INITIALIZATION
Troubleshooting · Vehicles built from Nov 2005
| INITIALIZATION AND LEARNING USING INTELLIGENT TESTER |
- HINT:
- By using an intelligent tester, initialization and learning of the multi-mode manual transmission system can be performed sequentially. Under manual operation (not using intelligent tester), initialization and learning must be performed individually.
- The learning values and the DTC history of the multi-mode manual transmission system are stored in the EEPROM in the transmission control ECU. The stored information is not cleared even when the negative terminal of the battery is disconnected. To clear all the stored information, initialize the transmission control ECU.
- Perform the procedure below to ensure that the initialized transmission control ECU stores the adjusted clutch position (stopper position, clamp position, and standby position) or gear position (shift position and select position).
- If the initialization cannot be performed normally, there may be a malfunction in the shift lever position sensor, NE signals, or CAN communication.
- When replacing the following parts, proceed with the operation in the order listed in the table below.
- By using an intelligent tester, initialization and learning of the multi-mode manual transmission system can be performed sequentially. Under manual operation (not using intelligent tester), initialization and learning must be performed individually.
| Parts installed |
Operation order |
See procedure |
|
1. INITIALIZATION OF MULTI-MODE MANUAL TRANSMISSION SYSTEM [Initialization of ECU] |
See below |
| 2. LEARNING OF MULTI-MODE MANUAL TRANSMISSION SYSTEM |
See below |
|
| 3. SYNCHRONIZATION POSITION CALIBRATION |
Click here
|
|
|
1. INITIALIZATION OF MULTI-MODE MANUAL TRANSMISSION SYSTEM [Initialization of transmission] |
See below |
| 2. LEARNING OF MULTI-MODE MANUAL TRANSMISSION SYSTEM |
See below |
|
| 3. SYNCHRONIZATION POSITION CALIBRATION |
Click here
|
|
|
1. INITIALIZATION OF MULTI-MODE MANUAL TRANSMISSION SYSTEM [Initialization of clutch] |
See below |
| 2. LEARNING OF MULTI-MODE MANUAL TRANSMISSION SYSTEM |
See below |
Prepare the vehicle:
- Stop the vehicle
- Shift the shift lever to the N position.
- Turn the ignition switch off.
- Stop the vehicle
Connect the intelligent tester to the DLC3.

Turn the ignition switch on (IG).
Turn the intelligent tester ON.
Select the following menu items: Powertrain / Multi-Mode M/T / Utility / Parts Exchange.
Read the information.

Press the Next key.
Read the information.

After checking the vehicle condition, press the Next key.
Read the information.

Press the Next key.
Read the information.

Press the Next key.
On the Multi-Mode M/T / Utility screen, select Step 3 Initial Learning.

Press the Next key.
Select the appropriate operation.

- HINT:
- Initialization of clutch: when removing and installing the following parts related to the clutch system.
Clutch actuator, clutch stroke sensor, clutch disc and clutch cover, clutch release bearing, clutch release fork or fork lever, flywheel, and end plate.
- Initialization of transmission: when removing and installing the parts related to the shift and select operation of the transmission assembly.
- Initialization of ECU: This initializes learned values of both the clutch and transmission.
- Initialization of clutch: when removing and installing the following parts related to the clutch system.
Press the Next key.
Read the information.

Press the Next key after turning the ignition switch off.
Wait 10 seconds.

- HINT:
- Count down the seconds from 10 to 0.
Read the information.

Press the Next key after turning the ignition switch on (IG).
Wait 40 seconds.

- HINT:
- Count down the seconds from 40 to 0.
Press the Exit key.

Complete Initialization and Learning.
Turn the intelligent tester OFF and turn the ignition switch off.
Wait at least 20 seconds.
Turn the ignition switch on (IG).
Depress the brake pedal with the shift lever position in the N position.
Start the engine and wait at least 10 seconds.
Shift the gear from neutral to any other position.
- HINT:
- When [Initialization of transmission] was selected at step (p), add the following step between steps (w) and (x).
Additional step: (w') Wait at least 30 seconds.
- If the Initialization and Learning operations fail, perform the operations again from step (a) more than 15 seconds after turning the ignition switch off.
- Perform Synchronization Position Calibration after performing Initialization of transmission or Initialization of ECU.
- Shifting the gear from neutral to any other position at last, the transmission control ECU learns the standby point. At this time, the value of Learn-Clutch Standby Point in the Data List changes from [Notexec] to [Exec].
- When [Initialization of transmission] was selected at step (p), add the following step between steps (w) and (x).
| INITIALIZATION OF MULTI-MODE MANUAL TRANSMISSION SYSTEM WITHOUT USING INTELLIGENT TESTER |
- HINT:
- The learning values and the DTC history of the multi-mode manual transmission system are stored in the EEP ROM in the transmission control ECU. The stored information is not cleared even when the negative terminal of the battery is disconnected. To clear all the stored information, initialize the transmission control ECU.
- If the initialization of the multi-mode manual transmission system fails, perform the operation again from step (a) more than 15 seconds after turning the ignition switch off.
- If the initialization cannot be performed normally, there may be a malfunction in the shift lever position sensor, NE signals, or CAN communication.
- When replacing the following parts, proceed with the operations in the order listed in the table below.
- The learning values and the DTC history of the multi-mode manual transmission system are stored in the EEP ROM in the transmission control ECU. The stored information is not cleared even when the negative terminal of the battery is disconnected. To clear all the stored information, initialize the transmission control ECU.
| Parts installed |
Operation order |
See procedure |
|
1. INITIALIZATION OF MULTI-MODE MANUAL TRANSMISSION SYSTEM [Initialization of ECU] |
See below |
| 2. LEARNING OF MULTI-MODE MANUAL TRANSMISSION SYSTEM |
See below |
|
| 3. SYNCHRONIZATION POSITION CALIBRATION |
Click here
|
|
|
1. INITIALIZATION OF MULTI-MODE MANUAL TRANSMISSION SYSTEM [Initialization of transmission] |
See below |
| 2. LEARNING OF MULTI-MODE MANUAL TRANSMISSION SYSTEM |
See below |
|
| 3. SYNCHRONIZATION POSITION CALIBRATION |
Click here
|
|
|
1. INITIALIZATION OF MULTI-MODE MANUAL TRANSMISSION SYSTEM [Initialization of clutch] |
See below |
| 2. LEARNING OF MULTI-MODE MANUAL TRANSMISSION SYSTEM |
See below |
Prepare the vehicle:
- Stop the vehicle.
- Shift the lever to the N position.
- Turn the ignition switch off.
- Stop the vehicle.
Using SST, connect terminals TC (13) and CG (4) of the DLC3.

- SST
- 09843-18040
Wait at least 10 seconds.
Turn the ignition switch on (IG).
Depress the brake pedal at least 7 times within 3 seconds.

The buzzer sounds twice with an interval of 0.25 seconds.
Depress the brake pedal.
Shift the shift lever in the following sequence with the brake pedal depressed.
- When initializing the ECU: N → E → M → - → M → - → M → - → M → - → E → N.
- When initializing the clutch: N → E → M → + → M → - → M → + → M → - → E → N.
- When initializing the transmission: N → E → M → - → M → - → M → + → M → + → E → N.


- When initializing the ECU: N → E → M → - → M → - → M → - → M → - → E → N.
Release the brake pedal
Depress the brake pedal once.

The buzzer sounds at intervals of 0.5 seconds as follows (an interval of 2.5 seconds exists between each cycle).
- Twice when initializing the ECU (one cycle)
- Three times when initializing the clutch (one cycle)
- Four times when initializing the transmission (one cycle)
- HINT:
- If the buzzer does not sound as specified, wait at least 15 seconds after turning the ignition switch off. Then, perform the procedure from step (a) again.
- If the buzzer sounds at intervals of 1 second (not at intervals of 0.5 seconds), wait at least 15 seconds after turning the ignition switch off. Then, perform the procedure from step (a) again.
- If the buzzer does not sound as specified, wait at least 15 seconds after turning the ignition switch off. Then, perform the procedure from step (a) again.
- Twice when initializing the ECU (one cycle)
Depress the brake pedal 3 times or more within 2 seconds.
The buzzer sounds twice with an interval of 0.25 seconds.
Turn the ignition switch off and wait at least 10 seconds.
The initialization is complete.
Disconnect the SST from terminals TC and CG of the DLC3.
| LEARNING OF MULTI-MODE MANUAL TRANSMISSION SYSTEM WITHOUT USING INTELLIGENT TESTER |
- HINT:
- Perform the procedure below to ensure that the initialized transmission control ECU stores the adjusted clutch position or gear position.
- If the learning of the multi-mode manual transmission system fails, perform the operation again from step (a) more than 15 seconds after turning the ignition switch off.
- Perform the procedure below to ensure that the initialized transmission control ECU stores the adjusted clutch position or gear position.
Prepare the vehicle:
- Stop the vehicle.
- Shift the shift lever to the N position.
- Turn the ignition switch off.
- Stop the vehicle.
Turn the ignition switch on (IG).
Wait at least 40 seconds.
Turn the ignition switch off.
Wait at least 20 seconds.
Turn the ignition switch on (IG).
Start the engine under the following conditions:
- Shift lever is in the N position.
- Brake pedal is depressed.
- HINT:
- The shift N position indicator blinks when the engine starts.
- Shift lever is in the N position.
Wait at least 10 seconds.
Check that the shift N position indicator turns on continuously (stops blinking).
The learning is complete.