2005-2008 Yaris · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL TRANSMISSION CASE OIL SEAL

D032711E01
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a hammer, install the new oil seal.

    SST
    09726-36010  
    09950-70010   (09951-07200)

    Drive in depth:
    9.6 to 10.2 mm (0.378 to 0.402 in.)

    NOTICE:
    Do not damage the oil seal lip.


2. INSTALL TRANSAXLE CASE OIL SEAL

D032710E01
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a hammer, install the new oil seal.

    SST
    09710-20011   (09710-06071)
    09950-70010   (09951-07200)

    Drive in depth:
    1.6 to 2.2mm (0.063 to 0.087 in.)

    NOTICE:
    Do not damage the oil seal lip.


3. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
  1. Coat the spline of the inboard joint with gear oil.

  1. C116899
    Align the inboard joint splines and install the drive shaft with a screwdriver and hammer.

    NOTICE:
    1. Face the cut area of the front drive inboard joint hole snap ring downward.
    2. Do not damage the oil seal.
    3. Do not damage the inboard joint boot.

    HINT:
    Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.


4. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


5. INSTALL FRONT AXLE ASSEMBLY LH
  1. Push the front axle out of the vehicle to align the spline of the drive shaft with the front axle and insert the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Check for any foreign matter on the speed sensor rotor and insertion part.
    4. Do not damage the speed sensor rotor.


6. INSTALL FRONT AXLE ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


7. INSTALL FRONT SUSPENSION LOWER ARM LH

C107513
  1. Install the lower arm onto the steering knuckle with a new castle nut.

    Torque:
    98 N*m{ 1,000 kgf*cm , 72 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new clip.


8. INSTALL FRONT SUSPENSION LOWER ARM RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


9. INSTALL STABILIZER LINK ASSEMBLY LH

C106044
  1. Install the stabilizer link with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.


10. INSTALL STABILIZER LINK ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


11. INSTALL FRONT SPEED SENSOR LH

C112274
  1. Install the speed sensor onto the steering knuckle with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Check that the speed sensor tip and installation portion are free of foreign matter.
    2. Install the speed sensor without turning it from its original installation angle.

  1. C125274
    Install the flexible hose and speed sensor with the bolt.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Install the flexible hose and speed sensor without twisting them.


12. INSTALL FRONT SPEED SENSOR RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


13. INSTALL TIE ROD END SUB-ASSEMBLY LH

C107961
  1. Install the tie rod end onto the steering knuckle with a new castle nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new cotter pin.


14. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


15. INSTALL FRONT AXLE HUB LH NUT LH

C057566
  1. Using a 30 mm socket wrench, install a new axle hub nut.

    Torque:
    216 N*m{ 2,203 kgf*cm , 160 ft.*lbf }

  1. Using a chisel and hammer, caulk the axle hub nut.


16. INSTALL FRONT AXLE HUB LH NUT RH

HINT:
The installation procedure for the RH side is the same as that for the LH side.


17. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


19. ADD TRANSAXLE OIL

D025304E01

Oil grade:
API GL-4

Viscosity:
SAE 75 W-90

Capacity:
1.9 liters (2.0 US qts, 1.7 lmp. qts)


20. CHECK TRANSAXLE OIL LEAKAGE

21. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)

22. CHECK ABS SENSOR SIGNAL (w/o VSC)
(Click here)

23. CHECK VSC SENSOR SIGNAL (w/ VSC)
(Click here)
← REMOVAL (from Nov 2005)COMPONENTS (from Nov 2005) →