2005-2008 Yaris · Service Manual TRANSMISSION

Multi-Mode Manual Transmission Warning Light Circuit

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

The combination meter interprets the multi-mode manual transmission system condition according to the information from the INDC and INDA circuits, and if necessary, illuminates (blinks) the multi-mode manual transmission warning light and sounds the buzzer.
  1. INDC Terminal Circuit:
    The battery voltage is constantly supplied to the INDC circuit. If the INDC circuit is open, the combination meter detects a malfunction in the circuit and illuminates the multi-mode manual transmission warning light. The INDC circuit is used to send the multi-mode manual transmission warning light signal to the combination meter when the ignition switch is off.
  2. INDA Terminal Circuit:
    Power is supplied to the INDA circuit when the ignition switch is on (IG). While the ignition switch is on (IG), the combination meter controls the multi-mode manual transmission warning light ON/OFF condition according to the signal from the INDA circuit. The INDA circuit is used to send the signal for multi-mode manual transmission warning light and shift position indicator to the combination meter.
The contents of signals from the INDC and INDA circuits, and the status of the multi-mode manual transmission warning light and indicator are shown in the table below.
When Ignition Switch ON: 
INDA circuit state (at combination meter)
Normal
Inconsistent signal input (3 seconds or more)
Interrupted signal input (3 seconds or more)
INDC circuit (at combination meter)
Normal
+B short or open
Normal
+B short or open
Normal
+B short or open
Shift position indicator
*1
ON
depends on communication signal
ON
depends on communication signal
OFF
OFF
OFF
OFF
Multi-mode manual transmission warning light
ON
depends on communication signal
ON
depends on communication signal
ON
ON
ON
ON
*1: when shift position indicator ON, the number or letter segments are illuminated.
When Ignition Switch OFF: 
INDA circuit state (at combination meter)
Normal
Inconsistent signal input (3 seconds or more)
Interrupted signal input (3 seconds or more)
INDC circuit state (at combination meter)
Normal
+B short or open
Normal
+B short or open
Normal
+B short or open
Shift position indicator
*1
ON
depends on communication signal
ON
depends on communication signal
OFF
OFF
OFF
OFF
Multi-mode manual transmission warning light
ON
depends on communication signal
ON
depends on communication signal
ON
ON
OFF
ON
*1: when shift position indicator ON, the number or letter segments are illuminated.

WIRING DIAGRAM

C127416E01

INSPECTION PROCEDURE

HINT:
  1. Check that the multi-mode manual transmission warning light and shift position indicator light come on.
    Under normal conditions, the shift position indicator indicates the current gear position while the ignition switch is turned on (IG), and the multi-mode manual transmission warning light comes on for bulb check for approximately 5 seconds when the ignition switch is turned from off to on (IG).
    If the shift position indicator light does not come on, the INDA circuit may be malfunctioning. If the multi-mode manual transmission warning light does not come on, the INDA and/or INDC circuits may be malfunctioning.
  2. The buzzer built into the combination meter sounds when the following conditions are met.
    1. The shift lever is in any position except N.
    2. The driver's door is open.
    3. Vehicle speed is 10 km/h (6.21 mph) or less.
    4. Engine speed is 400 rpm or more.


1. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU - COMBINATION METER ASSEMBLY)

  1. C127417E01
    Disconnect the transmission control ECU connector.

  1. Disconnect the combination meter connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    INDC (D79-29) - BRQ (D1-13)
    Below 1 Ω
    INDA (D79-31) - TX+ (D1-8)
    Below 1 Ω
    INDC (D79-29) - Body ground
    10 kΩ or higher
    INDA (D79-31) - Body ground
    10 kΩ or higher

  1. Reconnect the transmission control ECU connector.

  1. Reconnect the combination meter connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT COMBINATION METER

  1. C127418E01
    Measure the voltage between the terminal of the combination meter and the body ground.

    Standard voltage:
    Tester Connection
    Conditions
    Specified Conditions
    TX+ (D1-8) - Body ground
    Ignition switch off
    3.64 V or higher
    TX+ (D1-8) - Body ground
    Ignition switch on (IG)
    Below 1.44 V
    BRQ (D1-13) - Body ground
    Always
    Below 1.44 V



NG
INSPECT METER / GAUGE SYSTEM
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE


← Shift Lock Solenoid Circuit (from Nov 2005)Parking Brake Switch Circuit (from Nov 2005) →