2005-2008 Yaris · Service Manual TRANSMISSION

FAIL-SAFE CHART

System information · Vehicles built from Nov 2005


FAIL-SAFE CHART
  1. If any of the following codes is recorded, the transmission control ECU enters the fail-safe mode.

    DTC No.
    Malfunction Areas
    Fail-safe Functions
    Fail-safe Deactivation Conditions
    1. P0806
    2. P0807
    3. P0808
    4. P0810
    5. P0900
    1. Clutch stroke sensor or its circuit
    2. Clutch actuator assembly or its circuit
    1. Gear does not change
    2. Vehicle does not start moving again after stopping
    Either (a) or (b) met:
    1. (a) All of following conditions met:
      1. Pass condition detected
      2. Shift lever in N position
      3. Transmission gear in neutral*
      4. Vehicle speed less than 6 km/h (3.73 mph)
    2. (b) Pass condition detected and ignition switch off
    1. P0807
    2. P0808
    3. P0906
    4. P0907
    5. P0916
    6. P0917
    1. Clutch stroke sensor or its circuit
    2. Select stroke sensor or its circuit
    3. Shift stroke sensor or its circuit
    1. Limit to 3rd gears or lower
    Either of (a) or (b) met:
    1. (a) All of the following conditions met:
      1. Pass condition detected
      2. Shift lever in N position
      3. Transmission gear in neutral*
      4. Vehicle speed less than 6 km/h (3.73 mph)
    2. (b) Pass condition detected and ignition switch off
    1. P0905
    2. P0906
    3. P0907
    4. P0909
    5. P0910
    6. P0915
    7. P0916
    8. P0917
    9. P0919
    10. P0920
    1. Shift stroke sensor or its circuit
    2. Shift actuator assembly or its circuit
    3. Select stroke sensor or its circuit
    4. Select actuator assembly or its circuit
    1. Gear does not change
    2. Vehicle does not start moving again after stopping
    Either (a) or (b) met:
    1. (a) All of following conditions met:
      1. Pass condition detected
      2. Shift lever in N position
      3. Vehicle speed less than 6 km/h (3.73 mph)
    2. (b) Pass condition detected and ignition switch off
    1. P0725
    1. Engine speed input circuit
    1. Convert engine revolution signals into CAN communication signals
    2. No effect
    Either (a) or (b) met:
    1. (a) All of following conditions met:
      1. Pass condition detected
      2. Actual gear position not in neutral
      3. Clutch engaged
    2. (b) Pass condition detected and ignition switch off
    1. P0500
    2. P0715
    1. Vehicle speed sensor or its circuit
    2. Transmission revolution sensor or its circuit
    1. Gear does not shift down while driving
    2. Only possible to drive in 1st or reverse gears after vehicle stops
    Either (a) or (b) met:
    1. (a) All of following conditions met:
      1. Pass condition detected
      2. Vehicle speed less than 6 km/h (3.73 mph)
      3. Accelerator pedal released
      4. Brake pedal depressed
    2. (b) Pass condition detected and ignition switch off
    1. P0603
    2. P0885
    1. Transmission control ECU
    2. Clutch actuator, shift actuator, select actuator power source circuit
    1. Gear does not change
    2. Engine cannot be started
    3. Transmission control ECU stops engine when vehicle stops
    Pass condition detected and ignition switch off
    1. P0820
    1. Shift lever position sensor or its circuit
    2. Transmission shift main switch or its circuit
    1. Impossible to enter M-mode
    2. Gear does not shift to 1st or reverse (and forward or backward gears)
    Pass condition detected and ignition switch off
    1. P0335
    2. P0339
    1. Crankshaft position sensor or its circuit
    1. Gear does not change
    Pass condition detected and ignition switch off
    1. U0100
    1. CAN communication signal circuit
    1. Gear does not change
    2. Only possible to drive in 1st or reverse gears after vehicle stops
    Either (a) or (b) met:
    1. (a) All of following conditions met:
      1. Pass condition detected
      2. Vehicle stopped
      3. Accelerator pedal released
      4. Brake pedal depressed
    2. (b) Pass condition detected and ignition switch off

    HINT:
    1. *: Transmission gear: Actual transmission gear position
    2. The transmission control ECU identifies the actual transmission gear position through the signals from the shift stroke sensor and select stroke sensor.
    3. The transmission control ECU identifies the shift lever position through the signal from the shift lever position sensor.

← DTC CHECK / CLEAR (from Nov 2005)DATA LIST / ACTIVE TEST (from Nov 2005) →