 2005) →