2005-2008 Yaris · Service Manual TRANSMISSION

ADJUSTMENT

Removal / installation · Vehicles built from Nov 2005


1. USING INTELLIGENT TESTER: CLAMP POSITION ADJUSTMENT (CLUTCH POSITION ADJUSTMENT)

HINT:
  1. The multi-mode manual transmission system has a load controlled clutch cover (adjustment system). The pressure plate moves depending on the wear condition of the clutch disc lining.
  2. When removing or installing any parts related to the multi-mode manual transmission system, move the clutch actuator to the clutch clamp position. This is for normal operation of the load controlled clutch cover (adjustment system).
  3. If the clutch position adjustment operation input fails, perform the operation again from step (a) more than 15 seconds after turning the ignition switch off.

NOTICE:
Do not depress the brake pedal while performing the clamp position adjustment using an intelligent tester.

  1. Prepare the vehicle:

    1. Stop the vehicle.
    2. Shift the lever into the N position.
    3. Turn the ignition switch off.
    4. Apply the parking brake.

  1. A107926E01
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the intelligent tester ON.

  1. Select the following menu items: Powertrain / Multi-Mode M/T / Utility / Parts Exchange.

  1. C114373E01
    Read the information.

  1. Press the Next key.

  1. C114374E01
    Read the information.

  1. After checking the vehicle condition, press the Next key.

  1. C114375E01
    Read the information.

  1. Press the Next key.

  1. C114376E01
    Read the information.

  1. Press the Next key.

  1. C114377E01
    On the Multi-Mode M/T / Utility screen, select Step 1 Clutch Position Adjustment (Clamp Position Adjustment).

  1. Press the Next key.

  1. C114378E01
    Read the information.

  1. Press the Next key.

  1. Complete Clutch Position Adjustment.

  1. Turn the intelligent tester OFF.

  1. Turn the ignition switch off.

  1. Replace the malfunctioning parts.

    HINT:
    Perform [Initialization and Learning] after repairing the multi-mode manual transmission control system (Click here).


2. WITHOUT USING INTELLIGENT TESTER: CLAMP POSITION ADJUSTMENT (CLUTCH POSITION ADJUSTMENT)

HINT:
  1. The multi-mode manual transmission system has a load controlled clutch cover (adjustment system). The pressure plate moves depending on the wear condition of the clutch disc lining.
  2. When removing or installing any parts related to the multi-mode manual transmission system, move the clutch actuator to the clutch clamp position. This is for normal operation of the load controlled clutch cover (adjustment system).
  3. If the clutch position adjustment operation input fails, perform the operation again from step (a) more than 15 seconds after turning the ignition switch off.

  1. Prepare the vehicle.

    1. Stop the vehicle.
    2. Shift the lever into the N position.
    3. Turn the ignition switch off.
    4. Apply the parking brake.

  1. A082779E56
    Using SST, connect terminals TC (13) and CG (4) of the DLC3
    SST
    09843-18040  

  1. Turn the ignition switch on (IG) with the brake pedal released.

  1. BR03890
    Depress the brake pedal 7 times or more within 3 seconds.

    1. The buzzer sounds twice with an interval of 0.25 seconds.

  1. Depress the brake pedal.

  1. Shift the shift lever in the following sequence with the brake pedal depressed: N→E→M→+→M→+→M→+→M→+→M→E→N.

    C127398E01

  1. Release the brake pedal.

  1. BR03890
    Depress the brake pedal again.

    1. The buzzer sounds once at intervals of 2.5 seconds.

      HINT:
      If the buzzer does not sound at this time, wait at least 15 seconds after turning the ignition switch off. Then, perform the procedure from step (a) again.

  1. Depress the brake pedal 3 times or more within 2 seconds.

    1. The buzzer sounds twice with an interval of 0.25 seconds.

  1. Depress the brake pedal.

  1. Shift the shift lever to the [-] position with the brake pedal depressed.

  1. Release the brake pedal.

  1. Complete clutch position adjustment.

  1. Turn the ignition switch OFF and wait at least 10 seconds.

  1. Disconnect the SST from terminals TC and CG of the DLC3.

  1. Repair the malfunctioning parts.

    HINT:
    Perform [Initialization and Learning] after repairing the multi-mode manual transmission control system (Click here).

← DIAGNOSTIC TROUBLE CODE CHART (from Nov 2005)P0500 Vehicle Speed Sensor "A" (from Nov 2005) →