2005-2008 Yaris · Service Manual TRANSMISSION

DATA LIST / ACTIVE TEST

System information · Vehicles built from Nov 2005


DATA LIST

HINT:
By reading the Data List displayed on an intelligent tester, you can check values, including those of the switches, sensors, and actuators, without removing any parts. Reading the Data List as the first step of troubleshooting is one method of shortening diagnostic time.

NOTICE:
In the table below, the values listed under Normal Conditions are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect an intelligent tester to the DLC3.

  4. Turn the ignition switch on (IG) and turn the tester ON.

  5. Select the following menu items: Powertrain / Multi-Mode M/T / Data List.

  6. Check the values by referring to the table below.

    Items
    [Abbreviation]
    Measurement Items: Display
    Normal Conditions
    Diagnostic Notes
    MIL Status
    [MIL Status]
    MIL status:
    OFF or ON
    ON: MIL comes on
    -
    Calculated Engine Load
    [Calc E/G Load]
    Load calculated by ECM:
    Min.: 0 %, Max.: 100 %
    1KR-FE:
    11 to 25 %: Idling
    15 to 35 %: Running without load (2,500 rpm)
    2SZ-FE:
    12.8 to 19.2 %: Idling
    10.3 to 17.9 %: Running without load (2,500 rpm)
    -
    Engine Coolant Temperature
    [Coolant Temp]
    Coolant temperature:
    Min.: -40°C, Max.: 140°C
    1KR-FE:
    75 to 95°C (167 to 203°F):
    After engine warmed up
    2SZ-FE:
    80 to 100°C (176 to 212°F):
    After engine warmed up
    1. If value -40 °C (-40 °F): sensor circuit open
    2. If value 140 °C (284 °F): sensor circuit shorted
    Engine Run Time
    [Eng Run Time]
    Engine run time:
    Min.: 0 s, Max.: 65535 s
    Time since engine start
    -
    Engine Revolution
    [Engine Rev]
    Engine revolutions per minute:
    Min.: 0 rpm, Max.: 16,383.75 rpm
    1KR-FE:
    730 to 830 rpm: Idling
    2SZ-FE:
    600 to 700 rpm: Idling
    If NE signal circuit has a short or open circuit, back-up engine speed data from CAN communication displayed
    Vehicle Speed
    [Vehicle Spd]
    Vehicle speed:
    Min.: 0 km/h, Max.: 255 km/h
    0 km/h (0 mph): Vehicle stationary
    Approximately same value as combination meter display
    When vehicle speed signal malfunctions, speed value calculated from input revolution signal displayed
    Battery Voltage
    [Batt]
    Battery voltage:
    Min.: 0 V, Max.: 65.535 V
    10 to 15 V: Idling
    -
    Drive Mile after Malfunction
    [Driving Mileage]
    Accumulated driving mileage since malfunction detection:
    Min.: 0 km/h, Max.: 65,535 km/h
    0 km/h (0 mph): System normal
    Distance driven since occurrence of diagnosis malfunction displayed
    Running Time from MIL ON
    [MIL On Run Time]
    Running time from MIL ON:
    Min.: 0 min, Max.: 65535 min
    Equivalent to running time since MIL ON
    -
    Warmup Cycle Cleard DTC
    [Wu Cyc DTC clear]
    Warm-up cycle since DTC cleared:
    Min.: 0 , Max.: 255
    -
    Number of warm-up cycles since DTC cleared
    Distance from DTC Cleared
    [Dist DTC Clear]
    Distance since DTC cleared:
    Min.: 0 Km, Max.: 65535 Km
    Equivalent to drive distance since DTCs erased
    -
    Time after DTC Cleared
    [Time DTC Clear]
    Time since DTC cleared:
    Min.: 0 min, Max.: 65535 min
    Equivalent to time since DTCs erased
    -
    Vehicle Speed Signal
    [Vehicle Spd Sig]
    Vehicle speed signal:
    Min.: 0 km/h, Max.: 327.675 km/h
    0 km/h (0 mph): Vehicle stationary
    When vehicle speed signal malfunctions, speed value calculated from input revolution signal displayed
    Input Revolution
    [Input Rev.]
    Transmission input revolution:
    Min.: 0 rpm, Max.: 12,800 rpm
    0 rpm: Vehicle stationary
    When input revolution signal malfunctions, value calculated from vehicle speed signal displayed
    Backup Engine Speed
    [Bacup Engin Spd]
    Back-up engine speed from CAN communication:
    Min.: 0 rpm, Max.: 8,160 rpm
    Approximately same as tachometer reading: Engine running
    0 rpm: Engine stopped
    0 rpm displayed when CAN communication malfunctions
    Accelerator Pedal Angle
    [Accel Pedl Angl]
    Accelerator pedal angle:
    Min.: 0 %, Max.: 100 %
    0 %: Accelerator pedal released
    0 % displayed when CAN communication malfunctions
    Theoretical Engine Torque
    [Theoretic Torq]
    Theoretical engine torque:
    Min.: 0 N*m, Max.: 255 N*m
    0 N*m: Idling
    -
    Clutch Position (Current)
    [Clutch Pos-Cur]
    Current clutch position:
    Min.: 0 mm, Max.: 127.998 mm
    19.0 mm (0.74 in.) to 44.0 mm (1.73 in.)
    Current clutch position displayed
    Shift Position (Current)
    [Shift Pos-Cur]
    Current shift position:
    Min.: 0 mm, Max.: 127.998 mm
    5.0 mm (0.20 in.) to 31.9 mm (1.25 in.)
    Current shift position value displayed (1st, 3rd, 5th, or Neutral, or 2nd, 4th, Reverse)
    Select Position (Current)
    [Select Pos-Cur]
    Current select position:
    Min.: 0 mm, Max.: 127.998 mm
    3.0 mm (0.11 in.) to 29.0 mm (1.14 in.)
    Current select position value displayed (gear shift fork shaft No. 1, No. 2 or No. 3)
    Shift Lever Position Judge
    [Shift Pos Judge]
    Shift lever position:
    INVALID POSITION, P, R, N, E, M
    Actual shift lever position displayed
    -
    Calculated AT Oil Temperature
    [AT Oil Temp]
    Transmission fluid temperature calculated by ECU:
    Min.: -128°C, Max.: 127°C
    Equivalent to actual transmission fluid temperature
    -
    Shift Lever Switch Signal1
    [Shift SW Sig1]
    Shift lever switch signal (+):
    OFF or ON
    ON: Shift lever position in (+)
    OFF: Other than above
    LSW1(LSW+) terminal signal of transmission control ECU
    Shift Lever Switch Signal2
    [Shift SW Sig2]
    Shift lever switch signal (R):
    OFF or ON
    ON: Shift lever position in (R)
    OFF: Other than above
    LSW2 (LSWR) terminal signal of transmission control ECU
    Shift Lever Switch Signal3
    [Shift SW Sig3]
    Shift lever switch signal (M) or (E):
    OFF or ON
    ON: Shift lever position in (E), (M), (+) or (-)
    OFF: Shift lever position in (R) or (N)
    LSW3 (LSWS) terminal signal of transmission control ECU
    Shift Lever Switch Signal4
    [Shift SW Sig4]
    Shift lever switch signal (N):
    OFF or ON
    ON: Shift lever position in (N)
    OFF: Other than above
    LSW4 (LSWN) terminal signal of transmission control ECU
    Shift Lever Switch Signal5
    [Shift SW Sig5]
    Shift lever switch signal (-):
    OFF or ON
    ON: Shift lever position in (-)
    OFF: Other than above
    LSW5 (LSW-) terminal signal of transmission control ECU
    Shift Lever Check Signal1
    [Shift Chek Sig1]
    Check signal of shift lever switch signal 2:
    OFF or ON
    OFF: Shift lever position in (R)
    ON: Other than above
    LS2C (LSRC) terminal signal of transmission ECU
    Reversal signal of LSW2 (LSWR) (ON and OFF reversed)
    Shift Lever Check Signal2
    [Shift Chek Sig2]
    Check signal of shift lever switch signal 3:
    OFF or ON
    OFF: Shift lever position in (E), (M), (+) or (-)
    ON: Shift lever position in (R) or (N)
    LS3C (LSSC) terminal signal of transmission control ECU
    Reversal signal of LSW3 (LSWS) (ON and OFF reversed)
    Shift Lever Check Signal3
    [Shift Chek Sig3]
    Check signal of shift lever switch signal 4:
    OFF or ON
    OFF: Shift lever position in (N)
    ON: Other than above
    LS4C (LSNC) terminal signal of transmission ECU
    Reversal signal of LSW4 (LSWN) (ON and OFF reversed)
    T/M Reverse Switch Signal
    [T/M R SW Sig]
    Transmission reverse switch signal:
    OFF or ON
    ON: Transmission gear in reverse
    OFF: Other than above
    During malfunctions, indicator shows either OFF or ON continuously, regardless of gear position
    Ignition Signal
    [Ignition Sig]
    Ignition switch signal:
    OFF or ON
    ON: Ignition switch on (IG)
    -
    Mode Switch Signal
    [Mode SW Sig]
    Transmission shift main switch signal:
    OFF or ON
    ON: Sequential shift control (M-mode) selected
    -
    Es Mode Switch Signal
    [Es SW Sig]
    Es Mode Switch Signal:
    OFF or ON
    ON: Sporty [Es] mode selected (Automatic shift control)
    -
    Parking Brake Signal
    [Pkb Sig]
    Parking brake switch signal:
    OFF or ON
    ON: Parking brake applied
    OFF: Parking brake released
    -
    Brake Switch Signal2
    [Brake SW Sig2]
    Brake switch signal (ST1-):
    OFF or ON
    OFF: Brake pedal depressed
    ON: Brake pedal released
    ST1- terminal signal of transmission control ECU
    Brake Switch Signal1
    [Brake SW Sig1]
    Brake switch signal (STP):
    OFF or ON
    ON: Brake pedal depressed
    OFF: Brake pedal released
    STP terminal signal of transmission control ECU
    STA Switch Signal
    [STA SW Sig]
    STA signal:
    OFF or ON
    ON: During cranking
    -
    Gear Position (Current)
    [Gear Pos-Cur]
    Current gear position:
    Min.: 0, Max.: 255
    Actual gear position displayed
    0 = Non
    1 to 6 = 1st to 6th
    254 = Neutral
    255 = Reverse
    Gear Position (Target)
    [Gear Pos-Tar]
    Target gear position:
    Min.: 0, Max.: 255
    When shift lever not operated:
    Target gear position equals current gear position
    0 = Non
    1 to 6 = 1st to 6th
    254 = Neutral
    255 = Reverse
    Clutch Position (Target)
    [Clutch Pos-Tar]
    Target clutch position:
    Min.: 0 mm, Max.: 127.998 mm
    Difference between actual and target clutch positions:
    Maximum of 15 mm during gear change control operation (varies with vehicle condition)
    -
    Shift Position (Target)
    [Shift Pos-Tar]
    Target shift position:
    Min.: 0 mm, Max.: 127.998 mm
    Difference between actual and target shift positions:
    Maximum of 15 mm during gear change control operation (varies with vehicle condition)
    -
    Select Position (Target)
    [Select Pos-Tar]
    Target select position:
    Min.: 0 mm, Max.: 127.998 mm
    Difference between actual and target select positions:
    Maximum of 15 mm during gear change control operation (varies with vehicle condition)
    -
    Clutch Motor Current Req
    [Clutch Motor Req]
    Requested clutch motor current from CPU:
    Min.: -50 A, Max.: 50 A
    -20 to 20 A
    Instruction (calculated) current value from CPU
    Clutch Motor Current MMT
    [Clutch Motor]
    Actual clutch motor current:
    Min.: -50 A, Max.: 50 A
    -20 to 20 A
    0 A: When clutch motor not in operation
    Shift Motor Current Req
    [Shift Motor Req]
    Requested shift motor current from CPU:
    Min.: -50 A, Max.: 50 A
    -40 to 40A
    Instruction (calculated) current value from CPU
    Shift Motor Current MMT
    [Shift Motor]
    Actual shift motor current:
    Min.: -50 A, Max.: 50 A
    -40 to 40A
    0 A: When shift motor not in operation
    Select Motor Current Req
    [Select Motor Req]
    Requested select motor current from CPU:
    Min.: -50 A, Max.: 50 A
    -25 to 25 A
    Instruction (calculated) current value from CPU
    Select Motor Current MMT
    [Select Motor]
    Actual select motor current:
    Min.: -50 A, Max.: 50 A
    -25 to 25 A
    0 A: When select motor not in operation
    Base Clutch Load
    [Base Clutch Load]
    Base clutch load:
    Min.: -1000 N, Max.: 1000 N
    Learning value shown
    Base clutch load:
    Calculated from average clutch motor current when ECU performing initialization and learning of clutch system
    Current Clutch Load
    [Current Clutch Load]
    Current clutch load (calculated value):
    Min.: -1000 N, Max.: 1000 N
    Reference value (varies with vehicle condition)
    39.33 to 45.29: Stopper position
    37.07 to 43.03: Complete engagement position
    24.5 to 35.25: Standby position
    Current clutch load:
    Calculated from average clutch motor current
    Difference between Base Clutch Load and Current Clutch Load increases as clutch disks wear away
    After performing LCC adjustment, difference decreases (Almost same as Base Clutch Load value)
    Clutch Adjust Count
    [Clutch Adj Cnt]
    Number of LCC (Load Controlled Clutch cover) adjustment performed:
    Min.: 0 , Max.: 255
    -
    When clutch motor stroke amount reaches certain value, the count increases by 1
    Clutch Adjust Fail Count
    [Clutch Adj Fail]
    Number of LCC (Load Controlled Clutch cover) adjustment judged unnecessary:
    Min.: 0 , Max.: 255
    -
    When difference between Base Clutch Load and Current Clutch Load exceeds threshold, the count increases by 1
    Clutch Adjust Detection
    [Clutch Adj Detect]
    Number of LCC (Load Controlled Clutch cover) adjustment required:
    Min.: 0 , Max.: 255
    -
    When difference between Base Clutch Load and Current Clutch Load exceeds threshold, the count increases by 1
    Mode Changes
    [Mode Changes]
    System control mode:
    Min.: 0, Max.: 255
    -
    11: System wake-up control mode
    12: Vehicle driving control mode
    13: System end control mode
    14: System initialization mode
    17: Engine starting control mode
    20: Fixed gear shift control mode
    21: Gear shift control mode
    22: Shift lever lock control mode
    25: Shut-down control mode
    26: Vehicle stationary control mode
    27: Vehicle start off control mode
    Gear Mode Changes
    [Gear Mode]
    Gear change mode indication:
    Min.: 0, Max.: 255
    -
    -
    1st Uplock Signal
    [1st Uplock Sig]
    1st gear up-lock signal:
    OFF or ON
    -
    If gear shift fails, uplock signal indicates whether transmission up-lock has occurred or not
    Up-lock:
    Transmission gear momentarily cannot be engaged due to mechanical reasons (not malfunction)
    2nd Uplock Signal
    [2nd Uplock Sig]
    2nd gear up-lock signal:
    OFF or ON
    3rd Uplock Signal
    [3rd Uplock Sig]
    3rd gear up-lock signal:
    OFF or ON
    4th Uplock Signal
    [4th Uplock Sig]
    4th gear up-lock signal:
    OFF or ON
    5th Uplock Signal
    [5th Uplock Sig]
    5th gear up-lock signal:
    OFF or ON
    Rev Uplock Signal
    [Rev Uplock Sig]
    Reverse gear up-lock signal:
    OFF or ON
    Vehicle Speed Signal Open
    [Vehicle Spd Open]
    Vehicle speed signal circuit open judgement:
    OFF or ON
    OFF: During vehicle running
    ON: When momentarily interruption in vehicle speed signal
    Input Rev Signal Open
    [In Rev Open]
    Input revolution signal circuit open judgement:
    OFF or ON
    OFF: During engine running
    ON: When abnormal pulse interval detected
    Creep Control
    [Creep Ctrl]
    Vehicle creep control mode:
    OFF or ON
    ON: Clutch partial engagement continues for long time
    Clutch partially engaged when following conditions met:
    1. Engine running
    2. Transmission gear in 1st, 2nd or Reverse
    3. Brake pedal not depressed
    4. Parking brake released
    5. Accelerator pedal released
    Low Voltage Signal
    [Low Volt]
    +B terminal low voltage judgement:
    OFF or ON
    OFF: +B terminal voltage 8 V or more
    -
    Run Off Signal
    [Run Off Sig]
    Vehicle run-off judgement
    OFF or ON
    OFF: While vehicle running
    ON: High differential spin occurred sharply at differential gear
    When following conditions met, transmission control ECU detects run-off in vehicle and restricts gear shift:
    1. Accelerator pedal angle exceeds threshold
    2. SPD signal change rate above threshold
    3. Shift position in 1st, 2nd or 3rd
    Clutch Heat
    [Clt Heat]
    Clutch heat judgement:
    OFF or ON
    OFF: Engine idling, gear in neutral
    ON: Calculated clutch temperature 280°C (536°F) or more
    Clutch temperature calculated from relative revolution speed between engine and transmission input shaft, clutch torque, heat radiation, heat conduction, sum of current clutch temperature and variation in clutch temperature, etc.
    Clutch Heat and Overuse
    [Clt Heat Overuse]
    Clutch heat and overuse judgement:
    OFF or ON
    OFF: Engine idling, gear in neutral
    ON: Calculated clutch temperature 330°C (626°F) or more
    Clutch Motor Current Enable
    [Clt Curr Ena]
    Clutch motor current enabled
    OFF or ON
    OFF: Target clutch motor current less than 1 A
    ON: OFF condition not met
    -
    Motor Relay Signal
    [Mot Relay Sig]
    AMT relay drive signal:
    OFF or ON
    ON: Ignition switch on (IG)
    OFF: Ignition switch off and after system shut-down
    -
    Shift Lever Lock Solenoid
    [SLS]
    Shift lever lock solenoid operation:
    OFF or ON
    OFF: Shift lever locked
    -
    Clutch Touch Position
    [Clt Touch Pos]
    Clutch touch position:
    Min.: 0 mm, Max.: 127.998 mm
    Learning value shown
    Difference between Clutch Touch position and Clutch Clamp Position within 4.0 mm (0.16 in.) to 16.0 mm (0.63 in.)
    Clutch Clamp Position
    [Clt Clamp Pos]
    Clutch clamp position:
    Min.: 0 mm, Max.: 127.998 mm
    Learning value shown
    Difference between Clutch Touch position and Clutch Clamp Position within 4.0 mm (0.16 in.) to 16.0 mm (0.63 in.)
    Neutral Position (Shift)
    [N Pos (Shift)]
    Neutral position (shift position):
    Min.: 0 mm, Max.: 127.998 mm
    Learning value shown
    Median value between [3rd Pos (Shift)] and [4th Pos (Shift)] displayed
    Neutral Position (Select)
    [N Pos (Sel)]
    Neutral position (select position):
    Min.: 0 mm, Max.: 127.998 mm
    Learning value shown
    Median value between [1st Pos (Sel)] and [5th Pos (Sel)] displayed
    1st Gear Position (Shift)
    [1st Pos (Shift)]
    1st gear position (shift position):
    Min.: 0 mm, Max.: 127.998 mm
    Learning value shown
    1. Difference between [1st Pos (Shift)] and [2nd Pos (Shift)] within 15.0 mm (0.59 in.) to 19.5 mm (0.77 in.)
    2. Difference between [1st Pos (Shift)] and [3rd Pos (Shift)] within 1.5 mm (0.06 in.)
    1st Gear Position (Select)
    [1st Pos (Sel)]
    1st gear position (select position):
    Min.: 0 mm, Max.: 127.998 mm
    Learning value shown
    Difference between [1st Pos (Sel)] and [3rd Pos (Sel)] within 5.5 mm (0.22 in.) to 8.5 mm (0.33 in.)
    2nd Gear Position (Shift)
    [2nd Pos (Shift)]
    2nd gear position (shift position):
    Min.: 0 mm, Max.: 127.998 mm
    Learning value shown
    Difference between [1st Pos (Shift)] and [2nd Pos (Shift)] within 15.0 mm (0.59 in.) to 19.5 mm (0.77 in.)
    2nd Gear Position (Select)
    [2nd Pos (Sel)]
    2nd gear position (select position):
    Min.: 0 mm, Max.: 127.998 mm
    Learning value shown
    Difference between [2nd Pos (Sel)] and [4th Pos (Sel)] within 5.5 mm (0.22 in.) to 8.5 mm (0.33 in.)
    3rd Gear Position (Shift)
    [3rd Pos (Shift)]
    3rd gear position (shift position):
    Min.: 0 mm, Max.: 127.998 mm
    Learning value shown
    1. Difference between [3rd Pos (Shift)] and [4th Pos (Shift)] within 15.0 mm (0.59 in.) to 19.5 mm (0.77 in.)
    2. Difference between [5th Pos (Shift)] and [3rd Pos (Shift)] within 1.5 mm (0.06 in.)
    3rd Gear Position (Select)
    [3rd Pos (Sel)]
    3rd gear position (select position):
    Min.: 0 mm, Max.: 127.998 mm
    Learning value shown
    Difference between [3rd Pos (Sel)] and [5th Pos (Sel)] within 5.5 mm (0.22 in.) to 8.5 mm (0.33 in.)
    4th Gear Position (Shift)
    [4th Pos (Shift)]
    4th gear position (shift position):
    Min.: 0 mm, Max.: 127.998 mm
    Learning value shown
    1. Difference between [3rd Pos (Shift)] and [4th Pos (Shift)] within 15.0 mm (0.59 in.) to 19.5 mm (0.77 in.)
    2. Difference between [R Pos (Shift)] and [4th Pos (Shift)] within 1.5 mm (0.06 in.)
    4th Gear Position (Select)
    [4th Pos (Sel)]
    4th gear position (select position):
    Min.: 0 mm, Max.: 127.998 mm
    Learning value shown
    Difference between [R Pos (Sel)] and [4th Pos (Sel)] within 5.5 mm (0.22 in.) to 8.5 mm (0.33 in.)
    5th Gear Position (Shift)
    [5th Pos (Shift)]
    5th gear position (shift position):
    Min.: 0 mm, Max.: 127.998 mm
    Learning value shown
    1. Difference between [R Pos (Shift)] and [5th Pos (Shift)] within 15.0 mm (0.59 in.) to 19.5 mm (0.77 in.)
    2. Difference between [3rd Pos (Shift)] and [5th Pos (Shift)] within 1.5 mm (0.06 in.)
    5th Gear Position (Select)
    [5th Pos (Sel)]
    5th gear position (select position):
    Min.: 0 mm, Max.: 127.998 mm
    Learning value shown
    Difference between [5th Pos (Sel)] and [3rd Pos (Sel)] within 5.5 mm (0.22 in.) to 8.5 mm (0.33 in.)
    Reverse Gear Pos (Shift)
    [R Pos (Shift)]
    Reverse gear position (shift position):
    Min.: 0 mm, Max.: 127.998 mm
    Learning value shown
    1. Difference between [R Pos (Shift)] and [5th Pos (Shift)] within 15.0 mm (0.59 in.) to 19.5 mm (0.77 in.)
    2. Difference between [R Pos (Shift)] and [4th Pos (Shift)] within 1.5 mm (0.06 in.)
    Reverse Gear Pos (Select)
    [R Pos (Sel)]
    Reverse gear position (select position):
    Min.: 0 mm, Max.: 127.998 mm
    Learning value shown
    Difference between [R Pos (Sel)] and [4th Pos (Sel)] within 5.5 mm (0.22 in.) to 8.5 mm (0.33 in.)
    Possibility of T/M Uplock
    [T/M Uplock]
    Possibility of transmission up-lock:
    No or Yes
    No: Initialization and learning complete
    Yes: Transmission gear temporarily could not be engaged due to mechanical reasons during gear position learning
    Learn-Clutch Standby Point
    [Lern-Stby_Pnt]
    Clutch actuator standby position learning:
    Notexec, Fail or Exec
    Exec: Initialization and learning complete
    -
    Learning-T/M
    [Lern-T/M]
    Learning T/M system:
    Notexec, Fail or Exec
    Exec: Initialization and learning complete
    -
    Learn-Clutch Stopper Point
    [Lern-Stppr_Pnt]
    Clutch actuator stopper position learning:
    Notexec, Fail or Exec
    Exec: Initialization and learning complete
    -
    # Codes
    [# Codes]
    Number of codes:
    Min.: 0, Max.: 255
    -
    Number of detected DTCs
    Check Mode
    [Check Mode]
    Check mode:
    OFF or ON
    ON: Check mode ON
    -


ACTIVE TEST

HINT:
Performing an Active Test enables components including the relays, VSV (Vacuum Switching Valve), and actuators, to be operated without removing any parts. The Active Test can be performed with an intelligent tester. Performing an Active Test as the first step of troubleshooting is one method of shortening diagnostic time.
Data List can be displayed during Active Tests.

  1. Connect an intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG) and turn the tester ON.

  3. Select the following menu items: Powertrain / Multi-Mode M/T / Active Test.

  4. Perform the Active Test by referring to the table below.

    Items
    Test Details/Vehicle conditions
    Diagnosis Notes
    Target Gear Position Control
    [Test Details]
    Target gear position control (Gear position)
    N, 1st, 2nd, 3rd, 4th, 5th, R
    [Vehicle Conditions]
    Ignition switch on (IG), Engine stopped, Vehicle stationary, Shift lever N position
    If shift and select actuator does not shift to the gear indicated, there could be some malfunctions in the following parts:
    Shift stroke sensor
    Select stroke sensor
    Shift and select actuator assembly
    AMT relay
    Transmission assembly
    Transmission control ECU
    Target Clutch Control
    [Test Details]
    Target clutch control
    Standby position: Standby
    Clamp position: Clamp
    [Vehicle Conditions]
    Ignition switch on (IG), Engine stopped, Vehicle stationary, Shift lever N position
    If clutch actuator does not operate to the position indicated, there could be some malfunctions in the following parts:
    Clutch stroke sensor
    Clutch actuator assembly
    AMT relay
    Clutch release bearing
    Clutch release fork
    Transmission control ECU

← FAIL-SAFE CHART (from Nov 2005)DIAGNOSTIC TROUBLE CODE CHART (from Nov 2005) →